User’s Guide
DiGi Microscope
Version 1.0A
1
Content
1. Products Introduction .......................... 3
1.1 Packing Contents ......................... 3
1.2 IR remote controller .................... 3
1.3 Microscope introduction: .......... 11
1.4 Microscope focus ....................... 14
1.5 Change microscope Object lens 17
1.6 Microscope accessory................ 20
2. Install Application Program ............... 21
2.1 Insert CD to CD-ROM ................. 21
2.2 Install Application Program ....... 21
2.3 Exit Install Program .................... 21
3. Application Program Operation ......... 22
3.1 Video Preview Window ............. 23
3.2 Image Preview Window ............. 23
3.3 Main Menu ................................ 23
3.4 Main Button ............................... 23
3.5 Files List ..................................... 25
2
3.6 Function modes ......................... 25
4. Printed Notice .................................... 27
4.1 Maintenance .............................. 27
4.2 Product Specification ................. 28
4.3 Safety Instructions ..................... 29
3
1. Products Introduction
1.1 Packing Contents
There are 1 microscope and 10 accessories in the box. The Object Lens 4X is
already assembled onto microscope. If object lens needs to change, please refer to
Section 1.5.
Item
Q’ty
Item
Q’ty
DiGi Microscope
1
White Balance Card
1
HDMI Cable
1
Calibrator
1
USB 2.0 Cable
1
User’s Guide
1
Power adaptor
1
Install CD
1
S107 Stand
1
Object Lens 4x
1
Stand assemble guide
1
Object Lens 10x
Option
1.2 IR remote controller
The Digi Microscope is control by IR remote controller or application program.
When enable the far distance control mode from application program, the remote
controller is only used for Power, PC Cam or HDMI. There are 3 groups on the
remote controller to use in different mode: Common use, PC Cam and HDMI.
1.2.1 Buttons for Common use
The said buttons are used both for PC Cam and HDMI mode.
(1) Power ：Turn on/off.
(2) LED Adjustment: Adjustable 12 levels of brightness.
(2-1) Increase ：Increase LED brightness.
(2-2) Decrease ：Decrease LED brightness.
(2-3) On/Off ：Turn on or off the LED. When turn on the LED, the
brightness will return to the situation before turn off.
(3) Motor Reset (Calibrate of whole operation)：To go back to the lens
4
position. If electricity black out occurred during operation, please reset the
whole operation.
(4) Manual focus
(4-1) Zoom in ：Descending speed when press longer Zoom in.
(4-2) Zoom out ：Descending speed when press longer Zoom out.
(4-3) Step zoom in ：zoom in by steps.
(4-4) Step zoom out ：zoom out by steps.
Microscope remote controller
Buttons for common use
5
1.2.2 Buttons for PC CAM
The said buttons are only used for PC Cam mode.
(1) PC CAM ：When press the PC CAM mode, the USB cable has to connect with
PC and microscope. Please disable software before switch to HDMI mode or
turn off.
(2) Autofocus：This function only operates on PC Cam mode.
(2-1) Single Autofocus ：Only focus one time.
(2-2) Continuous autofocus ：Re-focus until the image is clear.
Buttons for PC CAM mode
Buttons for HDMI mode
6
(3) Snapshot ：Take 5M picture and delivery to Application program.
1.2.3 Buttons for HDMI
The said buttons are only used for HDMI mode.
(1) HDMI ：When press HDMI mode, the HDMI cable has to connect with
screen and microscope.
(2) Menu on Screen ：Open/close menu for setting.
(2-1) BRIGHTNESS：To adjust the brightness of whole image. [1~31]
(2-2) CONTRAST：To emphasis the difference between bright and dark. [1~31]
(2-3) SATURATION：To adjust the color level. [1~31]
(2-4) EXPOSURE VALUE：On/Off the exposure [ON/OFF]。
[ON] Auto mode, use with exposure value +/-. The adjust method
please refer to Section 1.2.3-(7). This mode will adjust the image
brightness automatically. Please turn on all LED to keep the best
observation.
