Vitek VTC-IR403-212NP, VTC-IR403-550NP Quick Start Manual

VTC-IR403-212NP

VTC-IR403-550NP

Virtuoso Series 3.15MP WDR

IP Cameras with 40 IR LEDs

QUICK START GUIDE

VITEK

VITEK

FEATURES:

• 1/2.8” Sony® 3.23 MegaPixel RGB Bayer Array CMOS

• Up to 30fps live view @ 2048 x 1536 (3.15 MegaPixel)

• MegaPixel IR Corrected 2.8-12mm Motorized Varifocal Lens with 1 click
focus for easy Configuration or MegaPixel IR Corrected 5-50mm Varifocal
Auto Iris Lens with External Adjustments for Focus and Zoom

• 40 Dynamic Infrared LEDs at 850nm enable viewing in total darkness up to
150 feet

• Dual Glass Compartments to Eliminate IR Reflection

• XD-DNR (2D-DNR + 3D-DNR) Noise Reduction

• True Day/Night by ICR - Dual Filter Switch

• Triple Streaming (H.264/MJPEG) offering Extensive Integration Possibilities

• Real-time Lens Distortion Correction (LDC) for an optically correct picture

• Compliance with the latest Onvif Profile S

• On-board network security with IP address filtering

• Advanced OSD Features including Image Stabilization & Corridor Mode

• MicroSD memory card slot for Local recording supporting up to 128GB
MicroSDXC cards

• 3-Axis mount with Simple One Turn Positioning Lock for Ease of Installation

• IP-68 Rated Water Resistance

• 12VDC, 24VAC and PoE (Power over Ethernet) Operation

PLEASE NOTE:

Complete user guide available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Manuals/Virtuoso-IP_Operation-Manual.pdf

Safety Precaution

To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.

Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.

2 3

Composition

Camera

Plastic Anchor:

6 x 30mm (3pcs)

Mounting Screw:
4 x 40mm (3pcs)

Assembly Screw:

4 x 15mm (4pcs)

Torque Wrench:

3mm (1pc)

Dimensions

3.15”

3.53”

3.31”

Easy
Bracket

Mounting Template

Quich Start

Guide

Installation CD

Cable Signal
Sticker

Coupler for
RJ45 Cable (1pc)

Wiring Connector
(1pc)

3.94”

4.37”

3.39”

4.35”

10.11”

3

Part Names

SUNSHIELD BOLT

SUNSHIELD

DUAL WINDOW

FRONT CASE

REAR CASE

BRACKET

Cover Open

Micro
SD Card Slot

Reset Button

POWER CABLE

EASY
BRACKET

CAUTION

• Extreme care should be taken NOT to scratch the window in front of lens.

• Care should be taken that the cable is NOT damaged, kinked, or exposed in
a hazardous area.

• Do not point the camera lens directly at the sun or a spot light.

4 5

Installation Instructions

1. Place the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)

2. Place the easy bracket on pre-drilled position and attach using mounting
screws(4x30mm). Skip this step when an easy bracket is not installed.

3. Route the power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.

4. Attach the camera bracket using assembly screws (4x14mm).

5. Set the camera’s viewing angle.

6. Install the sunshield on to the camera unit and tighten the sunshield-bolt.

Plastic Anchor

: 6x30mm

Mounting Screw

: 4x30mm

Assembly Screw

Torque Wrench

: 4x14mm

2

4

1

3

REAR VIEW

Cable exit

5

Installation Instructions

Pan & Tilt adjustments

• Unlock the screw on the camera bracket using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

1) Pan limit:
Pan is limited to +/- 90°.

2) Tilt limit:

Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.

90° 90°

90°

80°

• on the wall• on the ceiling

3) Inclination limit

(Horizontal image alignment):
Inclination limited to +/-90° max.

±90°

Torque
wrench

■ Adjustment of viewing angle
with one-touch 3-Axis bracket

Lock/Unlock
Screw

Zoom & Focus adjustments (VTC-IR403-550NP Only)

Use the torque wrench supplied.

• Turn the Focus gear to “N”(Near) or “∞”(Far)
until the sharpest focus is made.

• To widen the viewing angle, turn the Zoom to
“W”(Wide) and to obtain a closer view, turn it
to “T”(Tele)

6 7