Vivint V-SKEY1-345 Quick Reference

The Vivint Secure Key Remote (SKEY1) works with any
allowing users to
and convenience, the SKEY1 allows you to
in your system
enjoy the ease of disarming their system as they
on the

T
panel when the first and third buttons are held down.
providing an extra
on a key ring

Secure Key Remote

(V

Quick Reference

Programming Instructions

(
Use the following guidelines t

Mode

with a Vivint Control Panel, it cannot be changed to either Standard Mode.

Installer Test

Press any of the buttons (for approximately 2 seconds) to send test signals to the panel when it is in Test Mode.

User Test

Test
red LED flashes. (NOTE: If the panel is NOT in Test Mode, the signals will activate the actual designated event.)

Button Functionality

Specifications

Wireless Signal Range

300 feet (91.4 m), open air

Battery

Panasonic CR2032 or equivalent lithium battery

Battery Life

3-5 years under normal usage

Transmitter Frequency

345 MHz

Code Outputs

Arm Away, Arm Stay, Disarm, Panic, Auxiliary

Supervisory Interval

70 minutes per signal (12 hours for panel to report supervision failure)

Operating Temperature Limits

32° to 120°F (0° to 49°C)

Relative Humidity

5-95% Non-Condensing

PRINT INSTRUCTIONS: REFERENCE SHEET V-SKEY1-345 P/N 77-000035-001 REV 1.1 |
INK:
FOLDS: TRI-FOLD VERTICAL, TRI-FOLD HORIZONTAL (TO FIT IN BOX)

BLACK | MATERIAL: 20 LB MEAD BOND | SIZE: 5.50" X 8.50" SCALE 1:1 |

-SKEY1-345)

Vivint Security System,

control their system with the touch of a button. Combining style

arm, disarm, and control another device

anywhere within transmission range of the touchscreen panel. Users

pull up to their house or arming it

ir way out the door.

he SKEY1 also provides reliable security by letting you send a panic signal to the

All signals are encrypted,

level of security. The sleek design of the SKEY1 allows it to easily fit

, or in a pocket or purse.

For more details, go to the Support page at: Vivint.com, and the KIM site at: corp.vivint.com/sites/KIM/)

o add an SKEY1 device to the Vivint system and program the operating mode:

• Add each SKEY1 into the panel as a non-supervised sensor.

• Secure Key Remotes must be "learned" into the panel. SKEY1 devices will not function properly in Secure

Mode if the sensor ID is manually entered into the panel.

MODE PROGRAMMING:
While the panel is learning in the SKEY1 (you must be within 5 feet/1.5 m of the panel), perform these steps:

• Hold the Disarm button as you insert the battery. The LED will turn on solid red indicating the SKEY1 is

ready to have its operating mode set by pressing one of the four buttons:

• Disarm — Standard Mode (the LED blinks once to indicate successful mode selection)

• Arm Staying — Standard Mode + GDR1 (the LED blinks twice)

• Arm Leaving — Secure Mode (the LED blinks three times)

• Asterisk (*) — Secure Mode + GDR1 (the LED blinks four times)

IMPORTANT: Secure Mode should always be used when possible. Once the SKEY1 is placed in Secure

Disarm button: Press until the red LED illuminates to disarm the system.
Arm Staying button: Press until the red LED illuminates to arm in stay mode.
Arm Leaving button: Press until the red LED illuminates to arm in away mode.
Asterisk (*) button: Can be programmed to control other devices via the panel.
Disarm and Arm Leaving buttons: Hold down both buttons until the red

LED begins blinking rapidly (for about 4 seconds) to send a panic signal
to the panel only if the panel is configured to do so.

each button's functionality by holding the button down separately (for approximately 2 seconds) until the

Battery Installation

To install or replace the battery, insert a coin into the top

Use only the recommended replacement battery type (see Specifications).

