Vitek VTD-MVP922-L35, VTD-MVP922-L35-B User Manual

Mighty Series True

Day & Night Dome

700 TVL Day & Night

Dome Cameras

VITEK

• 1/3” Sony High Density EXVIEW CCD

• 700 TVL High Resolution

• Sony Effio-E Digital Signal Processor

• 0.0003Lux (F1.2@50IRE)

• 2DNR - Two Dimensional Noise Reduction

• Motion Detection

• Privacy Mask

• Adaptive Tone Reproduction

• Secondary Video Output (Cable Included)

• OSD (On Screen Display) for Camera Function Setup

• Flush or Surface Mount

• Infinity Ball Mount for Any Viewing Angle

• UTP Interface and Heater / Blower Options Available

• ¾” Conduit Knockouts

• Indoor and Outdoor IP 686 Vandal Versions

• 35 IR LED’s with 90ft Range (Model L35)

• Optional Extreme Cold (-60°F) Temperature Kit Available

• Available in Ivory or Black

• Dual Voltage 12VDC & 24VAC

Cameras

BLACK

TABLE OF CONTENTS

BOX CONTENTS

INCLUDED ACCESSORIES

AVAILABLE MODELS/ACCESSORIES

MIGHTY DOME LAYOUT

INSTALLATION

JUNCTION BOX INSTALLATION

OPEN GIMBAL COVER

CONNECTIONS

LENS ADJUSTMENT

INFINITE AXIS GIMBAL ADJUSTMENT

OSD MENU FEATURES/SETUP

1. In the menu

2. MAIN menu

3. MAIN menu - 1

4. MAIN menu - 2

5. SHUTTER/AGC menu

6. SHUTTER/AGC > AUTO SETUP menu

7. SHUTTER/AGC > MANUAL SETUP menu

8. LENS menu

9. DAY/NIGHT menu

10. PICT ADJUST menu

11. WHITE BAL menu

12. ATR (Adaptive Tone Reproduction) menu

13. BACKLIGHT menu

14. NR menu

15. MOTION DET menu

16. PRIVACY menu

1

1

2

3

4

5

6

7

8

9

10

10

10

10

11

11

12

13

13

13

15

15

17

18

18

19

19

TABLE OF CONTENTS

17. LANGUAGE menu

VITEK

18. CAMERA ID menu

19. CAMERA RESET

20. EXIT

DIMENSIONS

HEATER/BLOWER SPECIFICATIONS

INDOOR MIGHTY DOME SPECIFICATIONS

VANDAL MIGHTY DOME SPECIFICATIONS

IR MIGHTY DOME SPECIFICATIONS

WARRANTY

20

20

21

21

22

23

24

25

26

29

BOX CONTENTS

1) Dome Camera

2) Accessories

3) VT-MD-2VOC (Secondary Video Output Cable)

4) Instruction Manual & Mounting Template

INCLUDED ACCESSORIES

Torx Wrench - (Vandal & IR Versions Only)

Type #: T20
Length: 63mm / Diameter: 4mm
Qty: 1

Phillips head Screws - (Vandal & IR Versions Only)

For attaching the dome cover to the flush housing.
Type #: Phillips head M4x10
Length: 10mm / Diameter: 4mm
Qty: 4

Self Tapping Screws

For attaching the surface mount housing or the the flush mount base to a
solid surface.
Type #: Phillips St4x30
Length: 30mm / Diameter: 4mm
Qty:4

Self Tapping Screws - (Indoor Version Only)

For attaching the dome cover to the flush housing.
Type #: Phillips St4x12
Length: 12mm / Diameter: 4mm
Qty: 4

Dowels

If necessary, use the to help secure the self tapping screws.
Length: 30mm / Diameter: 7mm
Qty: 4

Secondary Video Output Cable for Mighty Domes:

VT-MD-2VOC

For viewing video image during installation.
Qty: 1

Mounting Template

Surface Mount

109.0

70.0

Mounting Template

Qty: 1

1

BLACK

AVAILABLE MODELS / ACCESSORIES

INDOOR MIGHTY DOME CONFIGURATIONS:

VTD-MP2810DN: Indoor True Day and Night Color Dome Camera with 2.8-10mm
Varifocal Lens & 700TVL

VTD-MP922DN: Indoor True Day and Night Color Dome Camera with 9-22mm
Varifocal Lens & 700TVL

