Vitek VTC-BHOCRAZE User Manual

VITEK

VITEK

FEATURES:

• 1/3” Progressive Scan CMOS Sensor

• 2.1 MegaPixel With full 1080p/720p HD-SDI (SMPTE292M) / EX-SDI
Output

• Up to 30fps live view@ 1920x1080 (1080p)

• MegaPixel IR Corrected 3-9mm (VTC-BHOCRAZE39) / 9-22mm (VTC­BHOCRAZE922) Motorized Auto Focus Zoom Lens

• True Day/Night with Dual Filter Switch

• 16:9 Video format

• On-board Intelligence (OBI Technology) delivers Auto-Focus-Zoom by
tracking motion, then optically zooming into that area of the frame

• Fully programmable advanced WDR

• 40 850nm IR LEDs with up to 150’ IR range

• Integrated Cooling Fan

• Advanced OSD Functions: Motion Activated Pointing Zoom, Defog, Smart
Dynamic IR, BLC/HLC, Motion Deblur, Pixel Defect Compensation, Title Set,
Mirror, Flip, Lens Refresh, Lens Initialize, Home Position, DSS, LED ON/OFF
control

• 100% Pure Digital Transmission of video data

• Extended Range Beyond 1000’ with RG59U 95% Copper Braid Coax

• Heavy Duty IP68 rated water/vandal resistant aluminum construction

• 12VDC / 24VAC Dual Voltage Operation

VTC-BHOCRAZE

2.1MP HD-SDI / EX-SDI

Vandal Resistant AFZ/WDR

IR Bullet Camera

2 3

Safety Precaution

CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.

Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).

The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.

3

Safety Precaution

NOTICE

• The image used in this instruction manual are processed to help
comprehension and may differ from actual video of the camera.

• Avoid installing in areas where shock or vibration may occur.

• Pay attention to safety when running the connection cables and

make sure that the cables are not subject to heavy loads, kinks,
moisture or damage.

• Never open the device (no user serviceable parts inside). The
warranty becomes void if repairs are undertaken by
unauthorized persons.

• Maintenance and repair have to be carried out only by authorized
service centers.

• Use only a mild detergent to clean the housing.

• The camera should never be operated beyond the technical

specifications. This can lead to damaging the device and void
the warranty.

• The camera should never be operated in water.

4 5

Contents

p. 2~3

Safety Precaution

p. 4

Contents

p. 5~6

Features

p. 6

Package Includes

p. 7

Dimensions / Part Names

p. 8~10

Installation Instructions

p. 11~28

Operating Instructions

p. 29

Specifications

p. 30

On Cue VT-HDOCE Series

p. 31

Limited Product Warranty

5

Features

Key Features

• Full HD, 2.1 Mega Pixel, EX-SDI CAMERA, 1920x1080(30p/25p)

• Extended long reach HD Solution

• True WDR(Wide Dynamic Range)

• Improved Noise reduction with enhanced 3D-NR

• VTC-BHOCRAZE39: f=3~9mm, F1.2~F2.1 Day & Night Motorized Auto
Focus and Zoom lens (Optical 3x Auto focus zoom / Digital 32x zoom)

• VTC-BHOCRAZE922: f=9~22mm, F1.6~F2.3 Day & Night Motorized
Auto Focus and Zoom lens (Optical 2.4x Auto focus zoom / Digital 32x zoom)

• Dual ICR Switch

• Focusing Status Indicator on Screen

- ★(Blue) Focusing in process

- ★(White) Focusing Completed

• Various Zooming Technologies

- Smart Motion Zoom an Automatic zoom in/out when motion is detected

- Pointing Zoom which enables the zooming of any area within the FOV

- Preset Zoom, up to 4 presets

• Home Position setting

• Motion Detection, Privacy Mask, Defog, Sens-up(x32), BLC/HLC,
D-Zoom, H/V/HV Flip, Motion Deblur, Pixel Defect Compensation,
Lens Refresh, Lens Initialize

• ID / TITLE / ZOOM RATIO DISPLAY

• Enhanced Sensitivity by DSS technology

• EX-SDI or HD-SDI switchable

• Top performance at low light sensitivity (Sens-up On)

• OSD menu & Video sub-out for easy installation & maintenance.

• Circuit protection against faulty connection in power polarity

• Isolated power supply against ground loop problem

• Remote control via RS-485 (Pelco-D/P)

• Firmware update via RS-485

• Built-in 40 LEDs

• LED ON/OFF control

• Dual Window, One-touch 3-Axis locking bracket, Easy Installation Pad

• Built-in cooling Fan & Heating function

• 100% Pure Digital Transmission of video data

• Extended Range Beyond 1000’ with RG59U 95% Copper Braid Coax

• Heavy Duty IP68 rated water/vandal resistant aluminum construction

• 12VDC / 24VAC Dual Voltage Operation

6 7

Features

Package Includes

Mounting Template

General Operation

Instruction

Camera

General Description

• With ICR mechanism,

- Enhances its sensitivity about 10x at night time

- Can accept infrared light

• With 24VAC/12VDC dual power design,

- Offers the flexibility of installation

- Ensures the reliability

This camera realizes the natural and crisp image as you see the scene in front of
you by adopting Auto Focus Full HD(1920x1080p) camera module.

