Vitus Audio RI-100 Owner's Manual
RI-100
Owner’s Manual
2
RI-100 | Version 1
3
RI-100 | Version 1
All rights reserved. No part
of this publication may be
reproduced, stored in or
introduced into a retrieval
system, or transmitted in
any form, or by any means
(electronic, mechanical,
photocopying, recording
or otherwise) without the
prior written permission of
Vitus Audio. Any person who
does any unauthorized act
in relation to this publication
may be liable to criminal
prosecution and civil claims for
damages.
Information contained in this
manual is subject to change
without notice, and whilst it
is checked for accuracy, no
liabilities can be accepted for
errors.
4
RI-100 | Version 1
5
RI-100 | Version 1
table of contents
on a personal note
Certificate . . . . . . . . . . . . 6
from the creator
Foreword . . . . . . . . . . . . . 7
introduction
About this manual . . . . . . . . 8
Introduction to the Reference Se-
ries . . . . . . . . . . . . . . . . . 8
1. getting started
Unpacking the box . . . . . . . . 10
What’s in the box . . . . . . . . . 10
Device overview . . . . . . . . .11
The topology of the volume con-
trol. . . . . . . . . . . . . . . . .12
2. connecting
Turning the RI-100 on and off. . . 13
RI-100 rear panel . . . . . . . . . 14
Connecting the RI-100 . . . . . . 14
3. operation
Operation modes . . . . . . . .16
Functions – left front panel . . .18
Functions – right front panel . .19
The menu structure . . . . . . .20
Discription of the elements
in the menu. . . . . . . . . 22
The menu structure . . . . . . .23
4. operation & service
Safety notice . . . . . . . . . . . 24
Mains supply voltage . . . . . .24
Maintenance . . . . . . . . . . . 24
Mains fuse . . . . . . . . . . . .25
Replacing a blown fuse . . . . .26
5. warranty
Warranty . . . . . . . . . . . . .28
6. specifications
RI-100 Specifications . . . . . . . 31
Load values of the RIAA Module. 32
7. examples operation
Example 1 . . . . . . . . . . . .33
Example 2 . . . . . . . . . . . .34
Example 3 . . . . . . . . . . . .35
Example 4 . . . . . . . . . . . .36
Example 5 . . . . . . . . . . . .37
Example 6 . . . . . . . . . . . .38
Example 7 . . . . . . . . . . . .39
Example 8 . . . . . . . . . . . .40
Example 9 . . . . . . . . . . . . . 41
Example 10 . . . . . . . . . . . . 42
Example 11 . . . . . . . . . . . . 43
Example 12 . . . . . . . . . . . . 44
Example 13 . . . . . . . . . . . . 45
7. examples connecting
devices
Connecting devices . . . . . . . 46
Connecting devices 1 . . . . . .47
Connecting devices 2 . . . . . .48
Connecting devices 3 . . . . . .49
8. pictures
RI-100 Inside view . . . . . . . .50
RI-100 Front . . . . . . . . . . . . 51
6
RI-100 | Version 1
on a personal note
Certificate
Model: RI-100
Product ID/Serial
__________________________________
Product Build Date
__________________________________
Signed
__________________________________
All products details, specifications and
measurements are recorded for your RI-100
and kept by Vitus Audio.
7
RI-100 | Version 1
from the creator
Foreword
First of all, thank you for
choosing the Vitus Audio
RI-100 integrated amplifier,
we are sure you will enjoy it
for many years to come. When
purchasing a Vitus Audio
product, you are guaranteed a
musical performance,
which exceeds the current
musical standards. Vitus
Audio is dedicated to musical
performance rather than
technical details and high
performance measures.
We believe that many
manufactures are blinded by
the current available theory,
instead of looking for new
answers.
At Vitus Audio everything
works until proven not to.
This way we always try to
push the limits and explore
the unexplored. As a result
of this, many of the solutions
we use today are considered
to be “impossible to ever
get working”,however they
have convinced many people
and reviewers world wide
of the opposite. Before any
of our new topologies are
implemented in our products,
they are carefully reviewed by
our dedicated listening panel.
This way we can guarantee
the correct level of musically
performance and robustness.
Generally we’re after super
neutral, super detailed and
super dynamic reproduction
without “loosing” the nerve
in the music which often is
a drawback of many high
end amplifiers. Our real
strongholds are complete
silence, unbelievable depth
and width in the soundstage
resulting in a far more open
sound with higher resolution
-you could say, closer to the
artist. As a result of the above,
our amps do not “focus” on
any specific frequencies - i.e.
no extension of top or bas,
which of course results in high
clarity of the midrange since
it’s “naturally present”!
Hans Ole Vitus
8
RI-100 | Version 1
introduction
About this manual
This is your RI-100 owner’s
manual. The following pages
will describe, as clearly as
possible, how to get your RI100 operating fast and simple.
Although some operations are
self-explanatory, we strongly
suggest you read this manual
to avoid any damage to the
unit. The manual is designed
to be helpful. If there are
points you feel we could cover
better, or that we have missed
out – please tell us.
Important
information is
presented like
this. Ignoring this
information may cause
damage to you or the
unit. Damage coused
to the unit by ignoring
this information might
invalidate the warranty.