VTD-MP1850DN: Indoor True Day and Night Color Dome Camera with 18-50mm
Varifocal Lens & 700TVL

VANDAL RESISTANT MIGHTY DOME CONFIGURATIONS:

VTD-MVP2810DN: Vandal Resistant True Day and Night Color Dome Camera with

2.8-10mm Varifocal Lens & 700TVL

VTD-MVP922DN: Vandal Resistant True Day and Night Color Dome Camera with
9-22mm Varifocal Lens & 700TVL

VTD-MVP1850DN: Vandal Resistant True Day and Night Color Dome Camera with
18-50mm Varifocal Lens & 700TVL

IR MIGHTY DOME CONFIGURATIONS:

VTD-MVP2810/L35: Vandal Resistant Color Dome Camera with 2.8-10mm Varifocal
Lens, 700TVL & 35 IR LED’s

VTD-MVP922/L35: Vandal Resistant Color Dome Camera with 9-22mm Varifocal
Lens, 700TVL & 35 IR LED’s

VTD-MVP1850/L35: Vandal Resistant Color Dome Camera with 18-50mm Varifocal
Lens, 700TVL & 35 IR LED’s

Optional Mounts & Accessories:

1. Heater/Blower Option 24VAC: (Vandal Resistant Models)

2. UTP Option: Unshielded Twisted Pair Transceiver Built-In

3. VT-MD/FMP: Flush Mount Plate for installation in drop ceilings or can be used as cover plate when using 4S

Junction Box

4. VT-MD/PLMT: Mighty Dome Pole Mount Adapter - Requires VT-MD/WMT Wall Mount

5. VT-MD/CMT: Mighty Dome Ceiling/Pedestal Mount (Can be extended if necessary)

6. VT-MD/CNMT: Mighty Dome Corner Mount Adapter - Requires VT-MD/WMT Wall Mount

7. VT-MD/WMT: Mighty Dome Wall Mount (Available In Ivory or Black)

8. VT-MD-EMP: Extender Mounting Plate - Use as stand-off for cable management and extended viewing angle

1. 2. 3. 4. 5. 6. 7.

8.

2

MIGHTY DOME LAYOUT

1) Lens

2) Power Input Connector(12VDC /

24VAC)

3) Video Output Connector - BNC

4) Camera Holder and 2nd Video

output

5) Ball with the Camera Assembly

6) Safety Wire

7) Bubble

8) Dome Cover Ring

9) Flush Mount Base

10) Surface Mount Plate

11) Assembly Screws - Torx M4x9

(Vandalproof)

12) Assembly Screws - Phillips
ST4x12 (Indoor) / Phillips M4x10
(Vandalproof / IR)

13) Mounting Screws - Phillips ST4x30

3

BLACK

INSTALLATION

1) Dome Cover

1.1 Vandal Proof Domes - Use the provided Torx wrench to unscrew the vandal
proof screws and remove the dome cover.

1.2 Indoor Domes - Turn the dome cover to the left to remove the dome cover.

2) Flush Mount Installation:

Using four St4x30 screws, attach the flush mount base to a sturdy surface.
Optional flush mount decorator plate. Model: VT-MD-FMP

3) Surface Mount Installation:

Drill pilot holes at the mounting location using the provided mounting template.
Using four St4x30 screws, mount the surface mount housing to a sturdy
surface. Using four ST4x12 (Indoor) screws or M4x10 (Vandal-proof) screws,
attach the flush mount base to the surface mount housing.

4

JUNCTION BOX INSTALLATION

Mighty Domes can easily be flush or surface mounted to an electrical junction
box (4S J-Box) using the pre-drilled mounting holes on either the surface mount
housing or the the flush mount base.

5

BLACK

OPEN GIMBAL COVER

To adjust the zoom and the focus, the gimbal needs to be removed temporarily
from its base.

1) Remove the ball gimbal from its socket, and hold the base firmly with one hand.

2) Gently squeeze Point A and B and pull away from the base until the gimbal is

removed from the base.

3) Replace the Gimbal cover by aligning the cover to the base and pressing down
until it snaps back onto the base.

6

CONNECTIONS

• Power connection: 12VDC or 24VAC dual input.

• All Mighty Dome cameras come standard with a secondary video output. The
secondary video cable (VT-MD-2VOC) is included in the box.

