VTC-C680
VTC-C750
VTC-C680/DN
VTC-C750/DN
1/3” Color Camera Series
VITEK
• 1/3" Super HAD CCD With 550 TVL (VTC-C750 / VTC-
C750DN) & 480 TVL (VTC-C680 / VTC-C680DN)
• Minimum Illumination 0.02 Lux (F1.2) (VTC-C680DN / VTC-
C750DN) & 0.2 Lux (F1.2) (VTC-C680 / VTC-C750)
• Accepts DC Servo Type Auto Iris Lenses
• 2000-8000 Degree K Automatic White Balance Tracking
• Max 1/100,000 Sec. Electronic Shutter
• Better Than 48dB S/N Ratio (VTC-C680 / VTC-C750) &
50dB (VTC-C680DN / VTC-C750DN)
• 12VDC / 24VAC Dual Voltage Operation
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
1. Unit contains uninsulated dangerous
voltage within the enclosure that may
be of sufficient magnitude to
constitute a risk of electric shock to
persons
2. Only use DC Power Supply
3. Read & Keep these instructions.
4. Heed to all warnings and follow all
instructions carefully.
5. Do not use near water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. install in accordance with
the instructions.
8. Do not install near any heat source
such as radiators, heat resisters,
stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has to blades with
one wider the other. A grounding type
plug has to blades and a third
grounding plug. The wide blade or
the third prong are provided for
safety. if the provided plug dose not
fit into your into your outlet, consult
an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being
walked on a pinched particularly at
plugs, convenience receptacle, and
the point where they exit from the
apparatus.
11. Only use attachment/accessories
specified by VITEK.
12. Use only with cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the Unit,
13. Unplug this unit during lightning
storms or when unused for long
periods of time.
14. Refer all servicing to qualified service
personnel, Servicing is required
when the unit has been damaged in
any way, such as power-supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
unit, the unit has been exposed to
rain or moisture, does not operate
normally or has been dropped.
15. Do not attempt to service this
product yourself as opening or
removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service
personal.
CAUTION - To reduce the risk of electric
shock, do not perform any servicing
other than contained in these operating
instructions unless you are qualified to
do so.
2
CONTENTS
Safety Instructions & Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Introduction / Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Camera Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Rear Camera Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
External Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9
Power Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SAFETY INSTRUCTIONS & NOTES
• Please read these safety and operating instructions before putting the camera into
operation.
• Keep the operating instructions in a safe place for later use.
• The Standard Box Camera is designed for indoor use only and it must not be installed
where exposed to rain and moisture.
• The unit may only be opened by authorized personnel.
• Do not operate the cameras beyond their specified temperature, humidity or power
ratings.
• Pay attention when laying the connection cable and observe that the cable is not
subject to heavy loads, kinks, or damage and no moisture can get in.
• Power MUST be removed during installation.
• Do not attempt to disassemble the camera board from the camera.
• The warranty becomes void if repairs are undertaken by unauthorized persons.
• Contact the supplier if any functional problems arise.
CLEANING
• Do not use strong or abrasive detergents when cleaning this product.
• Use a dry cloth to clean the camera surface. In case the dirt is hard to remove, use a
mild detergent and wipe gently.
3
INTRODUCTION
VTC-C680 (VTC-C680DN for D&N) and VTC-C750 CCD Color Camera (VTCC750DN for D&N) are high performance standard box type color cameras that adopt
the most advanced 410,000 pixel 1/3” CCD. They are designed to have a conventional
camera appearance to act as a crime deterrent as well as remain unobtrusive when
installed. Its versatile design supports CS mount lens options allowing for various angles
according to the targeted installation environment. Their innovative LPF (Low Pass
Filter) and DSP technologies help represent natural colors. They are designed for indoor
use or outdoor use when installed in a weatherproof enclosure such as the
VITEK VT-EH10.
By utilizing a SONY CCD as well as a SONY HQ1 DSP, this camera provides
exceptionally sharp image quality up to 550TV Lines (for VTC-C750 & VTC-C750DN).
Through its backlight compensation function, it is able to give brighter and sharper
images of an object or objects darkened by background lighting or sunlight. Their highly
sensitive Super-HAD CCD also provides an auto white balance function, ensuring
accurate representation of colors under any lighting environment.
Either 24VAC or 12VDC (Non-Polarity) may be used with the use of a power adapter.
