Vitek VTC-IR40-N User Manual
VITEK
ENVI Series
ENVI Series 1.3 & 2.0MP Vandal
Resistant Day/Night IR Bullet
Camera Series w/150’ Range
• 1/3” 1.3 & 2.0 Megapixel Progressive Scan CMOS image sensors
• Up to 30fps live view @ 1920x1080p (2.0 MegaPixel Models) / 1280x1024 (1.3
MegaPixel Models)
• 2.8-10mm Varifocal Auto Iris Lens
• Integrated 850nm Infrared LEDs with up to 150’ Range
• Dual Glass Compartments to Eliminate Glare
• 2.8-10mm Varifocal DC Auto Iris IR Lens
• Heavy Duty IP68 rated weather resistant aluminum construction
• Secondary Video Output & OSD Control Joystick are accessible inside a Gasket
sealed removable side panel
• Externally adjustable Focus & Zoom with clutch to eliminate over-tightening
• 3D-DNR Noise Reduction
• 16:9 (2.0 MegaPixel Models) / 4:3 (1.3 MegaPixel Models) Video format
• Secondary video output for installation & maintenance
• Auto True Day Night (TDN) without focus shift is achieved with dual filter switch
function
• H.264/MJPEG Dual Streaming
• Full duplex 2 way audio, Alarm IN/OUT
• Minimal Latency w/Max 16 User Connections
• Onvif Compliance
• SD memory card slot for Local recording
• 12VDC/24VAC & PoE (Power over Ethernet) Operation
Specifications & installation procedure subject to change without notice.
Visit www.vitekcctv.com for the most current information available.
ENVI Series: VTC-IR40-N
1
Table of Contents
1. Box Contents............................................................................................................................ 6
2. Included Accessories ................................................................................................................ 6
3. VTC-IR40-N Layout ................................................................................................................... 7
3.1. Front View ................................................................................................................... 7
3.2. Rear Side View ............................................................................................................. 7
4. VTC-IR40-N Installation ............................................................................................................ 8
4.1. Mounting The Camera .................................................................................................. 8
4.2. Connections ................................................................................................................. 8
4.3. Pan/Tilt Adjustment ...................................................................................................... 9
4.4. Setup Menu ............................................................................................................... 10
4.5. Removable Storage .................................................................................................... 11
5. Camera Software Installation .................................................................................................. 12
6. VTC-IR40-N Features .............................................................................................................. 15
7. IP Installer: Introduction ......................................................................................................... 15
8. Installing and Uninstalling ....................................................................................................... 15
8.1. Installing IP Installer .................................................................................................. 16
8.2. Uninstalling IP Installer ............................................................................................... 19
9. Using IP Installer .................................................................................................................... 21
9.1. Starting the Program .................................................................................................. 21
9.2. Search Product ........................................................................................................... 22
9.3. Automatic Network Setup ........................................................................................... 25
9.4. Using DHCP Server ..................................................................................................... 27
9.5. Using PPPoE .............................................................................................................. 28
9.6. Updating Firmware ..................................................................................................... 30
9.7. Filter Configuration ..................................................................................................... 32
9.8. Live View ................................................................................................................... 33
10. ENVI Admin Menu ................................................................................................................ 35
10.1. Entering Admin Menu ................................................................................................. 35
10.2. Admin Menu Structure ................................................................................................ 36
11. Quick Configuration .............................................................................................................. 36
11.1. Step 1: Changing Server Name.................................................................................... 36
11.2. Step 2: Time Setup ..................................................................................................... 36
11.3. Step 3: Network Setup ................................................................................................ 36
11.4. Step 4: IPCCTVDNS.COM ............................................................................................ 37
11.5. Step 5: Recording Configuration .................................................................................. 37
11.6. Finish......................................................................................................................... 37
ENVI Series: VTC-IR40-N
2
12. System Configuration Menu .................................................................................................. 37
12.1. Server Name Setup..................................................................................................... 37
12.2. Date & Time............................................................................................................... 38
12.3. Admin Password ......................................................................................................... 39
12.4. Access Control ............................................................................................................ 39
12.5. User Registration ........................................................................................................ 39
12.5.1. Add ................................................................................................................. 39
12.5.2. Edit ................................................................................................................. 41
12.5.3. Delete ............................................................................................................. 41
13. Network Configuration .......................................................................................................... 41
13.1. Static IP Configuration ................................................................................................ 42
13.2. DHCP Client Configuration ........................................................................................... 42
13.3. PPPoE Configuration ................................................................................................... 43
13.4. Network Ports ............................................................................................................ 43
13.5. Bandwidth Control Configuration ................................................................................. 44
13.6. View Network Status................................................................................................... 44
13.7. Network Status Notify ................................................................................................. 45