VTM-LCD

7

BLACK

LENS ADJUSTMENT

1) Remove the Gimbal cover from the Gimbal base.

2) Loosen Zoom & Focus screws and make necessary adjustments as shown.

Field of view: Telephoto(T) to Wide(W)
Focus: Near(N) to infinity( )

3) OSD Joystick Control

4) Reattach the gimbal cover to the gimbal base.

8

1.) Remove the Gimbal Cover from the Gimbal Base

2.) Loosen Zoom & Focus screws and make necessary adjustments as shown.

Field of View: Telephoto (T) to Wide (W)
Focus: Near (N) to Infinity ( )

3.) OSD Joystick Control

8

4.) Reattach the gimbal cover to the gimbal base

3

OSD Joystick

Control

8

BLACK

INFINITE AXIS GIMBAL ADJUSTMENT
Rotation and “Friction Hold” Placement

The Gimbal mechanism yields maximum rotation and placement as shown below.

9

OSD Menu Features/Setup

Exits the setup menu. To save the changes, move cursor to 'SAVE ALL'
and press button before exiting the setup menu.

MAIN menu-1

MAIN menu-2

3 MAIN menu-1

SETUP menu

1 In the menu

Use , buttons to move the cursor and , buttons to change the settings.
Press button to select or enter. button stands for MENU or ENTER button.

2 MAIN menu

Follow the chart for submenu settings

MAIN menu-1 Default Descriptions

SHUTTER

/AGC

LENS AUTO

DAY/NIGHT AUTO

PICT ADJUST -

WHITE BAL ATW

ATR OFF

BACKLIGHT OFF

Sets the parameters related to the shutter mode and AGC for AUTO and

AUTO

MANUAL settings. See page 11 for ‘SHUTTER/AGC menu' details.

Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens
only. See page 13 ‘LENS menu' for details.

Sets DAY/NIGHT mode to AUTO, COLOR or B/W.

AUTO – Camera switches DAY from/to NIGHT automatically.
BURST, DELAY CNT, DAYNIGHT, NIGHTDAY can be set.

See page 13 for ‘DAY/NIGHT menu' details.

COLOR – Day/Night is disabled and forces to DAY mode only.
B/W – Day/Night is disabled and forces to NIGHT mode only.

Camera removes IR cut filter and switches to B/W.

Sets MIRROR, BRIGHTNESS, CONTRAST, SHARPNESS, HUE or GAIN.
See page 15 for ‘PICT ADJUST menu' details.

Sets ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.
See page 15 for ‘WHITE BAL menu' details.

Sets ON/OFF for enabling/disabling ATR (Adaptive Tone Reproduction)
compensation for the better dynamic range of the image.
See page 17 for ‘ATR menu' to adjust the dynamic ranges.

Selects BACKLIGHT mode out of OFF, HLC or BLC. Areas and gains for
HLC and BLC are factory preset and not user adjustable.

NEXT Moves to MAIN menu-2.

EXIT

SAVE ALL

Saves all parameters by pressing button.

10

BLACK

OSD Menu Features/Setup

See page 19, 'PRIVACY menu' for the parameter settings.

button before exiting the setup menu.

4 MAIN menu-2

MAIN menu-2 Default Descriptions

5 SHUTTER/AGC menu

NR -

MOTION DET OFF

PRIVACY OFF

LANGUAGE

ENGLISH

CAMERA ID OFF

CAMERA

RESET

BACK Returns to MAIN menu-1.

EXIT

SAVE ALL

This menu offers how to control/select SHUTTER, AUTO IRIS and AGC to get the best image for the
high luminance and the low luminance according to the scene.

For example, to reduce the wash out and extend the dynamic range for the highlight scene, it is
improved by SHUTTER+AUTO IRIS in the outdoor daylight. This mode may show color rolling or the
video level hunting problem in certain lighting condition such as fluores

Flickerless mode reduces the flickers by NTSC camera under 50Hz light o r PAL camera under
60Hz light. MAIN> SHUTTER/AGC> MANUAL> SHUTTER must be set to 1/100 (NTSC), 1/120 (PAL)
and MAIN> SHUTTER/AGC> AUTO> MODE to AUTO IRIS. Normal shutter speed with an auto iris
lens should be set to 1/60 (NTSC) and 1/50 (PAL) for the best sensitivity.