Introduction to the
Reference Series
The Vitus Audio Reference
Series is a true high-end series
of products, which is build on
our true dedication to neutral
music reproduction. Every
detail is carefully thought
through, and all choices made
during development, where
based purely on listening, and
not measuring. Only the best
available materials are used to
ensure an overall quality which
will last for many years, when
treated right.
9
RI-100 | Version 1
introduction
This amplifier is
VERY heavy –
make sure to be
at least two people to
unpack the unit. You
might damage both
your back and the
amplifier if extra care
is not applied. Vitus
Audio A/S cannot
be held responsible
for any damage that
is a consequence of
uncareful handling of
the unit.
Figure 1 Box exploded view
Foam top 1
Foam bottom
Box
Foam top 2
Foam Sides
6 pieces
RI-100
Brochure
Manual
Power Cable
Mac Remote
10
RI-100 | Version 1
Unpacking the box
After you have opened the
top, it is possible to remove
the top protective foam which
gives you direct access to the
amplifier. In the top you will
find the remote, the power
cord and brochures. Now
remove the side protective
foam, this will make it easier
to grab hold of the RI-100.
Two people carefully lift the
amplifier out of the box, and
put it directly onto the floor.
Store the empty box and the
protective foam for later use.
What’s in the box
Foam top 1
Vitus Audio Brochure
RI-100 Manual
Mac Remote
Power Cable
Foam top 2
Foam Sides 6 pieces
RI-100
Foam bottom
Box
1. getting started
Device overview
Front panel: Anodized Aluminium
Body: Powder coated Aluminium
Total weight: 40 KG
Figure 2 Device overview
11
RI-100 | Version 1
1. getting started
1. getting started
165 mm
180 mm
165 mm
435 mm
435 mm
35 mm
12
RI-100 | Version 1
1. getting started
The topology of the volume
control used in the RI-100 is
very different compared to the
“standard”. The RI-100 uses a
series of fixed resistor networks
to control the volume. Relays
are used to switch between the
resistor networks. Across all
volume steps, a fixed resistor
is in series with the signal
path. This gives the best performance possible. When you
change volume, a different
number of shunt resistors are
used.
To prevent pop in the output,
we have chosen to first add
the new shunt resistors, and
then wait a short time, before
removing the unused shunt
resistors at the new volume
step. This will give a minor fall
in volume before settling at
the new volume step. It takes
only very little time to get
used to this type of operation
of the volume, and it will give
you superior sound quality
over the traditional digital and
analogue potentiometers.
The topology of the
volume control.
13
RI-100 | Version 1
2. connecting
2. connecting
Turning the RI-100 on and off.
Always turn on the products beginning from the source:
CD player a pre-amplifier a power amplifier.
Always turn off your products in reverse order:
Power amplifier a pre-amplifier a CD player.
Not following this procedure,
may cause damage to any of
your products/speakers.
Damage caused to any of your
products/speakers by not following
this procedure will invalidate the warranty.
RI-100 rear panel
Outputs
Speaker left
Speaker right
Ground/Earth
Preout. XLR
Optional Headamp
Inputs.
Input 1,2,3. XLR
Input 4,5. RCA
RIAA (optional ) Input 5
Power
Optional DAC interface
Figure 4 Plugs
Speaker out
Speaker out
Ground
XLR out
Jack
XLR out
RCA
RCA
Power
XLR in
XLR in
USB b (male)
14
RI-100 | Version 1
2. connecting
Connecting the RI-100
Place the RI-100 on its shelf.
Connect all the sources to the
inputs of the RI-100, (labelled
INPUT 1 to 5 on the rear
panel.)
Connect the Speaker output of
the RI-100. Carefully connect
the mains to the amplifier,
after you have connected both
inputs and outputs.
This is a true balanced
amplifier, DO NOT connect
the ”
-
“output (Figure 3) to
any ground source, including
chassis or signal ground, this
will damage the amplifier.
The pre-out connectors can be
connected to a power amplifier
for biamping or an active sub.
Figure 3 ”
-
“output
Figure 5 RI-100 Rear panel.
GND / EARTH
Input 4 Input 5 / RIAA Input 5 / RIAA Input 4
Input 2 Input 3Input 1 Input 2 Input 1Input 3
+
-
This is a true balanced
poweramplier. DO NOT
under any circumstance
connect (-) speaker output
to ground.
Caution
+
-
This is a true balanced
poweramplier. DO NOT
under any circumstance
connect (-) speaker output
to ground.
Caution
Optional DAC interface
Optional Headamp interface
Use this connection with care
Connecting it to other units
with impropper GND may
damage this unit. Such
damage will not be covered
by warranty!
Caution
Preout
Preout
NEUTRIK
PUSH
NEUTRIK
PUSH
NEUTRIK
PUSH
NEUTRIK
PUSH
NEUTRIK
PUSH
NEUTRIK
PUSH
MAINS
Speaker out
Ground
XLR out
XLR out
Jack
RCA
Power
XLR in
XLR in
USB b (male)
15
RI-100 | Version 1
2. connecting
2. connecting
Fuse
16
RI-100 | Version 1
3. operation
Figure 6 RI-100 Front panel.
Operation modes
Loading...