13.8. IP-CCTV DNS Setup .................................................................................................... 46
13.9. Port Forwarding & UPnP ............................................................................................. 47
13.10. R TP/RTSP Setup ......................................................................................................... 48
14. Device Configuration ............................................................................................................ 49
14.1. Privacy Zone .............................................................................................................. 49
14.2. Camera & Motion ....................................................................................................... 52
14.3. Camera Configuration ................................................................................................. 54
14.3.1. Rate Control Mode ........................................................................................... 55
14.3.2. Image Quality Setup ........................................................................................ 55
14.4. Camera Control (Select Models)................................................................................... 55
14.5. DI (Sensor Input) / DO (Alarm Output) ........................................................................ 79
15. Advanced Configuration ........................................................................................................ 81
15.1. Advanced Services ...................................................................................................... 82
15.1.1. E-mail Service Configuration ............................................................................. 83
15.1.2. FTP (Buffered) Service Configuration ................................................................. 86
15.1.3. FTP (Periodic) Service Configuration .................................................................. 88
16. Recording Configuration for Cameras with SD card ................................................................. 90
16.1. SD / MicroSD Card Configuration ................................................................................. 90
16.2. Recording Configuration with SD ca rd .......................................................................... 93
17. Utilities ................................................................................................................................ 95
17.1. System Log ................................................................................................................ 96
17.2. Save Configuration ..................................................................................................... 96
ENVI Series: VTC-IR40-N
3
17.3. Reboot ....................................................................................................................... 97
17.4. Factory Default ........................................................................................................... 97
17.5. System Update ........................................................................................................... 98
18. ENVI Series Viewer............................................................................................................. 101
18.1. Introduction ............................................................................................................. 101
18.2. Key Features ............................................................................................................ 101
18.3. System Requirement for PC....................................................................................... 101
19. Installing and Uninstalling ................................................................................................... 102
19.1. Installing ENVI Series Viewer .................................................................................... 102
19.1.1. Installing on Web Browser .............................................................................. 102
19.1.2. Manual Installation ......................................................................................... 104
19.2. Uninstalling ENVI Series Viewer ................................................................................. 105
19.2.1. Uninstalling with Program Menu ...................................................................... 105
19.2.2. Uninstalling on Control Panel .......................................................................... 106
20. Starting ENVI Series Viewer ................................................................................................ 107
20.1. Control Bar .............................................................................................................. 108
20.2. Channel Control Bar .................................................................................................. 109
20.3. OSD Channels Buttons .............................................................................................. 109
20.3.1. Saving as Image File ...................................................................................... 109
20.3.2. Saving as Video File ....................................................................................... 110
20.3.3. Manual Recording .......................................................................................... 110
20.3.4. Instant Playback ............................................................................................ 111
20.4. Extended Features .................................................................................................... 112
20.4.1. Pausing Live Video ......................................................................................... 112
20.4.2. FPS Control ................................................................................................... 112
20.4.3. Flip Control .................................................................................................... 113
21. EN-V-R: Introduction .......................................................................................................... 113
22. Requirements for Installation .............................................................................................. 114
22.1. EN-V-R Versions ....................................................................................................... 114
22.2. System Requirement for PC....................................................................................... 114
23. Installing EN-V-R ................................................................................................................ 115
24. Uninstalling EN-V-R ............................................................................................................ 118
24.1. Closing Active EN-V-R ............................................................................................... 118
24.2. Executing Uninstaller ................................................................................................ 119
25. Components of EN-V-R Program ......................................................................................... 120
25.1. EN-V-R Configurator ................................................................................................. 120
25.2. EN-V-R Service ......................................................................................................... 120
25.3. EN-V-R Controller ..................................................................................................... 120
25.4. EN-V-R System Tray Menu ........................................................................................ 120
26. Starting EN-V-R Configurator .............................................................................................. 121
ENVI Series: VTC-IR40-N
4
27. Quick Start Guide ............................................................................................................... 122
27.1. EN-V-R Configurator User Interface ........................................................................... 122
27.2. Searching for IP Devices ........................................................................................... 123
27.3. Registering IP Devices .............................................................................................. 125