To enter SHUTTER/AGC menu, press button at MAIN menu-1>SHUTTER/AGC.

Sets the noise reduction parameters for NR MODE, Y LEVEL and
C LEVEL. See page 18 for ‘NR menu' details.

Sets ON/OFF for enabling/disabling MOTION DET.
See page 19, ‘MOTION DET menu' for the parameter settings.

Sets ON/OFF for enabling/disabling PRIVACY.

Selects the language out of 7 languages.

Sets ON/OFF for enabling/disabling of ID display.
Factory default ID is this version of the camera.
User programmed camera ID will be lost and restored with Factory default
ID after CAMERA RESET. See page 20, 'ID menu' for editing ID.

Restores FACTORY DEFAULT.
To save the restored parameters, move cursor to 'SAVE ALL' and press

Exits the setup menu.
To save the changes, move cursor to 'SAVE ALL' and press button.

Saves all settings by pressing button.

cent lights.

11

NESS

speed control + an auto iris lens.

HIGH LUMINANCE

LOW

LUMINANCE

OSD Menu Features/Setup

6 SHUTTER/AGC>AUTO SETUP menu

AUTO SETUP Default Descriptions

MODE

BRIGHT-

MODE AGC Sets AGC to compensate the video level when the scene is dim.

NOTICE : The setting AUTO IRIS at SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE will be
changed to SHUT+AUTO IRIS if MAIN menu-1>LENS is changed to MANUAL.

As a result, the lens iris can NOT be fully opened when MAIN menu-1>LENS>AUTO IRIS>

This can be recovered by setting SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE
to AUTO IRIS.

BRIGHT-

NESS

MODE is OPEN.

AUTO

x0.50

Selects the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when
MAIN>LENS>AUTO but it is fixed to SHUT if MAIN>LENS>MANUAL.

AUTO IRIS - Light level is controlled by an auto iris lens only.
For proper auto iris operation, the auto iris operation mode in MAIN>
LENS>AUTO>MODE must be set to AUTO.

The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC>
MANUAL> SHUTTER in this mode.
Set SHUTTER to 1/60 (NTSC) or 1/50 (PAL) for the best sensitivity
unless it is in Flickerless mode.

To set Flickerless mode: MAIN>SHUTTER/AGC>MANUAL>SHUTTER

IRIS

must be set to 1/100 (NTSC), 1/120 (PAL) and MAIN>SHUTTER/AGC>
AUTO>MODE to AUTO IRIS.

SHUT+AUTO IRIS- Light level is controlled by the combination of an
auto iris lens and shutter control to improve the highlight from wash­ out and extend the dynamic range. Shutter speed can vary between
1/60(1/50)~1/10,000sec.

This mode enhances the overall video quality of daylight but may show
a smeared image in bright spotlights. However, color rolling or video
level hunting may occur under a certain lighting condition such as
fluorescent lights.

Adjusts the brightness of the image by an auto iris lens or a shutter

032

Sets the brightness level which starts AGC from x0.25, x0.50, x0.75 and
x1.0 of full video level.
If set to x0.50, the camera will start AGC when the video level goes
down to below the 50% level.

12

BLACK

Lens is fully closed.

MANUAL

SETUP

SHUT
+AGC

OSD Menu Features/Setup

7 SHUTTER/AGC>MANUAL SETUP menu

MODE

SHUTTER

AGC 6.00

8 LENS menu

To enter LENS menu, press button at MAIN menu-1>LENS>AUTO.

AUTO IRIS Default Descriptions

TYPE DC

MODE AUTO

SPEED 080

9 DAY/NIGHT menu

To enter DAY/NIGHT menu, press button at MAIN menu-1>DAY/NIGHT

Default Descriptions

Compensates the video level by the manual shutter control and AGC.

Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000,

1/60

(1/50)

1/2000,1/4000 or 1/10000.
Manual shutter is only useful when luminance is unchanged.

Sets AGC gain in dB. Higher gain compensates for a brighter scene, but
noise increases.
Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44 8dB.

MUST BE SET TO DC ONLY.

This camera does NOT support video type auto iris lens.

AUTO – Lens iris is automatically controlled according to the scene’s
light level.

OPEN – Lens is fully opened regardless of the light level.
CLOSE –

Adjusts the iris control speed.
The lower the value, the faster the speed.
If the speed is too slow or fast, the iris control may be unstable.