[OFF] Manual mode, use with LED brightness +/-. The adjust method
please refer to Section 1.2.1-(2) and Section 1.2.3-(7). This mode
7
inquires to adjust LED brightness and exposure value +/-. The image
brightness will change as the LED brightness and exposure value
changed.
(2-5) SHARPNESS：On/Off the sharpness. [ON/OFF]。
[ON] the image is sharp.
[OFF]the image is less-sharp, but more smooth.
(2-6) STATUS BAR：Show or not show the status bar on the screen top. please
refer to Section 1.2.3-(9).
[ON] show the status bar on the top of screen.
[OFF]close the status bar show on the screen.
(2-7) OBJECT LENS：Object lens type. (4x or 10x) When change another lens,
the setting needs to reset. Refer to Section 1.5.
[4X] Object Lens 4x, turn on LED for lens 4x; in opposite, turn off LED
for lens 10x.
[10X]Object Lens 10x, turn off LED for lens 4x; in opposite, turn on LED
for lens 10x.
(2-8) LCD SIZE：Screen size. The current setting is only for 7”~80”.
(2-9) FACTORY：All setting return to factory setting.
[NO]the current setting.
[YES]return to factory setting.
(3) Up ：choose last item
(4) Down ：choose next item
(5) Left ：choose next value
(6) Right ：choose last value
(7) Exposure Value: 13 levels of exposure value is selectable, from +0.2~-2.0.
(7-1) Increase ：when the image is darker, add exposure value.
(7-2) Decrease ：when the image is brighter, decrease exposure value.
8
(8) Video Ratio ：Choose image ratio or Field of View. There are 3 types of
video ratio, press the button to next ratio.
(8-1) 4/3F：4:3 means the image is from 5M image (2592*1944) output to fit
4:3 screen size. (The screen image: 1440*1080). Proportionally reduce
the input image height to fit the screen.
(8-2) 16/9S：16:9S means the image from 5M (2592*1944) output to 16:9
screen size (the screen image: 1920*1080). Reduce input image
horizontal proportionally to fit the screen, but trim the height.
(Scaling) Magnification size becomes higher.
9
(8-3) 16/9C：16:9C means the image from 5M (2592*1944) output to 16:9
screen size (the screen image: 1920*1080). Crop image (1920*1080)
from input image 5M (2595*1944); therefore, FOV become smaller,
magnification become higher.
(9) Status Bar : On/Off to show or not show the status bar. Each color
represents different information.
10
(9-1) ZOOM：Zoom path, total 15 sections.
(9-2) FOV：Field of View, display image on the effective horizontal size of screen.
(9-3) M：Magnification. Magnification size changes depending on lens position,
screen size, and image ratio. Please refer to Section 1.4.2.
(9-4) D：Distance, means the distance from object lens to object.
(9-5) EV：Exposure Value, please refer to Section 1.2.3-(7).
(9-6) LED：LED Levels, please refer to Section 1.2.1-(2).
(9-7) R：Video Ratio, please refer to Section 1.2.3-(8).
(10) Auto White Balance Calibration : Place the White balance card (included in
box) under the lens, firstly focus til clear then choose On to calibrate white
balance. Sometimes the white balance is influenced by environment light
source or other light source, thus it’s suggested to calibrate white balance if
the color is not correct.
11
(11) Image Freeze : On/Off image freeze. Freeze the image, press the button
again to return to preview.
(12) Sharpness : On/Off sharpness mode. Please refer to Section 1.2.3-(2).
1.3 Microscope introduction:
1.3.1 IR Remote area/Indicator
When both HDMI and USB indicator light on means the microscope is turn off.
(1) IR remote control aiming area ○
a
(2) HDMI indicator○
b
: When light up means HDMI mode.
(3) USB indicator○
c
: When light up means USB mode. Light flicker means
microscope does not connect with PC.