FEATURES:
• 1/3" Sony DSP Super-HAD Interline Transfer CCD
• Resolution of 480 Horizontal Lines (VTC-C680 / C680DN) / 550 Horizontal Lines
(VTC-C750 / C750DN)
• 10x Sensitivity enhancement with automatic optical filter (VTC-C680DN / C750DN)
• Switches to B/W, enabling IR sensitivity in night mode (VTC-C680DN / C750DN)
• Enhanced sharpness compensation
• Very low noise and superior picture quality
• Sensitivity of 0.02Lux (B&W) (VTC-C680DN / C750DN) & 0.2Lux (Color) (VTC-
C680 / C750)
• Supports DC (and Video) auto iris lens (VTC-C680 / C680DN)
• Automatic and Manual Removable IR Cut Filter (VTC-C680DN / C750DN)
• Digital signal processing (DSP)
• Automatic Shutter Control (AES)
• Automatic White Balance (ATW)
• Dual Voltage: 12VDC/24VAC
4
PACKAGE CONTENTS
Auto-iris lens Lens Connector
PIN 4 PIN 2
PIN 3 PIN 1
1 x 1/3” Digital Color Camera
1 x Lens Connector Plug (VTC-C680 / C680DN Only)
1 x CCD dust protection cap
1 x Instruction Manual
CAMERA LAYOUT
1) Back Focus Adjustment
3) CCD Dust Protection Cap
5) Back Focus Adjustment Screw
2) C-Mount Adapter Ring
4) Lens Connector for Auto-Iris Lenses
6) Threaded Camera Mount
Pin Video Drive DC Drive
1
2
3
4
V+(10V out)
No Connect
Iris Signal
GND
Damp(-)
Damp(+)
Drive(+)
GND
5
REAR CAMERA LAYOUT
VTC-C680 VTC-C680/DN
VTC-C750 VTC-C750/DN
1) Function Switches (SW1~4/8)
3) Lens Select Switch
5) Power Indicator LED
2) Iris Level Control
4) Video Output Connector
6) Power Input Terminal (Terminal Block)
6
EXTERNAL CONTROLS
Potentiometer for Iris level control:
Used to set the video level by adjusting the iris of the connected DC drive (or Video)
auto iris lens. This excellent lens control characteristic makes it very precise, very stable,
and very easy to adjust the video level.
Increase
Brightness.
(Clockwise)
VTC-C680 & VTC-C750 Dip Switches:
Function ON OFF
ALC / ESC
1
Back Light Control (BLC)
2
Flickerless
3
Auto Gain Control (AGC)
4
VTC-C680DN & VTC-C750DN Dip Switches:
ESC
On
On
Turbo
* Factory Defaults Shown in Bold.
Function ON OFF
ALC / ESC
1
Back Light Control (BLC)
2
Flickerless
3
Auto Gain Control (AGC)
4
ESC
On
On
Turbo
Decrease
Brightness.
(Counter Clockwise)
ALC
Off
Off
Normal
ALC
Off
Off
Normal
5
6
7
8
Sharpness
Day / Night
IR Mode
N/A
ON
ON
On
* Factory Defaults Shown in Bold.
7
Off
Off
Off
EXTERNAL CONTROLS
SW 1. ALC / ESC (Default: ALC)
Used to select iris control mode. When set to ESC, camera operates in electronic
shutter control (ESC) mode and can be installed with a manual or fixed iris lens. ESC
mode is the most economic solution but may have some following disadvantages
comparative to ALC mode with auto iris lens:
• More smear and less clear image when shooting the very bright object.
• Color rolling or video level hunting may occur under the florescent light when the
camera operates in ESC and INT modes (NTSC version only).
When set to ALC, camera operates in auto iris lens control mode and should be
installed with an auto iris lens. Auto iris lens is used for best quality video.
SW 2. BLC (Backlight compensation) ON/OFF (Default: OFF)
If the subject you wish to view is too dim because of a bright background, set the BLC
switch to ON to compensate for the bright background. With BLC on, the background
brightness may saturate in some cases. This function may not operate properly if the
object is too small compared to the area of the background. This function can be used
with the linear shutter (EE or ESC) and be OFF with auto iris lens (Al lens or ALC
mode).
SW 3. Flickerless ON/OFF (Default: ON)
Flickerless mode is useful in areas where AC main is 50Hz and TV system is NTSC
such like Japan or AC is 60Hz and TV system is PAL to reduce the flicker under the
florescent light. Where FL is set to ON, the low light sensitivity is down about 30%.
SW 4. AGC Turbo ON/ OFF (Default: OFF)
AGC is Automatic Gain Control
SW 5. Sharpness ON/OFF (Default: ON)
SW 6. Day-Night (ICR) ON/OFF (Default: ON)
DAY-NIGHT ON/OFF SW enables or disables the day-night mode. If set to ON, daynight mode is enabled and camera determines to enter / exit NIGHT mode from / to
DAY mode automatically according to the scene illumination. When the scene
illumination is getting darker than a half video level, camera changes its mode to NIGHT
and removes its optical filter to get a higher video level and switches to B/W mode.
In NIGHT mode, camera provides the real time B/W video and can accept the IR light.
When the illumination is getting brighter, camera returns to DAY mode and returns its
optical filter and switches to Color mode.