13

If the scene is too dim or the lens iris was adjusted too low (near close), it may not return to DAY.

OSD Menu Features/Setup

IMPORTANT ACTIVITY!!!

DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final
installation.

Block the lens for a few seconds for NIGHT mode, then release and let it return to DAY mode.
If camera stays at NIGHT mode for more than 10sec, slightly increase ‘N→D THRES’ and repeat the fore­mentioned steps.

DAY/NIGHT Default Descriptions

BURST OFF

DELAY

CNT

DAY→NIGHT 005

NIGHT→

DAY.

BURST mode contains color burst signal when the camera switches to B/W.
ON mode maintains the same color signal in B/W so that the video signal
provides better compatibility with certain color equipment.
OFF mode removes the color burst signal B/W video and increase the total TV
lines.

DELAY CNT is the time in seconds before Day↔Night switches. DELAY can

005

avoid the unwanted/frivolous switching of short term lights such as light from
a passing car.

DAY→NIGHT mode sets a threshold level to determine when switch from
DAY to NIGHT. Lower (Higher) value makes the camera switched from Day to
Night at lower (higher) illumination.
If the camera stays in Color at night time, increase D AY→NIGHT threshold
value until it just switches to Night.

CAUTION If the value between DAY→NIGHT and NIGHT→DAY is

minimal, then camera may switch between DAY and NIGHT mode
repeatedly.

NIGHT→DAY mode sets a threshold level to determine when to switch from

NIGHT to DAY. Lower (Higher) value makes the camera switched from Night
to Day at lower (higher) illumination.
If the camera stays in B/W mode during day time, decrease NIGHT→DAY

3

threshold value until it switches to Day.

CAUTION If the value between DAY→NIGHT and NIGHT→DAY is

minimal, then camera may switch between DAY and NIGHT mode
repeatedly.

14

BLACK

OSD Menu Features/Setup

will decrease.

as well as line flicker at the edge of object in the picture.

10 PICT ADJUST menu

To enter PICT ADJUST menu, press button at MAIN menu-1>PICT ADJUST.

PICT ADJUST Default Descriptions

MIRROR OFF Picture will be flipped horizontally if it turns ON.

BRIGHTNESS 000

CONTRAST 120 Increases or decreases the contrast of the picture.

SHARPNESS 128

HUE 128 Adjusts hue for NTSC version only.

GAIN 128 Increases or decreases the color gain of the picture.

1 WHITE BAL menu

1

White balance can be set to ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.
ATW (Auto Tracking White balance) and PUSH (Full pull-in) are continuously monitoring/analyzing the
color temperature of the incoming light and correcting the white balance.

ATW limits the color temperature range at about 2,500˚K~8,500˚K to reduce the excessive
compensation for the big object which has a single color.
PUSH has no limits between about 1,800˚K~10,500˚K but it may over-compensate the white balance for
the big object which has a single color.

In cases where it goes under 2,500˚K such as halogen light, ATW may stop. If so, PUSH mode is
recommended.

USER1 and USER2 are a fixed white balance which is user -programmable by R-GAIN and B-GAIN and
useful only for the steady light.

ANTI CR (Anti Color Rolling) can reduce color rolling under the fluorescent light when the camera
operates in shutter control without an auto iris lens. (NTSC version only)

Increases or decreases the brightness of the picture.
This is different from that of DC iris lens because it simply increases or
decreases the digital gain of the video.
Do not increase this too much or the dynamic range for the highlight area

Increases or decreases the sharpness of the picture.
Too much sharpness can make the image too harsh and show more noise

15

OSD Menu Features/Setup

MANUAL white balance is a kind of fixed white balance which is user-programmable by B-GAIN.
(R-GAIN will be automatically adjusted in accordance with B-GAIN) and useful only for the steady light.

PUSH LOCK is a fixed white balance where the white balance is compensated only while the button
is pressed at MAIN>WHITE BAL>PUSH LOCK and finishes the white balance when button is
released.

To enter ATW (MANUAL) menu, press button at MAIN menu-1>WHITE BAL>ATW(MANUAL).

ATW Default Descriptions

SPEED 250

DELAY CNT 001

ATW FRAME X2.00

ENVIRON-

MENT

MANUAL WB Default Descriptions

LEVEL 064 Manual White Balance Adjustment value.