○b
○c
○a
12
1.3.2 Power/USB/HDMI port
(1) Power○
d
: Please only use the power supplier from the box, do not use any
other power supplier.
(2) USB○
e
: USB port for connecting application program. When using PC Cam
mode, please connect the microscope to PC by using the USB cable from the
box. (firstly to connect USB cable to microscope and PC then secondly switch
to PC Cam mode)
○e
○d
13
(3) HDMI○
f
：HDMI port for connecting screen. When using HDMI mode, please
connect the microscope to screen by using the HDMI cable from the box.
*Note: if connect with TV screen, please choose the homologous image ratio
and format.
1.3.3 Stand gear box
The universal joint as ○g. Firstly, assemble the stand then screw microscope to the
universal joint on gear box and fixed on stand.
○g
○f
14
1.3.4 LED/ Light socket
(1) LED○
h
: Luminance for object lens 4x, total 30pcs LEDs with angle. 6pcs as fig
have wider angle for purpose.
(2) Light socket○
i
: Luminance for object lens 10x.
1.4 Microscope focus
There are two ways to focus. First, to choose focus distance to adjust the
microscope height, then tuning focus by remote controller until clear. On the
contrary, first to choose the image sensor position then adjusts the microscope
height.
Focus distance: distance from object lens to object.
Image sensor position: The image sensor position.
1.4.1 Way of Focus
(1) Fixed focus distance
Use knob ○
j
or ○
k
to adjust the distance from object lens to object. When
the distance is closer, the magnification size is higher. When fixed the focus
distance, using remote controller or far distance control mode on application
○i
○h
15
program to tuning to clear image.
(2) Fixed image sensor position
(2-1) In HDMI mode, the status bar will show on the screen, please refer to
Section 1.2.3-(9). Use remote controller to adjust image sensor position
based on magnification size, FOV, or distance height.
(2-2) In PC CAM mode, choose required height or FOV from drop down list on
application program (see below fig).
When image sensor position is fixed, as (2-1) and (2-2), use knob ○j & ○k to
find clear image. Adjust the knob ○j in the beginning to the appropriate
height, then slightly adjust the knob ○k to find clear image.
○j
○k
○j
○k
16
1.4.2 Magnification chart
15 image sensor positions had set from the whole area, the image sensor
position tells the magnification size, field of view, or height. The below
chart is measured on 21.5” screen, it’s only a reference data, might not be
accurate enough. Based on the image ratio, field of view and magnification
size will change. Please refer to “F”, “S”, “C” in Section 1.2.3 – (8).
(1) Object lens 4X, focus distance from 1.95cm to 22cm (0.767 to 8.66inch).
Object lens 4X on 21.5” screen
1 2 3 4 5 6 7
8
Distance
22.0
15.2
9.70
7.35
5.75
4.75
4.15
3.65
F, S FOV
27.0
18.4
11.9
9.02
7.10
5.88
5.05
4.40
C FOV
19.9
13.6
8.80
6.67
5.25
4.35
3.73
3.25
F Magnification
13
20
30
40
50
61
71
81
S Magnification
17
26
40
53
67
81
95
109
23
34
54
70
90
109
127
145
9
10
11
12
13
14
15
unit
Distance
3.30
2.85
2.65
2.45
2.30
2.10
1.95
cm
F,S FOV
3.91
3.50
3.19
2.91
2.68
2.48
2.34
mm
C FOV
2.89
2.59
2.36
2.15
1.98
1.83
1.73
mm
F Magnification
92
102
112
123
134
145
154
X
S Magnification
122
137
150
164
179
193
205
X
165
183
201
221
241
261
277
X
17
(2) Object lens 10X, focus distance from 4.5mm to 7.7mm (0.177 to 0.303inch.
1.5 Change microscope Object lens
Object lens 10x is optional accessory. It comes with luminance, thus power
supplier is needed. Please remove the power cable before change object lens.
1.5.1 Remove LED cover ○
l
Unscrew 3 pc screws to remove LED cover.
