Vivint PB01 Users Manual

Panic Button Remote
(V-PANIC2-345)
Quick Reference
Installer Test
Press and hold the button for 2 seconds to send signals from the device to the control panel.
Specifications
Wireless Signal Range
300 feet (91.4 m), open air
Battery
Panasonic CR2032 or equivalent lithium battery
Battery Life
3-5 years under normal usage
Transmitter Frequency
345 MHz
Code Outputs
Alarm, Alarm Restore, Supervisory, Low Battery
Supervisory Interval
70 minutes per signal (12 hours for panel to report supervision failure)
Operating Temperature Limits
32° to 120°F (0° to 49°C)
Relative Humidity
5-95% Non-Condensing
PRINT INSTRUCTIONS: REFERENCE SHEET V-PANIC2-345 P/N 77-000020-001 REV 1.1 | INK: FOLD
T emergency signal T
The PANIC2 enough to be stored in a pocket or purse. accessories allow the clip location
Accessories
Use the supplied accessories
BLACK | MATERIAL: 20 LB MEAD BOND | SIZE: 5.50" X 8.50" SCALE 1:1 |
S: TRI-FOLD VERTICAL, TRI-FOLD HORIZONTAL (TO FIT IN BOX)
he Vivint Panic Button Remote (PANIC2) is designed to transmit an
from any location within range of the control panel.
he panel will receive signals whether the system is armed or disarmed.
device is discrete and versatile. It is small and lightweight
Additionally, the supplied
device to be worn on a lanyard, wristband, or belt
/holder; or placed in the holder that can be mounted in a fixed
(see accessory drawings).
or more details, go to the Support page at: Vivint.com, and the KIM site at: corp.vivint.com/sites/KIM/)
The PANIC2 device can be programmed as a supervised or non-supervised device. If supervised, the
device should always stay within range of the panel.
The device can be programmed to contact emergency services with either an audible or silent alarm.
to carry or mount the PANIC2 device.
Battery Installation
The battery should last 3 notification will be indicated on the control panel.
*The battery may fit loose in the battery holder, but the cover will hold it sec urely in place.
FCC and Industry Canada Regulatory Declarations*
CAUTION:
This device has been tes ted and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rule license
These limits a re designed to pr and can radiate radio fre quency energy and communications. However, there is no gua rantee that interference w ill not occur in a particu lar installation. If t his equipme inter the interference by one o r more of the following measures:
PRUDENCE
Conformément à la réglem entation d'Industrie Canada, le présent ém etteur radio peut fonctionner avec une antenne d'un type et (ou utilisateurs, il faut cho isir le type d'antenne et son gain de so rte que la puissance isotrope rayonnée é qui nécessaire à l'établiss ement d'une communication satisfaisante. Le présent appareil es t conforme aux CNR d’Industrie Canada applicable s aux appareils radio exempts de licence. L ’exploitatio
eux conditions su ivantes: (1) l’appareil ne doit pas produire de brou illage, et (2) l’utilisat eur de l’appareil doit a ccepter tou même si le brou illage est susceptible d’e n compromettre le fonctio nnement. Ces limites s ont
quipement génère, utilise et peut émettre une énergie de radiofréquence et, s'il n'est pas installé et utilisé conformément aux ins interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des inte rférences no se produiro installation pa rticulière. Si cet équipem ent provoque des inter férences nuisibles à l mettant l'équipement hors e t sous tension, l'utilisateur est encourag é à essayer de corriger l'interférence pa r une ou plusieurs des mesures suivantes:
FCC ID:
*For more compliance and warranty information, vis it:
Batteries must not be recharged, disassembled or disposed of
recovery and re cycling regulations in you r area. Keep away from s mall children. If batte ries are swallowed,
California Only:
special handling may app ly.
© 2014 Vivint Inc. All Rights Reserved. | www.vivint.com | M/N: PB01 | Doc P/N: 77-000020-001 Rev. 1.1
Wireless Product Notice
Wireless communications hardware provides reliable communication;
Wireless signals may be blocked by radio signals that occur on or near the wireless operating frequencies.
1. Remove the cover by inserting a coin in the slot and twisting gently.
2. Place a small flathead screwdriver in the slot between the metal clip and battery
and pry the battery up and out of the battery holder.
3. Insert the replacement battery with the + sign facing out.*
4. Replace the sensor cover.
5. Verify the device is functioning properly.
WARNING! The polarity of the battery must be observed (as shown in the image). Improper handling of lithium batteries may result
in heat generation, explosion, or fire, which may lead to personal injury. Replace only with the same or equivalent battery type as recommended by the manufacturer.
AVERTISSEMENT! La polarité de la batterie doit être observée (comme indiqué dans l'image). Une mauvaise manipulation des piles
au lithium peut conduire à la production de chaleur, une explosion ou un incendie, ce qui peut entraîner des blessures. Remplacez-le par le même type ou équivalent de la batterie tel que recommandé par le fabricant.
This Perchlorat e warning applies ONLY to M anganese Dioxide Lithium c ells sold or distributed in California, USA. Perchlo rate material
The transmitters are required to compl y with all applicable wireless rules and regulations. As such, they have limited
transmitter power and limited range.
-5 years under normal use. If the battery is low, a low battery To replace the battery,
in fire. Disposa l of used batteries must be made in accordance with the waste
promptly see a doctor.
(For more inform ation, visit: www.dtsc.ca.gov/hazardouswaste/perchlorate)
however, the re are limitations which must be observed.
Unauthorized changes or modifications could void the user’s authority to operate the equipment.
-exempt RSS standard(s ). Operation is subject to the following t wo conditions: (1) This device may not cause harmful interference, and (2) This device must ac cept any interference received, including inte rference that may cause undesired operatio n of the device.
ference to radio or te levision reception, which can be determine d by turning the equipment off and on, t he user is encouraged to try to correct
• Reorient or relocate the receiving antenna.
• Increase the sepa ration between the equipment and the receiv er.
Connect the equipment into an outlet on a ci rcuit different from that to which the rece iver is connected.
• Consult the dealer or an experienced radio/television technician for help.
: Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées.
inférieur) app rouvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risque s de brouillage radioélect rique à l'intention des autres
conçues pour fournir une protection raisonnable contre les inter férences nuisibles dans une installatio n résidentielle. Cet é
• Réorienter ou déplacer l'antenne de réception.
• Augmentez la distance entre l'équipement et le récepteur.
Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est bran ché.
Consulter le rev endeur ou un technicien radio / télévision expé rimenté pour de l'aide.
2AAAS-PB01 , IC ID: 10941A-PB01
ovide reasonab le protection against harm ful interference in a res idential installation. T his equipment generates, uses ,
, if not installed and us ed in accordance with the instructions, may ca use harmful interference to radio
a réception radio ou télévision, ce qui peut être déterminé en
www.vivint.com
s and Industry Canada (IC)
nt does cause harmfu l
d'un gain maximal
valente (p.i.r.e. ) ne dépasse pas l'intensité
n est autorisée aux d
t brouillage radioélectrique subi,
tructions, il peut causer des
nt pas dans une
Loading...