Door/Window Contact
(V-DW11-345)
Quick Reference
Programming Instructions
(
Loop 2 (default): Use when the magnet is used directly with the sensor.
Installer Test
Once installed, open and
transmit to the Vivint Control Panel while the panel is in installer test mode.
User Test
Open and/or close
correctly to the panel. The panel should recognize the state change of the object that is being monitored.
Specifications
Wireless Signal Range
350 feet (106.7 m), open air
Battery
Panasonic CR2032 or equivalent lithium battery
Transmitter Frequency
345 MHz
Code Outputs
Open, Close, Tamper, Low Battery, Loss of Supervision
Supervisory Interval
70 minutes per signal (12 hours for panel to report supervision failure)
Operating Temperature Limits
32° to 120°F (0° to 49°C)
Relative Humidity
5-95% Non-Condensing
PRINT INSTRUCTIONS: REFERENCE SHEET V-DW11-345 P/N 77-000002-001 REV 1.1 |
INK:
FOLD
For external switch usage:
(store excess wire in the device).
Installation Instructions
For internal switch usage:
flathead screwdriver and replace it with the spacer back.
T
on doors, windows, and other objects in order to monitor open and closed states.
The DW11 transmits a signal to the
or close to,
The DW11 device has an external input for NC (Normally Closed) dry contact
devices, or it can be used with the supplied magnet directly
The DW11 is also equipped with a cover tamper for additional security.
BLACK | MATERIAL: 20 LB MEAD BOND | SIZE: 5.50" X 8.50" SCALE 1:1 |
S: TRI-FOLD VERTICAL, TRI-FOLD HORIZONTAL (TO FIT IN BOX)
he Vivint Door/Window Contact (DW11) is a sensor device that can be installed
panel when the magnet is moved away from,
the DW11 sensor.
with the sensor.
For more details, go to the Support page at: Vivint.com, and the KIM site at: corp.vivint.com/sites/KIM/)
• Loop 1: Use when the external input is used.
•
1. Secure the sensor to the door or window frame, or other object, using
the supplied adhesive or screws.
NOTE: It is recommended to install the sensor on the side that
will be moving less (e.g. the doorframe instead of the door).
2. Secure the included magnet adjacent to the sensor on the door,
window, or other object using the supplied adhesive or screws.
NOTE: If necessary, use the supplied magnet spacer to better align the
magnet and sensor. Remove the back from the magnet using a small
1. Secure the external contact switch in the desired location.
2. If necessary, drill a hole to allow the external contact wires to reach
the desired location of the sensor.
3. Feed the wires through the drilled hole and then through the access
hole in the back of the sensor.
4. Connect the wires into the NC dry contact connector.
NOTE: With solid-core wire you should be able to push the wire
directly into the connector. Press the small button on the connector to
release the wire.
5. Mount the sensor in the desired location and reattach the sensor cover
/or close the door or window for which the DW11 is installed so that the sensor will
the door or window for which the DW11 is installed to ensure the sensor is transmitting
Battery Installation
To replace ba ttery, insert coin into the top slot and gently twist until the cover
replacement batteries (see Specifications).
FCC and Industry Canada Regulatory Declarations*
CAUTION:
This device has been tes ted and found to comply with the limits for a Class B digital device,
license
These limits a re designed to provide rea sonable protection agains t harmful interference in a residential installati on. This e
and can radiate radio fre quency
communications. However, there is no gua rantee that interference w ill not occur in a particu lar installation. If t his equipme
interference to radio or t elevision reception, which can be determi ned by turning the equipment off and on, the user is encou
the interference by one o r more of the following measures:
PRUDE
Conformément à la réglem entation d'Industrie Canada, le présent ém etteur radio peut fonctionner avec une antenne d'un type et
(ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risq ues de brouillage radioé lectriqu
utilisateurs, il faut cho isir le type d'antenne et son gain de so rte que la puissance isotrope ra
nécessaire à l'établiss ement d'une communication satisfaisante.
Le présent appareil es t conforme aux CNR d’Industrie Canada applicable s aux appareils radio exempts de licence. L ’exploitatio
risée aux deux
conditions su ivantes:
fonctionnement.
Ces limites sont conçues pour fournir une protection raisonnable c ontre les interférences nuisibles dans une installation résidentielle. Cet équipement
génère, utilise et peut émettre une énergie de radiofréquence et, s'il n'est pas installé et utilisé con
interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des inte rférences no se produiro
installation pa rticulière. Si cet équipem ent provoque des inter féren
mettant l'équipement hors e t sous tension, l'utilisateur est encourag é à essayer de corriger l'interférence pa r une ou plusieurs des mesures suivantes:
Consulter le revendeur ou un technicien r
FCC ID:
IC ID:
*For more compliance a nd warranty informatio n, visit: www.vivint.com
Batteries must not be recharged, disassembled or disposed of in fire.
with the waste recovery and recycling regulations in your a
promptly
California Only:
www.dtsc.ca.gov/hazardouswaste/perchlorate
© 2014 Vivint Inc. All Rights Reserved. | www.vivint.com | M/N: DW02 | Doc P/N: 77-000002-001 Rev. 1.1
Wireless Product Notice
Wireless communications hardware provides reliable communication; however, there are limitations which must be observed.
• Wireless signals may be blocked by radio signals that occur on or near their operating frequencies.
releases. Use only the recommended
WARNING! The polarity of the battery must be observed (as shown in the image). Improper handling of lithium
batteries may result in heat generation, explosion, or fire, which may lea d to personal injury. Replace only with
the same or equivalent battery type as recommended by the manufacturer.
AVERTISSEMENT! La polarité de la batterie doit être observée (comme indiqué dans l'image). Une mauvaise
manipulation des piles au lithium peut conduire à la production de chaleur, une explosion ou un incendie, ce qui
peut entraîner des blessures. Remplacez-le par le même type ou équivalent de la batterie tel qu e recommandé
par le fabricant.
Disposal of used batteries must be made in accordance
rea. Keep awa y from small childre n. If batteries are swallowed,
see a doctor.
Perchlorate material special ha ndling may apply. (For more information, visit:
)
• The transmitters are re quired to comply with all applicable wireless rules and regulations. As such, they have limited
transmitter power and l imited range.
Unauthorized changes or modifications could void the user’s authority to operate the equipment.
-exempt RSS standard(s ). Operation is subject to the following t wo conditions:
(1) This device may not cause harmful interference, and
(2) This device must ac cept any interference received, including inte rference that may cause undesired operatio n of the device.
energy and, if not insta lled and used in a ccordance with the instructions, may caus e harmful interference to radio
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
NCE! Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées.
(1) l’appareil ne doit pa s produire de brouillage, et
(2) l’utilisa teur de l’appareil doit ac cepter tout brouillage ra dioélectrique subi, même s i le brouillage est s usceptible d’en compromett re le
• Réorienter ou dé placer l'antenne de réce ption.
• Augmentez la distance entre l'équipement et le récepteur.
• Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est bran ché.
adio / télé vision expérimenté pour de l'aide.
2AAAS-DW02
10941A-DW02
ces nuisible s à la réception radio ou t élévision, ce qui peut ê tre déterminé en
pursuant to Part 15 of FCC Rules and Industry Canada
yonnée équivalente (p. i.r.e.) ne dépasse pas l'intensité
quipment generates, uses ,
nt does cause harm ful
raged to try to correct
d'un gain maximal
e à l'intention des a utres
n est auto
formément aux instruct ions, il peut causer des
nt pas dans une
Loading...