Object lens 10X on 21.5” screen
Sensor position
1 2 3 4 5 6 7
8
Distance
7.70
7.10
6.70
6.40
6.10
5.89
5.60
5.41
F,S FOV
1.39
1.30
1.21
1.14
1.07
1.01
0.96
0.91
C FOV
1.02
0.96
0.89
0.84
0.79
0.74
0.71
0.67
F Magnification
260
279
297
318
336
360
378
395
S Magnification
346
371
395
423
447
479
503
526
468
502
534
572
604
648
680
711
Sensor position
9
10
11
12
13
14
15
unit
Distance
5.27
5.10
4.96
4.84
4.73
4.62
4.51
mm
F,S FOV
0.87
0.83
0.79
0.76
0.73
0.70
0.68
mm
C FOV
0.64
0.61
0.58
0.56
0.54
0.52
0.50
mm
F Magnification
413
439
455
480
493
145
154
X
S Magnification
550
585
606
639
657
694
705
X
743
790
819
964
887
937
952
X
18
1.5.2 Connect power cable
Plug in the power cable○m onto LED board socket○n. Pass through the
power cable out of LED cover○
o
. When remove, please never pull and drag
the power cable from inappropriate force, and hold the cable thread when
disassemble.
○m
○n
○o
○l
19
1.5.3 Assemble LED cover
After power cable plugged onto LED board, grip the other head of power
cable ○
p
and screw the LED cover ○q back.
1.5.4 Change object lens
Remove the original object lens ○r and replace with object lens 10x ○s,
then screw lens tight. Please beware of dust into lens.
○r
○s
○q
○p
20
1.5.5 Luminance adaptor
Insert the adaptor ○t onto lens, (the 2 sockets on LED board and adaptor
needs to face the same side). And plug in the power cable ○uonto adaptor○v
for luminance. This is for first time assembling.
1.6 Microscope accessory
1.6.1 Calibrator
Mainly use to calibrate the scale on application program, please refer to AP manual for
more information. The calibrator is transparent, it can apply onto object directly.
1.6.2 White balance card
The white side is use for calibrate white balance. If the object is tiny, place
the object onto white balance card (black/white side). Move the card to find
focus spot instead of move the object.
○u
○t
○v
21
2.2
2.3
2. Install Application Program
Please refer to the install manual inside CD for more details about install
application program. (User's Manual \English\Install manual.pdf) There are 4 steps
to install ap:
2.1 Insert CD to CD-ROM. (Step 1)
Insert the CD (included in the box) into CD-Rom. Install program shall run
automatically and pop out window as below:
If the install program does not pop
out, please open the CD folder and select
“Autorun.exe”. Autorun fig show as
below.
If the CD is missing or damaging,
please download from
http://www.vitiny.com.
2.2 Install Application Program (Step 2)
Click “Install Application program”
button (step 2).
2.3 Exit Install Program (Step 4)
When install completed, click “Exit”
to leave the install program.
22
3. Application Program Operation
The application program divided into 6 parts which is primary about AP operation.
For more details, please refer to AP manual inside CD. (User’s Manual \ English
\Microscope Application Program Operation Manual.pdf)
3.4
3.2
3.1
3.3
3.5
3.6
23
3.1 Video Preview Window
After connecting to microscope, the window will show preview images. As well
as video plays, image reviews, and special function modules will shown in this same
window.
3.2 Image Preview Window
The window is applied to display shot images, edit and process images.
3.3 Main Menu
The Main Menu of the Application Program contains the following selections:
3.3.1 File: open, save and print files.
3.3.2 Setting：includes input device, image quality, video information formats,
sources and compression, as well as automatic storage, etc.
3.3.3 Window: you can adjust sizes of video information windows and switch to the
single window model.
3.3.4 Tool: open saved file location, default file path, time lapse, convert video to
image, convert image to video..etc functions…
3.3.5 Language: selectable languages such as Chinese, simple Chinese, English,
Japanese and Germany…etc.