27.4. Viewing Live Video ................................................................................................... 127
27.5. Recording Video ....................................................................................................... 129
28. ENVI Smart Player .............................................................................................................. 133
28.1. Introduction ............................................................................................................. 133
28.2. Key Features ............................................................................................................ 133
28.3. System Requirement for PC....................................................................................... 134
29. Installing and Uninstalling ................................................................................................... 134
29.1. Installing Smart Player .............................................................................................. 134
29.1.1. Manual Installation ......................................................................................... 135
29.2. Uninstalling Smart Player .......................................................................................... 136
29.2.1. Uninstalling on Program Menu ........................................................................ 136
30. Configuring & Viewing Player .............................................................................................. 146
30.1. Main Window View ................................................................................................... 147
30.2. Connecting to NVR Player ......................................................................................... 148
30.3. Creating a Group ...................................................................................................... 148
31. Searching Video ................................................................................................................. 150
31.1. Searching Video ....................................................................................................... 150
31.2. Daily Search ............................................................................................................. 150
31.2.1. Search Mode .................................................................................................. 151
31.2.2. GO to Time Position ....................................................................................... 151
31.3. Condition Search Mode ............................................................................................. 151
31.3.1. Advanced Search Mode .................................................................................. 152
32. Video Playback Controls ...................................................................................................... 153
33. Extra Features ................................................................................................................... 154
33.1. Window Control ........................................................................................................ 154
33.2. Recording Period ...................................................................................................... 154
33.3. Backup .................................................................................................................... 155
33.4. Snapshot ................................................................................................................. 156
33.5. Print ........................................................................................................................ 157
33.6. Ratio Display ............................................................................................................ 157
34. EN-V-R Configuration ......................................................................................................... 158
34.1. System, Network Configuration ................................................................................. 158
34.1.1. Configuring System name ............................................................................... 159
34.1.2. System, Network Configurat i on - Ad min password ........................................... 160
34.1.3. System, Network Configurat i on - Access Control .............................................. 160
34.1.4. System, Network Configurat i on - HTTP Port..................................................... 161
ENVI Series: VTC-IR40-N
5
34.1.5. System, Network Configurat i on - IP-CCTV DNS ................................................ 161
35. IP-CCTV DNS Registration .................................................................................................. 162
36. IP-Device Registration ........................................................................................................ 167
36.1. IP-Device Registration (Manual) ................................................................................ 168
36.2. IP-Device Registration (Automatic) ............................................................................ 170
IP-Device Modification ................................................................................................. 172
36.3. IP-Device Deletion .................................................................................................... 174
36.4. IP-Device Homepage ................................................................................................ 174
36.5. Camera Management ................................................................................................ 174
36.5.1. Configure Camera Name and Information ........................................................ 175
36.5.2. Camera Resolution, Quality ............................................................................. 176
36.5.3. Configure Camera Recording Condition ........................................................... 177
36.5.4. Alarm, Event Configuration ............................................................................. 180
36.6. User Management .................................................................................................... 181
36.6.1. User Registration ........................................................................................... 182
36.6.2. User Modification ........................................................................................... 182
36.6.3. User Deletion ................................................................................................. 183
36.7. Disk Setup ............................................................................................................... 183
36.7.1. Disk Setup ..................................................................................................... 183
36.7.2. Disk Quota Modification and Deletion .............................................................. 183
36.7.3. Disk Mode Change ......................................................................................... 184
36.8. Utilities .................................................................................................................... 186
36.8.1. Email account Configuration ........................................................................... 186
36.8.2. About Program .............................................................................................. 187
37. Using EN-V-R Controller ...................................................................................................... 188
38. Connecting to EN-V-R ......................................................................................................... 189
38.1. PC with EN-V-R installed ........................................................................................... 189
38.2. PC without EN-V-R.................................................................................................... 190
ENVI Series: VTC-IR40-N
6
1. Box Contents
1) VTC-IRE40-N Long range Weatherproof IR Bullet camera
2) Mounting Accessories
3) VT-MD-2VOC (Secondary Video Output Cable)
4) ENVI Series CD & Mounting Template
2. Included Accessories
3mm Hex L-wrench
Qty: 1
Wall mounting screws
Qty: 4
Anchors
If necessary, use the anchor to help secure the self tapping screws.