INDOOR

Sets the AWB compensating speed. Lower value makes AWB faster.

CAUTION Too fast an AWB may force color oscillation.

Adjusts the AWB compensation period to next update of AWB.
The smaller value will update AWB more frequently (faster).

Determines the ATW range with respect to the fundamental range.
A higher value than x1.00 extends the ATW range at lower and higher color
temperature.

Selects INDOOR or OUTDOOR.
Their ATW is optimized for the limited application and cannot cover.

INDOOR - Optimized for Indoor installation and compensates ATW for low
color temperature such as incandescent lights.
OUTDOOR - Optimized for outdoor sunlit applications and compensates
ATW for high color temperature such as daylight.

16

BLACK

OSD Menu Features/Setup

increase in the dark area.

12 ATR (Adaptive Tone Reproduction) menu

The ATR feature improves the dynamic range and the visibility of the image by providing the optimal
gradation compensation of the image in one field. This is achieved by two ways of image processing,
luminance compression and contrast enhancement, so that the tone can be enhanced at highlighted and
dark areas.

To enter ATR menu, press button at MAIN menu-1>ATR.

ATR Default Descriptions

LUMINANCE MID

CONTRAST MID

Compresses the highlighted area and enhances the dark area so that the
entire image can converge toward the medium level.
LOW will compensate minimally and HIGH will average out the image.
With setting HIGH, the image may look less contrastive and noise may

Adjusts the strength of the image contrast.
If set to too high, the dark area may lose detail and the high luminance
area may saturate.

17

OSD Menu Features/Setup

BLC OFF

13 BACKLIGHT menu
To enter BACKLIGHT menu, press button at MAIN menu-1>BACKLIGHT.

14 NR menu

To enter NR menu, press button at MAIN menu-2>NR.

NR MODE Y/C Selects OFF, Y, C or Y/C which noise reduction is performed with.

Y LEVEL 006

C LEVEL 004

HLC OFF

NR Default Descriptions

Indicates the noise reduction strength for the luminance signal.
Higher value performs stronger noise reduction and makes the image
less sharp. Due to the limitation of 2D NR, noise reduction may not be
effective enough.

Indicates the noise reduction strength for the chrominance signal.
Higher value performs stronger noise reduction and makes the image
less sharp. Due to the limitation of 2D NR, noise reduction may not be
effective enough.

BLC ON

HLC ON

18

BLACK

OSD Menu Features/Setup

MONITOR

AREA

15 MOTION DET menu

Up to 4 motion detection areas are available and each area is programm able in size and location.
The motion is displayed by means of blocks when MAIN menu-2>MOTION DET and MOTION
DET>BLOCK DISP are ON.

To enter MOTION DET menu, press button at MAIN menu-2>MOTION DET>ON.

MOTION DET Default Descriptions

DETECT SENSE

BLOCK DISP ON

AREA SEL 1/4

16 PRIVACY menu

Up to 8 privacy areas are available and each area is programmable in size and location.
The number of privacy areas is limited to four when MOTION DET>MONITOR AREA is ON.
The privacy areas are masked with the color selected by PRIVACY>COLOR.

To enter PRIVACY menu, press button at MAIN menu-2>PRIVACY>ON.

080 Adjusts the sensitivity for detecting motion. A higher value is more sensitive.

Enables or disables displaying blocks for the area where the motion is
detected.

OFF Displays four motion windows as programmed in sizes and positions.

Selects AREA1~AREA4 to be adjusted.

TOP (BOTTOM) - button moves up and button moves down the top
(bottom) border of the selected window at AREA SEL.

LEFT (RIGHT) - button moves left and button moves right the left
(right) border of the selected window at AREA SEL

19

COMMAND LINE

CAMERA ID input line

OSD Menu Features/Setup

PRIVACY Default Descriptions

Selects one of AREA1~AREA8 to be adjusted.

AREA SEL 1/8

COLOR 1 Sets one of 8 colors for the selected mask window at AREA SEL.

TRANSP 1.00

MOSAIC OFF

17 LANGUAGE menu
Seven languages, ENGLISH ,JAPANESE, DEUTCH, FRANCAIS, RUSSIAN, PORTUGUES and
ESPANOL, are available with this camera.