3.3.6 About: to show the version, copyright and other relevant information about
the Application Program.
3.4 Main Button
Main Button contains more general functions as follows:
3.4.1 Connect / Disconnect : button of connecting and disconnecting to
microscope camera. Video image will be displayed in Video Preview Window
after connection.
24
3.4.2 Snapshot : press the button to capture image from Video Preview
Window. The captured image will be displayed in Images Preview Window.
3.4.3 Save Image ：store images in Images Preview Window
3.4.4 Editor Image / Exit Editor ：to enter or quit Image Edition function.
After entering, tools of image edition are listed below Images Preview
Window as follows:
3.4.5 Delete Image ：Pressing delete Icon will delete image
3.4.6 Video Record / Stop Record : to record or stop recording video.
Recorded video will be displayed in Video Preview Window. You can set
compressed coding way by clicking and selecting “Setting->Video
Compression” in the Main Menu. The user is suggested install DivX encoder to
achieve better compression results and quality.
3.4.7 Play Video / Stop Play : to play or stop playing video. Video of
played files will be displayed in Video Preview Window. Playing tools are listed
below the preview window as follows:
3.4.8 Image Process / Exit Image Process : image processing include
reversed video, grey scale, black and white, edge detection and other basic
25
functions. After entering Image Processing model, tools will be displayed
below Images Preview Window as follows:
3.4.9 Print Image ：print images displayed in Images Preview Window.
3.4.10 Exit ：close the Application Program.
3.5 Files List
Files List is primarily applied to list all current files contained in folders. Select
BMP, JPG or AVI to view saved images/videos.
3.6 Function modes
Start and connect Application Program, the toolbars of Special Function
Modules will show below the Video Preview Window; which includes:
comparison, aming mode, image control, measurement and far distance
control mode. See below:
3.6.1 Comparison mode : observe similarity of compared images through
overlapping and half-half comparison. Before using the model, please load
the image for application of other functions. For tools of comparison model,
please refer to the following image:
26
3.6.2 Aiming mode : This mode provides 4 different aiming aids, which are
cross, scope, rectangle and circular to aim at shot objects as an auxiliary
function. Please refer to the following image for tools of the mode.
3.6.3 Video control mode : you can take the device by your left or right hand,
adjust image direction of yourself or object, as well as adjusting contrast,
brightness and exposure rate of the image. Please refer to the following
image for tools of Image Control Model.
3.6.4 Measurment mode : the mode can be used as rulers and compasses.
Further, the model can measure in the dynamic (real-time image) or static
(loaded images or frozen image) images, as well as providing various
measuring tools. Please refer to the following image for tools of
Measurement Model.
3.6.5 Device control mode ：This mode is to control the device from AP directly
without operate function button on the device. From the AP control, users
allow to photography, zoom in/out image, and brightness control…etc.
27
4. Printed Notice
Please read the following information before operate.
4.1 Maintenance
Please abide by the following items while storing or using the product:
4.1.1 Keep dry: do not place the product in a humid environment. Dry surroundings
are helpful to extend the life of the product.
4.1.2 Avoid temperature shock: temperature shock will cause internal condensation
inside the machine, for example, take the product into a warm room from
cold environment. Please put the machine inside the protection bag or
handbag in advance to prevent temperature shock, and avoid using the
machine in an environment with over-high/low temperature.
4.1.3 Avoid collision and drop: the product might go wrong by strong collision,
vibration or distortion.
4.1.4 Turn off the microscope before cutting off the power supply: do not forced
cut off the power supply.
4.1.5 Do not make face lens against strong light or sunshine for long time: Strong
light rays might degrade sensitive elements and generate white stain on the
image.
4.1.6 Handle movable LED cover and other parts carefully: do not force disassemble
USB Cable, HDMI cable or power supplier. Avoid contacting the lens since they
are subjected to damage.
4.1.7 Machine not in operation for period: please switch off power supply and
unplug power cable, and store them in a dry place with excellent ventilation.
