Vitrex LRS600IND User Manual

User Manual

Long Reach Sander

LRS600 (230v)

LRS600IND (110v)

&

Page 1 of 8

LRS600IND

LRS600

110v

230v

PRODUCT DESCRIPTION

The machine is designed for sanding drywalls, ceilings and walls of the inner and outer surfaces,
clearing the floor residues, paint coatings, adhesive and loose plaster etc.

Our machine is not suitable for processing the object containing asbestos.

You must abide by certain safety precautions when using the equipment.

In order to prevent injuries and damages from occurring, you must always read through this
operating manual carefully.

This manual must be kept in a safe place so that the information that it contains is always available. This
operating manual must accompany the equipment if it is transferred to somebody else.

We do not accept any liability for accidents or damage arising from ignoring this manual and the safety
instructions.

SPECIFICATIONS

Model No.

Power 600W 600W

Speed 0-1000 /min 0-1000 /min

Grinding pad diameter 215mm 215mm

Sandpaper diameter 225mm 225mm

Tube diameter 32mm 32mm

Short-length
(Without additional tube)

1.23 /1.65m

1.23 /1.65m

Long Length
(With additional tube)

2.20m

2.20m

Short-weight 4.5 kg 4.5 kg

Long Weight 5.0 kg 5.0 kg

Voltage

3. SAFETY INSTRUCTIONS

The following pictograms appear throughout these operating instructions:

Indicates danger of injury, risk to life and possible damage to the appliance if these instructions

are not followed.

Indicates the presence of electric shocks.

• Read through these operating instructions carefully before using the appliance.

• Become familiar with the functions and method of operation.

• To ensure proper operation, always maintain the appliance according to the instructions.

• The operating instructions and associated documents should always be kept close to the appliance.

When using power tools, you must observe the following basic safety precautions in order to ensure protection
from electric shocks, injury and fire. Read and follow all the instructions before using this power tool.

Page 2 of 8

Always check if your mains voltage corresponds with the value on the type plate

The machine has been double-insulated in accordance with EN60745: therefore, an earth wire
is not necessary

USE CORRECT SUPPLY VOLTAGE: The power supply voltage must match the information quoted on the
tools identification plate. Use of an approved RCD circuit breaker between the machine and the electrical
power point is highly recommended.

USE PROPER EXTENSION CORD: Only use an approved extension cable that is suitable for the machine's
power. The cord must have a diameter of at least 1.5mm2.When the extension cable is on a reel, unroll the cable
in its entirety.

SWITCH OFF THE MACHINE IMMEDIATELY IN CASE OF:

1. Malfunction in the mains plug, power cable or damaging of cable.

2. Broken switch.

3. Smoke or smell of burning.

GENERAL SAFETY RULES
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions

may result in electric shock, fire and/or serious injury.

Work area safety

a) Keep work area clean and well lit.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases
or dust.
c) Keep children and bystanders away while operating a power tool.

Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed power tools.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply.

Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use a power tool while you are tired or under the influence of drugs, alcohol or medication.
b) Use personal protective equipment. Always wear eye protection and protective mask
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used.

Page 3 of 8