18 CAMERA ID menu

Up to 40 characters can be input for camera ID.

To enter CAMERA ID menu, press button at MAIN menu-2>CAMERA ID.

Use , , , buttons to move a block cursor in character table and press button to input the
selected character.

To move the character input position on CAMERA ID input line, move a cursor to ←→ on COMMAND
LINE and press button on ← or →.
To clear CAMERA ID input line, move a cursor to CLR on COMMAND LINE and press button.
To set the location of CAM TITLE to be displayed on the monitor, move a cursor to POS and press
button. Then, the menu will disappear and the CAMERA ID will be displayed on the monitor.

Move CAMERA ID by using , , , buttons and press button to fix.
Menu will appear again.
To finish CAM TITLE menu, press button on RET on command line.

TOP(BOTTOM) - button moves up and button moves down the top
(bottom) border of the selected window at AREA SEL.

LEFT(RIGHT) - button moves left and button moves right the left
(right) border of the selected window at AREA SEL

Transparency rate for the mask can be adjusted.

0.00 - Mask is fully transparent and not visible.

0.50 - Mask is 50% transparent.

0.75 - Mask is 25% transparent.

1.00 - Mask is not transparent.

Enables or disables the mosaic effect for the selected mask window at
AREA SEL

20

BLACK

OSD Menu Features/Setup

19 CAMERA RESET

Camera loads Factory defaults.
To save them, go to SAVE ALL and press button.

20 EXIT

Exits SETUP MENU and returns to the normal display

21

DIMENSIONS

Indoor Vandal

31

22

BLACK

HEATER / BLOWER SPECIFICATIONS

HEADER

Specifications

Power Supply

Power Consumption

Heater

Blower

Extreme Weather Heater - Optional

24 VAC

10W (Heater) / .7W (Blower)

On: at 41ºF / Off at 59ºF

Continuous 24 Hour Operation

On: -60ºF

23

INDOOR MIGHTY DOME SPECIFICATIONS

HEADER

Specifications

NTSC PAL

Image Device

Image Processor

Effective Pixels

Scan System

Scan Frequency

Synchronization

Horizontal Resolution

Sensitivity

S/N Ratio

Electronic Iris

White Balance

Motion Detection

Privacy Mask

OSD Language

Day & Night

Lens Options

Video Output

Operating Power

Operating Condition

Dimensions (H x Dia.)

Weight (Camera)

Weight (Carton)

1/3” Sony High Density EXVIEW CCD

Sony Effio-E Digital Signal Processor

976(H) x 494(V) 976(H) x 582(V)

2:1 Interlace

59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H)

Internal

700TVL

0.0003Lux (F1.2@50IRE)*

More than 50dB with AGC OFF at 50IRE

1/60 ~ 1/100,000sec 1/50 ~ 1/100,000sec

1,800 ~ 10,5000K Automatic Tracking

YES (24x16 BLOCK ALARM AREA)

8 mask

EN, FR, DE, ES, POR, SC, RUS, JP

True Day and Night by ICR

F1.2 2.8-10mm DC Auto Iris IR Corrected ICR / F1.8 9-22mm

DC Auto Iris IR Corrected ICR / F1.5 18-50mm DC Auto Iris Corrected ICR

VBS 1 Vpp +/- 10%, 75ohm

24VAC / 12VDC

-4F ~ 122F (-20C ~ +50C), 85% RH. Max. Non-condensing

4.45” x 5.71” (113mm x 145mm)

1lb / .46Kg

1.6lb / .72Kg

*Light Sensitivity may vary depending on lens specifications and capsule density and color

24

BLACK

VANDAL MIGHTY DOME SPECIFICATIONS

HEADER

Specifications

NTSC PAL

Image Device

Image Processor

Effective Pixels

Scan System

Scan Frequency

Synchronization

Horizontal Resolution

Sensitivity

S/N Ratio

Electronic Iris

White Balance

Motion Detection

Privacy Mask

OSD Language

Day & Night

IP Rating

Lens Options

1/3” Sony High Density EXVIEW CCD

Sony Effio-E Digital Signal Processor

976(H) x 494(V) 976(H) x 582(V)

2:1 Interlace

59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H)

Internal

700TVL

0.0003Lux (F1.2@50IRE)*

More than 50dB with AGC OFF at 50IRE

1/60 ~ 1/100,000sec 1/50 ~ 1/100,000sec

1,800 ~ 10,500K Automatic Tracking

YES (24x16 BLOCK ALARM AREA)

8 mask

EN, FR, DE, ES, POR, SC, RUS, JP

Infrared Cut-Filter Removable Built-In

IP686

F1.2 2.8-10mm DC Auto Iris IR Corrected ICR / F1.8 9-22mm

Video Output

Operating Power

Operating Condition

Dimensions (H x Dia.)