If set to OFF, camera operates just like a normal camera and does not perform NIGHT
mode.
8
EXTERNAL CONTROLS
A
SW 7 IR mode ON/OFF ((Default: OFF)
Used to reduce a possibility from Day to Night or reverse under a certain scene
illumination. This mode was derived from a IR Cut filter mechanism which is switched
from day to night or night to day based on scene illumination. A typical IR cut filter type
D/N camera could be switched from color to B/W or reverse under specific scene
illumination values, but sometimes iterations occur when switching from/to (Night <-->
Day) under specific external IR light source. VITEK IR mode can give a little margin of
the IR iteration at specific condition by increasing the threshold value (Night to Day)
adjustment.
When IR mode is enabled, it reduces iteration of the filter switch (repeated IN andOUT) during varying lighting conditions. In IR mode, the Night to Day threshold will be
around 6.0Lux and around 4.0Lux when off. The Lux is affected by scene illumination,
but has a limit to reduce IR iteration under stronger external IR light.
SW 8. N/A (Reserved for future usage)
POWER SUPPLY CONNECTIONS
VTC-C680 / C750 Cameras are dual voltage and can work with either 12VDC or
24VAC power. A polarity-matched connection for 12VDC supply is NOT required.
Primary and secondary grounds are completely isolated to reduce the possibility of
ground-loop problems. An operating voltage range of 9.5V-30V for DC and 12-28.8V
for AC provides extra installation flexibility.
Installation Notes:
Before applying voltage, first connect the power supply to the camera, then connect the
power supply to an AC source. Connecting a live power supply directly to the camera
could trigger an improper reset from power jitter and cause damage from surge voltage
when there is no load.
CLASS 2
C 24V
DC 12V
+
-
~
~
9
VTC-C680 / C750 SPECIFICATIONS
4.17”
2.56”
2.17”
VTC-C680 VTC-C750
Image Device
Image Processor
Effective Pixels
Scan System
Scan freq.
Sync. System
Resolution
Sensitivity
S/N Ratio
Electronic Iris
White Balance
External Dip Switches
External Potentiometer
Video Output
Lens mount
Operating Power
Power Consumption
1/3" Sony New Structure Super HAD Color CCD
DSP (Digital Signal Processor)
768(H) x 494(V)
2:1 Interlace
60Hz(V), 15.75Khz(H)
Internal
480TVL 550TVL
0.2Lux (F1.2@40IRE)
50dB (AGC OFF at 50IRE) 48dB (AGC OFF at 50IRE)
1/60 ~ 1/100,000sec
2000~8000ºK Automatic tracking
ALC/ ESC, BLC, Flickerless, AGC
Video Level Adjustment (Iris)
Composite: 1.0 Vp-p / 75 Ohm
CS Mount
12VDC/24VAC (Dual Voltage)
3 Watts (max)
Operation Temperature
Dimensions (W x H x L)
2.56" x 2.17" x 4.17" (65mm x 55mm x 106mm)
Weight
-10ºC~+50ºC, 85% RH. Max
5.29 Oz. (150g)
10
VTC-C680DN / C750DN SPECIFICATIONS
VTC-C680DN VTC-C750DN
Image Device
Image Processor
Effective Pixels
Scan System
Scan freq.
Sync. System
Resolution
Sensitivity
S/N Ratio
Electronic Iris
White Balance
External Dip Switches
External Potentiometer
Video Output
Lens mount
Operating Power
Power Consumption
1/3" Sony New Structure Super HAD Color CCD
DSP (Digital Signal Processor)
768(H) x 494(V)
2:1 Interlace
60Hz(V), 15.75Khz(H)
Internal
480TVL 550TVL
0.02Lux (F1.2@40IRE)
50dB (AGC OFF at 50IRE) 48dB (AGC OFF at 50IRE)
1/60 ~ 1/100,000sec
2000~8000ºK Automatic tracking
ALC/ ESC, BLC, Flickerless, AGC, Sharpness, Day/Night, IR Mode
Video Level Adjustment (Iris)
Composite: 1.0 Vp-p / 75 Ohm
CS Mount
12VDC/24VAC (Dual Voltage)
3 Watts (max)
Operation Temperature
Dimensions (W x H x L)
2.56" x 2.17" x 4.17" (65mm x 55mm x 106mm)
Weight
-10ºC~+50ºC, 85% RH. Max
5.29 Oz. (150g)
11
LIMITED LIABILITY WARRANTY
Your new Camera is guaranteed to be free from defects in materials
and workmanship for a period of two years from the date of
purchase.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental
damage, caused by excessive voltage or lightning.
The product must not have been tampered with in any way then the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact VITEK or your local distributor if servicing should become
necessary.
28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM | 888-VITEK-70
12
Loading...