FCC and Industry Canada Regulatory Declarations*

CAUTION:

This device has been tes ted and found to comply with the
license

These limits a re designed to provide rea sonable protection agains t harmful interference in a residential installati on. This e
and can radiate radio fre quency energy and
communications. However, there is no gua rantee that interference w ill not occur in a particu lar installation
interference to radio or t elevision reception, which can be determi ned by turning the equipment off and on, the user is encou
the interference by one o r more of the following measures:

PRUDENCE

Conformément à la réglem entation d'Industrie Canada, le présent ém etteur radio peut fonctionner avec une
(ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risq ues de brouillage radioé lectriqu
utilisateurs, il faut cho isir le type d'antenne et son gain de s
nécessaire à l'établiss ement d'une communication satisfaisante.
Le présent appareil es t conforme aux CNR d’Industrie Canada applicable s aux appareils radio exempts de
conditions su ivantes:

brouillage es t susceptible d’en co
Ces limites sont conçues pour fournir une protection raisonnable c ontre les interférences nuisibles dans une installation résidentielle. Cet équipement
génère, utilise et peut émettre une énergie de radiofréquence et, s'il n'e
interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des inte rférences no se produiro
installation pa rticulière. Si cet équi
mettant l'équipement hors e t sous tension, l'utilisateur est encourag é à essayer de corriger l'interférence pa r une ou plusie

ntes:

FCC ID:

*For more compliance a nd warranty informatio n, visit: www.vivint.com

Batteries must not be recharged, disassembled

Disposal of
r
Keep away from small children. If batteries are swallowed,

California Only:

distributed in California, USA. Perchlorate material special handling may apply.
visit:

© 2014 Vivint Inc. All Rights Reserved. | www.vivint.com | M/N: KF01 | Doc P/N: 77-000035-001 Rev. 1.1

Wireless Product Notice

Wireless communications hardware provides reliable communication; however, there are limitations whi

• Wireless signals may be blocked by radio signals that occur on or near their operating frequencies.

left corner slot and carefully twist to open the device.

NOTE: The red LED wi ll blink 1-4 ti mes upon ba ttery insertion, indicating the operating mode of the SKEY1.

WARNING! The polarity of the battery must be observed (as shown in the image).

Improper handling of lithium batteries may result in heat generation, explosion, or fire,

which may lead to personal injury. Replace only with the same or equivalent battery type

as recommended by the manufacturer.

AVERTISSEMENT! La polarité de la batterie doit être observée (comme indiqué dans

l'image). Une mauvaise manipulation des piles au lithium peut conduire à la production

de chaleur, une explosion ou un incendie, ce qui peut entraîner des blessures. Remplacez-

le par le même type ou équivalent de la b atterie tel que reco mmandé par le fabricant.

, or disposed of in fire.

used batteries must be made in accordance with the waste recovery and recycling

egulations in your area.

promptly see a doctor.

This Perchlorate warning applies ONLY to Manganese Dioxide Lithium cells sold or

(For more information,

www.dtsc.ca.gov/hazardouswaste/perchlorate)

• The transmitters are re quired to comply with all applicable wireless rules a nd regulations. As such, they have limited

transmitter power and l imited range.

Unauthorized changes or modifications could void the user’s authority to operate the equipment.

-exempt RSS standard(s ). Operation is subject to the following t wo conditions:
(1) This device may not cause harmful interference, and
(2) This device must a ccept any interference received, including interference that may cause undesired o peration of the device.

, if not installed and us ed in accordance with the instructions, may ca use harmful interference to radio

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the re ceiver is connected.

• Consult the dea ler or an experienced radi o/television technician for help.

: Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées.

(1) l’appare il ne doit pas produire de brouillage, et (2) l’utilis ateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

mpromettre le fonctio nnement.

pement provoque des interférences nuisibles à la réception radio ou télévision, ce qui peut être déterminé en

• Réorienter ou dé placer l'antenne de réce ption.

• Augmentez la distance entre l'équipement et le récepteur.

• Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est bran ché.

• Consulter le rev endeur ou un technicien radio / télévision expé rimenté pour de l'aide.

2AAAS-KF01, IC ID: 10941A-KF01

limits for a Class B digital device, pursuant to Part 15 of F CC Rules and Industry Canada

orte que la puissanc e isotrope rayonnée équivalente (p.i.r.e. ) ne dépasse pas l'intensité

st pas installé et ut ilisé conformément aux instructions, il peut causer des

ch must be o bserved.

quipment generates, uses ,

. If this equipment does cause harmful

raged to try to correct

antenne d'un type et d' un gain maximal

e à l'intention des a utres

licence. L’explo itation est autorisée a ux deux

nt pas dans une

urs des mesures suiva