VT-PIRC2/H
Color PIR Cameras
VITEK
• 1/3” Sony High Density CCD (960H) with 700 TV Lines
• Minimum Illumination of 0.2 Lux / 0.1 Lux
• Pinhole 3.7mm / F2.0 Lens Included
• NC/N/NO Alarm Output
• Working 100’ Motion Detection Using 58 Beams Within 3
layers (35’ x 35’ Coverage Area)
PIR BOARD LAYOUT
1. LED: When an intrusion is detected, the LED will activate.
2. JP1: Pulse count setting.
1-2 short: Relay will activate when an intrusion is detected once. (For stable
environments or high risk operating environments)
2-3 short: Relay will activate when an intrusion is detected twice within 15 seconds.
(For harsh environments)
3. JP2: Relay output select.
Short: For outer control used in area where DC12V is requested (Limited at 200mA).
Normal: N.C. = DC12V out
Activate: N.O. = DC12V out
Open: Normal relay connector (1.5A at DC24V/1.5A at AC120V/1A at AC240V)
Normal: C & N.C. short / C & N.O. open.
Activate: C & N.C. open / C & N.O. short.
Caution! Risk of electric shock. Set-up and operation should be performed by
Authorized Service Person only.
4. VR1: Sensitivity adjustment.
Turn clockwise for high sensitivity, turn counter-clockwise for low.
5. VR2: Relay activation time adjustment (range about 2 ~ 30 seconds).
Turn clockwise for short time, turn counter-clockwise for long.
6. NC/C/NO Wiring:
C: BLACK NO: WHITE NC: YELLOW
CN1 Connector:
1. DC 12V IN
2. GND
3. AUDIO OUT (option)
4. GND
5. VIDEO OUT
6. RELAY C. (common)
7. RELAY N.O. (normal open)
8. RELAY N.C. (normal close)
CN2 Connector:
1. AUDIO IN (Not Available In US)
2. VIDEO IN (from CCD MODULE)
3. GND
4. DC 12V/120mA OUT (for CCD MODULE)
2
SPECIFICATIONS VT-PIRC2/H
Image Device
Effective Pixels
Resolution
Minimum Illumination
S/N Ratio
Electronic Shutter
AGC
Sync. Mode
Scanning System
Gamma Correction
Sync. Frequency
Video Output
Power Source
Power Consumption
Operation Temp.
Standard Lens
Dimensions
1/3” Sony High Density CCD (960H)
1020 x 508
700 TV Lines
0.1 Lux
More Than 48dB
1/60 to 1/100,000 sec.
>18Db
Internal Sync.
2:1 Interlace
0.45
15.734KHz (H) / 60Hz (V)
Composite: 1.0 Vp-p / 75 Ohm
12VDC
100mA
-10° ~ 60°C (14° ~ 140°F) Less Than 80% RH
3.7mm/F2.0
2.75” x 4.72” x 1.69” (70mm x 120mm x 43mm)
Application Note:
• Use a professional CCTV monitor only to achieve best resolution and performance.
• Camera may also be connected to other devices such as a DVR .
• Use copper braid RG59U coax for best video performance. Video may also be transmitted via
CAT5E cable with the use of video baluns .
• 12VDC Regulated power adapter 12V must be used otherwise the device will be damaged
and un-repairable.
3
LIMITED LIABILITY WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of any
rightful claim of infringement or the like, and when used in the manner
intended, will be free of defects in materials and workmanship for a
period of three (3) years, or as otherwise stated above, from the date of
purchase by the end user. This warranty is nontransferable and extends
only to the original buyer or end user customer of a VITEK Authorized
Reseller.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
VITEK Authorized Reseller.
28492 Constellation Road ValenCia, Ca 91355
WWW.ViteKCCtV.CoM
4
Loading...