Qty: 4
Sunshield with Attachment thumb screw
Qty: 1
VT-MD-2VOC (Secondary Video Output Cable)
For viewing video image during installation.
Qty: 1
RJ45 Coupler
Qty: 1
Mounting Template
Qty: 1
ENVI Series CD
Qty: 1
ENVI Series: VTC-IR40-N
7
3. VTC-IR40-N Layout
3.1. Front View
3.2. Rear Side View
ENVI Series: VTC-IR40-N
8
4. VTC-IR40-NInstallation
• Make sure the power is not applied before the installation.
4.1. Mounting The Camera
1. Drill 4 holes into the wall or ceiling using the supplied tem p late
2. Insert the anchors into the drilled holes
3. Match (foot mount holes) to the drilled holes
4. Affix the mounting bracket by using supplied screws
4.2. Connections
1. Power
Depending on the type of installations, apply power to the camera by one of the three
options below.
a) Via Ethernet – Use only with POE switch (100 Meters max distance)
b) 12VDC - Use with 12VDC 1A ** SEE IMPORTANT NOTES BELOW **
c) 24VAC- Use with 24VAC for longer distances.
**
It is required that the polarity-matched connection is made for 12VDC supply ,
otherwise IR LEDs will not operate at night. **
Primary and secondary grounds are completely isolated to avoid possible ground-loop
problems.
ENVI Series: VTC-IR40-N
9
2. Ethernet Connection
Insert one end of the Ethernet cable into the network jack of your camera, and insert the other
end into the data port (switch, router, etc)
3. Alarm Connections
This camera support Alarm IN/OUT, Green = alarm IN, Blue = alarm OUT. (For more
information, refer to Section 14.5DI (Sensor Input) / DO (Alarm Output) on page 79)
4. Audio In/Out
This camera supports RCA Audio IN/OUT, (Audio IN White, Audio OUT Red)
4.3. Pan/Tilt Adjustment
1. Tilt Adjustment
Pan is limited to +/- 90°.
2. Tilt Adjustment
Tilt is limited to 0° (2°) min ~ 90° max.
ENVI Series: VTC-IR40-N
10
3. Camera Rotation
Inclination limited to +/-90° max.
4.4. Setup Menu
1. Accessing the Setup Menu & Controls
The Setup menu can be accessed and controlled in two ways:
a) Via the OSD control joy stick located on the side of the camera
ENVI Series: VTC-IR40-N
11
b) Via the Web-Admin, Device Configuration> Camera & Motion> Camera Control.
NOTICE: If the OSD menu is crushed and blurred, is due to small image size. Please have the
secondaryimage size at 640x352
NOTE: For further information on OSD menu, refer to Section14.4Camera Con tr ol (Select
Models) on page 55.
4.5. Removable Storage
For recording directly on the camera you wil l need to install a SD card, this will allow you to
play video directly from the camera. (** Please use only class 10 SD cards).
a) With the power disconnected insert the SD memory card as shown below (the SD card
willneed to be formatted.(refer to Section 16.1SD / MicroSD Card Configurationon page
90for instructions on Formatting)
ENVI Series: VTC-IR40-N
12
5. Camera Software Installation
1. Run IP Installer Software from the CD program on a computer that is on the same network
as the IP camera.
2. StartIP Installer, by double clicking the icon “IP Installer”
3. After the program has started, the main window of IP Installer program will appear on the
screen as shown below.