Weight (Camera)

Weight (Carton)

*Light Sensitivity may vary depending on lens specifications and capsule density and color

DC Auto Iris IR Corrected ICR / F1.5 18-50mm DC Auto Iris Corrected ICR

VBS 1 Vpp +/- 10%, 75ohm

24VAC / 12VDC

-4F ~ 122F (-20C ~ +50C), 85% RH. Max. Non-condensing

4.45” x 6.73” (110mm x 170mm)

2.3lb / 1043g

2.9lb / 1315g

25

IR MIGHTY DOME SPECIFICATIONS

Specifications

NTSC PAL

HEADER

Image Device

Image Processor

Effective Pixels

Scan System

Scan Frequency

Synchronization

Horizontal Resolution

Sensitivity

S/N Ratio

Electronic Iris

White Balance

IR LED’s

Motion Detection

Privacy Mask

OSD Language

Day & Night

IP Rating

1/3” Sony High Density EXVIEW CCD

Sony Effio-E Digital Signal Processor

976(H) x 494(V) 976(H) x 582(V)

2:1 Interlace

59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H)

Internal

700TVL

0.0003Lux (F1.2@50IRE)*

More than 50dB with AGC OFF at 50IRE

1/60 ~ 1/100,000sec 1/50 ~ 1/100,000sec

1,800 ~ 10,500K Automatic Tracking

35 IR LED’s with up to 90’ Range

YES (24x16 BLOCK ALARM AREA)

8 mask

EN, FR, DE, ES, POR, SC, RUS, JP

Infrared Cut-Filter Removable Built-In

IP686

Lens Options

Video Output

Operating Power

Operating Condition

Dimensions (H x Dia.)

Weight (Camera)

Weight (Carton)

*Light Sensitivity may vary depending on lens specifications and capsule density and color

F1.2 2.8-10mm DC Auto Iris IR Corrected ICR / F1.8 9-22mm

DC Auto Iris IR Corrected ICR / F1.5 18-50mm DC Auto Iris Corrected ICR

VBS 1 Vpp +/- 10%, 75ohm

24VAC / 12VDC

-4F ~ 122F (-20C ~ +50C), 85% RH. Max. Non-condensing

4.45” x 6.73” (110mm x 170mm)

2.3lb / 1043g

2.9lb / 1315g

26

BLACK

VTM-LCDP Series

15”, 17“, and 19” Professional LCD Monitors

• 15”, 17“, and 19” Professional LCD Display Panels

• Designed for continuous 24/7 operation

• VGA, Looping BNC Composite, and S-Video Video

Inputs. DVI & HDMI Inputs on 17“ & 19” Versions

• Resolution up to 1280 X 1024 (17” & 19”)

• Stereo Audio Input/Output

• VESA Standard Mounting

27

CHRONO Series

8, and 16 Channel Digital Video
Recorders

• Highly efficient H.264 compression

• Built-in Data Redundancy

• Real-time recording and real-time playback

• System Setup Wizard and User Friendly GUI

• Multi-Resolution recording

• 4 Spot Output (8 &16 Channel)

• Highly efficient and stable proprietary Database
Structure

• Identical GUI for DVR and client viewer

• Built-in Point-of-Sales support

• Web clients & CMS (Central Management Software)
Included

• iPhone App

28

H.264

BLACK

LIMITED LIABILITY WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of any
rightful claim of infringement or the like, and when used in the manner
intended, will be free of defects in materials and workmanship for a
period of three (3) years, or as otherwise stated above, from the date of
purchase by the end user. This warranty is non-transferable and extends
only to the original buyer or end user customer of a VITEK Authorized
Reseller.

The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the guar­antee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels. War­ranty support is available only if product is purchased through a VITEK
Authorized Reseller.

28492 CONSTELLATION ROAD VALENCIA, CA 91355

WWW.VITEKCCTV.COM