Do not expose the machine in an environment lower than -5℃ or higher than
50℃
4.1.8 Appropriate storage: while carrying, please put the machine inside the box to
prevent it from being damaged because of collision.
28
4.2 Product Specification
CMOS Sensor
5 million pixels CMOS senor
Lens
Object lens 4X: 4/0.10,160/0.17; Object lens 10X:
10/0.25,160/0.17
Magnification
Object lens 4X:
15x~270x
; Object lens 10X:
260x~900x on 21.5”
screen
Auxiliary
source
White LED × 30pcs
DC port
Adaptor DC input
HDMI port
Output 1080P(1920*1080 Pixel) image
USB port
USB 2.0,3.0 compatible, connect with PC.
Focus control
IR remote controller/PC(application program) control
Power
supplier
adaptor
(input：DC 5.0V/2.0A input：AC 100-240V 50/60Hz)
Electric
Consumption
5V/1200mA
Size
106(L)×106(W)×152(T) mm
Weight
Host weight around 310 grams
Operation
environment
Temperature -5℃ ~ 50℃; Humidity-lower than 85% (No
Condensation)
For any change, please visit http://www.vitiny.com
29
4.3 Safety Instructions
As an electronic product, please do not use the machine in any place in which
all electronic products are prohibited or required to shut off electronic
products.
Please do not make the machine close to water source or wet since it is not
waterproof. Avoid electric shock.
Do not make the machine close to chemicals, objects with explosive hazard or
fire sources. Please switch off the product in gas station.
In case that there is foreign body, water inside the machine, the machine drops
off, or the housing is damaged, please switch off power supply and remove
power supply to avoid fire and electric shock.
Do not look steadily at auxiliary sources after switching on the host as it is
harmful to your eyes.
Please use related product accessories provided in the box for connecting. Do
not use any product in connection on your own without approval of original
factory.
Please remove power supplier from microscope if not using for period.
Do not disassemble the machine for inspection on your own. For any problem
occurred in the machine itself, please switch off the machine and then contact
us by e-mail to the following address: mltc@vitiny.com
30
ViTiny UM06 Warranty
P r o d u c t
Model no
S/L nos.
Purchase
d a t e
DD/MM/YYYY
Purchaser
T e l n o :
A d d r e s s
Email
Distributor Seal for Confirmation
( Stamp is necessary for validation of the Warranty )
※Distributor’s seal shall include name of the shop, telephone and address※
Please ask the distributor to fill in the name of the shop, address, purchase date and
other contents and seal to protect your rights and validate one-year warranty since
upon the purchase date.
Contents of Warranty: The Warranty is only provided free of charge for faults caused
by the manufacturing within one year since upon the purchase date.
Non-warranty:
1. Product appearance parts, such as outer casing, knobs and LED cover, etc
(charged spare parts are limited to one year after completing the product
manufacturing).
2. Consumption goods of the host itself, such a, LED lights and lens.
3. Product accessories and fittings, such as power supplier, USB cable, HDMI cable,
calibrator, white balance card, remote controller…etc.
Services caused by any of the following situations in the period of the warranty shall
not be provided free of charge:
1. Improper using or self (entrust any other with) disassembly, repair or refitting.
2. Any fault or damaged machine caused by act of god, lightning strike, abnormal
voltage or environmental factors, etc. Discrepancy of product serial number,
unfilled Warranty, or unreal fill-in, alteration or unidentified Warranty. Any
inspection and repair service after the period of warranty will be charged as
follows according to the situation:
(1) Service fees (including transportation fees) of product inspection.
(2) Repair fees.
(3) Fees of replaced parts
ViTiny Service Center Tel: 07-657-9551 Fax: 07-657-9561
Address: 10 F., No.1, Section 1, Syuecheng Road, Dashu District, Kaohsiung City 840,
Taiwan (R.O.C.)
Website: http://www.vitiny.com
HTTP://WWW.VITINY.COM
© MicroLinks Technology Corp. All rights reserve
Loading...