4. Search for the installed camera on the network by clicking the searc h product icon, the
camera should appear as the image below. The default IP address is 10.20.30.40
5. To assign an automatic IP address to this camera within the network, click the “Automatic IP
Setup” icon
6. Verify the Automatic IP address provided, enter the default password root and t hen click Set
as shown below.
ENVI Series: VTC-IR40-N
13
7. After the camera was configured by the program automatically, you will be able to get access
by
a) Right click over the camera information, “
Go Product Homepage
”
b) Click over the icon “
Connect Product Homepage
”
8. From the Home Page, you can “
Live View”
or administrate
“Admin”
the camera.
ENVI Series: VTC-IR40-N
14
On Live View you will be able to see live video from your camera.
NOTE: For more inform ation, refer to
Section 10. ENVI Admin Menu on page 35
.
ENVI Series: VTC-IR40-N
15
6. VTC-IR40-N Features
1.3 & 2.0 MegaPixel Vandal Resistant Day/Night IR Bullet Cameras with 150’ Range
• 1/3” 1.3 & 2.0 Megapixel Progress ive Scan CMOS image sensors
• Up to 30fps live view @ 1920x1080p (2.0 MegaPixel Models) / 1280x1024 (1.3 MegaPixel
Models)
• 2.8-10mm Varifocal Auto Iris Lens
• Integrated 850nm Infrared LEDs with up to 150’ Range
• Dual Glass Compartments to Eliminate Glare
• 2.8-10mm Varifocal DC Auto Iris IR Lens
• Heavy Duty IP68 ra ted weather resistant aluminum construction
• Secondary Video Output & OSD Control Joystic k ar e accessible inside a Gasket sealed
removable side panel
• Externally adjustable Focus & Zoom with clutch to eliminate over-tightening
• 3D-DNR Noise Reduction
• 16:9 (2.0 MegaPixel Models) / 4:3 (1.3 MegaPixel Models) Video format
• Secondary video out put for installation & maintenance
• Auto True Day Night (TDN) without focus shift is achieved with dual filter switch function
• H.264/MJPEG Dual Streaming
• Full duplex 2 way audio, Alarm IN/OUT
• Minimal Latency w/Max 16 User Connections
• Onvif PSIA Compliance
• SD memory card slot for Local rec ording
• 12VDC/24VAC & PoE (Power over Ethernet) Operation
7. IP Installer: Introduction
IP Installer is a proprietary utility program for VitekIP products. It enables users of Vitek products
to search their network for any Vitek network camera, video server, or network video recorder no
matter what IP address it has. By using IP Installer, users will be able to facilitate network setup
process for Vitek products deployment.
Runs on Microsoft Windows operating system (XP, Vista, 7, 8)
Search for Network Cameras, Video Servers, and Network Video Recorders
Capable of firmware updating
Support automatic and manual IP setup
8. Installing and Uninstalling
** It’s recommended to install this program as an administrator **
ENVI Series: VTC-IR40-N
16
8.1. Installing IP Installer
If the program is started from the CD supplied with Vitek products, insert the CD in to CD/DVD tray
and check the installation file. If it is download or copied from the Internet or any other media,
locate the file from the PC’s hard drive. You will see the icon as shown with the file name IP
Installer_Setup_x.x.x.exe. The act ual file na me in your case may vary as the version changes.
Double click the icon to star installation.
You may be prompted to cont inue running the installation program.
Click Yes button, then the following window will be shown on the screen.
ENVI Series: VTC-IR40-N
17
To continue the installat ion, click Next. The following window will be displayed for location to
install.
The default location for installation is C:\Program Files\IP Installer. It is recommended to install
in this folder, if you want to change it to a different loc ation, click the Browse button to choose
location. Now click the Install button. You will see the progress of theinstall as shown below.
ENVI Series: VTC-IR40-N
18
When the files are done copying, the foll owing window will be shown. Click the Finish button to
complete the installation.
ENVI Series: VTC-IR40-N
19
8.2. Uninstalling IP Installer
If you want to remove the IP Installer program from your PC, click Start > All Programs > IP
Installer > Uninstall.
You may be prompt to continue running theuni nstall program.
Click onthe Yes button, then the following window will be shown on the screen.
Click on the Next button and you will see the following window.
ENVI Series: VTC-IR40-N
20
Click on the Uninstall button to start removing the IP Installer program from your compute r.
The following window will be displayed.
Click on the Finish button to close the window
ENVI Series: VTC-IR40-N
21
9. Using IP Installer
9.1. Starting the Program
Once IP Installer program has been installed on your computer, a shortcut icon
should be created on the desktop of your computer.You can star t IP Installerby
double clicking the icon.
Or you can also st art the program by cl icking Start > All Programs > IP Installer > IP
Installeras shown below.
After the program has started, the main window of IP Installer program will appear on the
screen as shown below. There are no network devices shown,as it is the first time running the
program and nothing has been registered.
Search Product
Scan the network and shows the list of all the Vitek products that IP
Installer program found.
Clear Product List Clear the Vitek products list created by searching the network.
ENVI Series: VTC-IR40-N
22
Automatic IP Setup Configure the network setting of selected IP device in Automatic mode.
Manual IP Setup Configure the network setting of selected IP device in Manual mode.
Connect Product
Homepage
Connect to the server homepage of the selected IP device.
Update Firmware Update the firmware of the selected IP device.
Filter Configuration Define the range of MAC and IP addresses to search.
9.2. Search Product
Make sure that your Vitek products are powered and connected to the network, and then
click the Search Product button. A status window will pop up to show the progress of
the search. Wait until it reaches 100%, or you may press the Cancel button to stop the
search at any given timeand proceed with the results made until that moment.
After searching is completed 100%, the IP Installer program w ill disp lay the IP devices found.
If you want to clear the list of the IP Devices from the window, click Clear Product List
button from the Main Toolbar.
ENVI Series: VTC-IR40-N
23
Manual Network Setup
Configuring the network parameters of the devices in the list can be started either by
highlighting and right clickingmouse button or by clicking Manual IP Setupbutton on the
main Toolbar.
When one IP device is selected, the following screen will appear
MAC Address MAC address of the selected device is shown.
Server Name Input desired name of camera i.e. Lunch Room
HTTP Port Input port number to access IP devices homepage via web. Default port is 80
IP Type Select the type of address (Static / DHCP / PPPoE) Use STATIC for manual IP setup
ENVI Series: VTC-IR40-N
24
Network
General network parameters are required in this part. Please contact your network
administrator for detail.(IP Addr ess , Netmask, Default Gateway, DNS1, DNS2)
Authentication
(Admin Password)
Password for the IP d evice.
(Default password for Vitek products is “root” unless already changed)
Save Configuration
Option
Select whether the configured contents is to be saved in the Camera memory or not.
• Save Configuration: Changed values will be saved in the Camera memory of the
device, which means the changes are permanent.
• Not Saving: Changed values will not be sa ved in the Camera memory, which
means if the IP device is turned off the changes are lost and the previous setting
will be applied back.
Click Set button to app ly the changed values to IP device. If you don’t want it, click Cancel button.
When two or more IP devices are selected
You can select two or more IP devices at the same time by clicking one after another while CTRL
key is pressed. The result is shown as bel ow.
To configure the network parameters of those devices, click the right mouse button or click
Manual IP Setup icon on the main Toolbarwith multiple IP devices selected as shown abo ve.
Then the following window will show up.
You can modify the value of each changeable field by clicking it. The following shows an example
of entering a new value to a field.
ENVI Series: VTC-IR40-N
25
Model Model Numbers of the IP devices that you selected.
MAC Address MAC address of the selected device is shown.
Server Name Name of the selected IP device.
IP Type
How to assign IP address to the device (Select
Static
here for Manual IP
Setup)
IP address, Netmask,
Gateway, DNS1, DNS2
General network parameters are required in this part. Please contact your
network administrator for detail.
HTTP Port HTTP port number of the IP device for web access to homepage.
Password Password for the IP device.(Default password for Vitek products is “root”)
If you click Apply to all button after changing just a field of one IP device, the remaining IP
devices will have the same value for that parameter. In this case, each device’s Server name and
IP Address field will have +1 incremented value added to the original value. For example, if the
first IP device has been given the server name of NetCam and Apply to all button is pressed, it
will be automatically changed to NetCam1 and the next IP device will have NetCam2 and so on.
The same applies to the IP address field.
For Password field, the entered information doesn’t increment but will use the same data .
In using Apply to all, you can choose which fiel d is affected. Put check marks only on t he field
you want to use this automatic action as below.
Click Save & Close button to save the changed value s in the camera memory of all the IP devices
and close the Network setup window.
9.3. Automatic Network Setup
Configuring the network parameters of the devices in the list can be started either by
clicking right mouse button or by clicking Automatic IP Setupbutton on the main
Toolbar. Before starting the setup, you first need to choose the one to be configured. In
this setup mode, IP Installer program checks your local network and assigns available IP addresses
to the IP devices. You have a choice of using those automatically assigned IP addresses, or you
can just enter other IP addresses as you desire.
ENVI Series: VTC-IR40-N
26
Server Name Name of the selected IP device.
HTTP Port HTTP port number of the IP device for web access to homepage.
IP Type How to assign IP address to the device (Select Static here for M anual IP Setup)
Network
General network parameters are required in this part. Please contact your network
administrator for detail. (IP Address, Netmask, Default Gateway, DNS1, DNS2)
Authentication
(Admin Password)
Password for the IP device. (Default password for Vitek products is “root”)
Save Configuration
Option
Select whether the configured contents is to be saved in the Camera memory or not.
• Save Configuration: Changed values will be saved in the Camera memory of the
device, which means the changes are permanent.
• Not Saving: Changed values will not be sa ved in the Camera memory, which
means if the IP device is turned off the changes are lost and the previous setting
will be applied back.
Click Set button to apply the changed va lues to IP device. If you don’t want it, click Cancel button
to restore the previous values.
ENVI Series: VTC-IR40-N
27
9.4. Using DHCP Server
If your network has a DHCP server running for assigning IP addresses, you may choose to let it
assign IP addresses to the IP devices on the list. To do that, first open the Network Setup window
either by Manual IP Setup or Automatic IP Setup procedure. Choose DHCP in “IP Type ”
selection, then IP Address, Netmask, Default Gateway field in Network setup area on the
window will be disabled to input as shown below.
Note: If your network has more than one IP address Zone at the same time, the
confirmation window will be displayed as below. You need to choose the one you
are going to use for your IP devices.
ENVI Series: VTC-IR40-N
28
For setting up other fi elds on the setup window, refer toSection0Manual Network Setupon
page 23. After filling the fields with appropriate values, click Set button to apply the changed
values to IP device. If you don’t want it, click Cancel button to restore the previous values.
9.5. Using PPPoE
If your network environment is based on P PPoE connection, you’ll need to choose PPPoE on IP
Type selection. First open the Network Setup window either by Manual IP Setup or Automatic
IP Setup procedure. Choose PPPoE in IP Type selection, and then all the fields in Network
setup area on the window will be disabled. The network settings such as IP Address, Netmask,
Default Gateway and DNS are no longer available to enter. You only need to enter the Server
Name, HTTP Port number, and login authentication for your PPPo E connection.
ENVI Series: VTC-IR40-N
29
MAC Address MAC address of the selected device is shown.
Server Name Name of the selected IP device.
HTTP Port HTTP port number of the IP device for web access to homepage.
IP Type How to assign IP address to the device (Select PPPoE in this mode)
PPPoE
User Authentication for PPPoE Connection.
• PPPoE User: Enter User ID.
• PPPoE Password: Enter Password for the User ID.
• PPPoE Password Confirm: Enter the same Password again.
Authentication
(Admin Password)
Password for the IP device.
(Default password for Vitek products is “root” unless already changed)
Save Configuration
Option
Select whether the configured contents is to be saved in the Camera memory or not.
• Save Configuration: Changed values will be saved in the Camera memory of the
device, which means the changes are permanent.
• Not Saving: Changed values will not be sa ved in the Camera memory, which
means if the IP device is turned off the changes are lost and the previous setting
will be applied back.
Note: After setting up the network for the IP devices, make sure the IP devices are
accessible on the network from your computer. It can be done by runni ng Live
View function of the homepage of the IP device’s built-in server. Refer to
Section
9.8
Live View
on page 33
for more information.
Loading...