Torque Wrench:

3mm (1pc)

Video Sub-out
Cable (1pc)

Assembly Screw:

4 x 14mm (4pcs)

Mounting Screw:
4 x 30mm (4pcs)

Plastic Anchor:

6 x 30mm (4pcs)

Easy
Bracket

Cable Signal

Sticker

Wiring Connector:

(1pc)

7

Part Names

Dimensions

(unit : inches)

LOCK/UNLOCK
SCREW

4.35

3.53

4.37

3.94

3.31

3.39

3.15

10.11

DUAL WINDOW

SUNSHIELD BOLT

SUNSHIELD

FRONT CASE

OSD Setup

CONTROL COVER

BRACKET

EASY
BRACKET

REAR CASE

POWER & VIDEO CABLE

8 9

Installation Instructions

Mounting Screw

: 4x30mm

Plastic Anchor

: 6x30mm

1

2

Torque Wrench

REAR VIEW

3

Cable exit

4

Assembly Screw

: 4x14mm

1. Place the mounting template at the installation position and drill the ceiling or
wall if needed. (*The easy bracket can not be installed on the ceiling)

2. Place the easy bracket on pre-drilled position and attach using mounting
screws(4x30mm). Skip this step when an easy bracket is not installed.

3. Route the power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.

4. Attach the camera bracket using the assembly screws (4x14mm).
Set the camera’s viewing angle.

5. Attach the sunshield to the camera unit and tighten the sunshield-bolt.

9

Installation Instructions

• Unlock the screw on the camera bracket through using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

Pan & Tilt adjustments

1) Pan limit:
Pan is limited to +/- 90°.

3) Inclination limit
(Horizontal image alignment): Inclination limited to +/-90° max.

2) Tilt limit:

Tilt is limited to 0°(2°) min ~ 90° max.
for wall (ceiling) installation respectively
with reference to the wall (ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.

■ Adjustment of viewing angle
with one-touch 3-Axis bracket

Torque
wrench

Lock/Unlock
Screw

90° 90°

80°

90°

±90°

• on the wall

• on the ceiling

10 11

Installation Instructions

Power Supply Connections

l Make sure the power is removed before installation.
l Camera can work with either 24VAC or 12VDC, dual voltage power .
l Primary and secondary grounds are completely isolated to avoid possible

ground-loop problems

※ Attach the Signal Assignment Sticker
in a visible spot for wiring reference.

VIDEO (BNC)

AC24V/GND (Black wire)

AC24V/DC12V (Red wire)

RTX-/RS485 (Gray wire)

RTX+/RS485 (White wire)

In case that HD-SDI/EX-SDI Inputs are not supported by your monitor, please
use HD-SDI/EX-SDI Converter to connect HD-SDI/EX-SDI cable with Monitor

11

Operating Instructions

l Setup menu can be accessed and controlled by OSD control joy stick on the

side of camera unit.

l Five commands are available with the joy stick.
l The design of OSD could be different according to the Model.

Using OSD controller

Video Sub-out
Connector

OSD Control

Joy Stick

SUB-OUT

Description of the joystick operation

1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec

2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.

3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left
or right.

4) ‘☟’denotes a long press down for about 2 seconds.

Description of the ZOOM & FOCUS* adjustment

1) ▲ : Zoom In

2) ▼ : Zoom Out

3) ◄ : Focus Near

4) ► : Focus Far

(*) Works only when OSD Menu is inactive.

Video format
Switch

Cover Open

12 13

Operating Instructions

Set the video format according to system,
EX-SDI or HD-SDI

VT-HD/EXD1 VT-HD/EXD1

VT-HD/EXD1

VT-HD/EXD1 VT-HD/EXD1

max 400 ft. via RG59u

max 400 ft.via

RG59u

1000 ft. + via

RG59u

HD-SDI

HD-SDI HD-SDI

HD-SDI

HD-SDI

HD-SDI

HD-SDI

EX-SDI

EX-SDI

EX-SDI

max 400 ft.via.

max 400 ft.via

RG59u

1000 ft. + via RG59u

RG59u

1000 ft. + via RG59u

Full-HD Camera

Full-HD Camera

Full-HD Camera

Full-HD Camera

Full-HD Camera

DVR (HD-SDI)

DVR (HD-SDI)

DVR (HD-SDI)

DVR (HD-SDI)

DVR (EX-SDI)

max 400 ft.via

RG59u

max 400 ft.via

RG59u

max 400 ft.via

RG59u

13

Operating Instructions

Direct Control menu

OSD menu Startup

MAIN

DEFAULT

DESCRIPTION

ZOOM/FOCUS

Sets FOCUS and ZOOM relative fuctions.

-

EXPOSURE

Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and
MOTION DEBLUR.

-

SCENE
ENHANCE

NORMAL

SCENE ENHANCE provides several ways to enhance the video
in various environments with settings of NORMAL, WDR,
D-WDR, BLC and HLC.

Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA

PICT ADJUST

Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET,
DISPLAY, DEFOG, POINTING ZOOM

SPECIAL

Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE and
FACTORY DEFAULT

SYSTEM

Sets 3DNR level. LOW, MID, HIGH

Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and COLOR D/N.
Set to EXT mode for cameras with IR-LED’s and set to AUTO mode
for non IR-LED camera types.

DAY/NIGHT

EXT

or

AUTO

3D-NR MID

l Press ‘●’(OSD menu Joy stick key) down for about 2 seconds to access the

setup menu mode.

l

Lens Initializing is strongly recommended at the first stage of the setup menu control.

ZOOM/FOCUS > LENS INIT > Press the joystick ‘☟’straight down for about
2 seconds.

MENU V5.xx

1. ZOOM/FOCUS

2. EXPOSURE

3. SCENE ENHANCE

4. 3D-NR

5. DAY/NIGHT

6. PICT ADJUST

7. SPECIAL

8. SYSTEM

9. EXIT

NORMAL
MID
EXT

SAVE&EXIT

14 15

Operating Instructions

SAVE & EXIT – Exits the menu after saving the parameters.

EXIT

ZOOM / FOCUS

FOCUS MODE
D-ZOOM
HOME POSITION
LENS REFRESH
LENS INIT.
RETURN

ZOOM PUSH
OFF
OFF
OFF
ON

☟

RET

• ZOOM PUSH: Focusing is activated only when zoom in/out is working.

• AUTO: Focusing is always working.

• MANUAL: Focusing can only be adjusted by ▲,▼ of OSD control joystick

or the remote control via RS-485.

• O-ZOOM RATIO: Sets the Optical ZOOM positon as Home Position.

(x1.0~x3.0 / x1.0~x2.4)

• DURATION: When ZOOM IN/OUT control is completed, camera will return to

the pre-defined Zoom position after the Duration time.
If SMART MOTION / PRESET ZOOM are running, duration for Home position
starts after finishing SMART MOTION / PRESET ZOOM.

1. ZOOM/FOCUS

: ZOOM PUSH, AUTO and MANUAL modes are available for focusing.

1-1. FOCUS MODE

(default: ZOOM PUSH)

: D-ZOOM (Digital zoom) is available up to 32x. D-ZOOM starts working when
the optical zoom reaches its maximum tele-position. Zoom ratio is displayed
on the bottom right corner of the monitor if SPECIAL>DISPLAY>ZOOM RATIO
is set to ON.

1-2. D-ZOOM

(default: OFF)

: Camera can be configured to return to pre-defined Zoom position automatically
after a certain period of time with no activity.
Home Position is recovered after the camera is re-initializing or Powered ON/OFF.

1-3. HOME POSITION

(default: OFF)

15

Operating Instructions

HOME POSITION

O-ZOOM RATIO
DURATION
RETURN

OZ X2.0
5sec
RET

2. EXPOSURE

: Set EXPOSURE MODE to AUTO, IRIS Priority, SHUT. Priority, MANUAL
and Flickerless. SHUT. Priority, MANUAL and Flickerless modes disable
SENS-UP and MOTION BLUR functions.

2-1. MODE

(default: AUTO)

: LENS REFRESH can be set to 1~10days and performs a scheduled LENS
Initialization automatically. Every initialization occurs when the time reaches
the scheduled time after setup or power up. When LENS REFRESH initiates
LENS Initialization, a notification LENS INITIALIZING appears on the top
left corner on the monitor.

1-4. LENS REFRESH

(default: OFF)

: Lens initialization is necessary during the installation or the regular operation
to align the position data with the mechanical positions whose lens elements
may move and deviate from its calibrated position by shock or vibration, for
example, during transportation.

LENS INIT starts the lens initialization when pressing the joystick lever straight
down for about 2 seconds.
LENS INIT checks the positions for zoom and focus at both end positions and
saves them for reference.
Lens initialization is automatically executed upon power up.

1-5. LENS INIT

(default: ON ‘☟’)

• It is necessary to execute LENS INIT in the following situations;

1) At the final step of installation.

2) When out of focus due to shock or vibration.

CAUTION

16 17

Operating Instructions

• AUTO: Optimizes the video level by controlling the iris and the shutter speed

automatically.

• IRIS Priority: Select to fix IRIS at a certain apperture and the video level is

controlled by an automatic shutter control. Lower IRIS LEVEL will close the iris
more and increase the field of depth in the daytime but significantly decrease
the low light performance. Too low of IRIS LEVEL will result in foggy
video by diffusion from the lens iris.

• SHUT. Priority: Select to fix SHUTTER speed at a certain speed and the video
level is controlled by an automatic iris control.
This mode is useful when color rolling occurs under fluorescent lighting.
This mode is not recommended for outdoor or daytime.

• MANUAL: Iris and Shutter can be set to fixed.

• Flickerless : Reduces flicker in video when US(60Hz)/EU(50Hz) mode is

used in 50Hz/60Hz fluorescent lighting respectively.

• AUTO: SENS-UP is enabled or disabled automatically by the scene brightness.
Higher SENS-UP can get brighter video but the slower frame rate will cause
motion blur and more white pixels. If set to AUTO, maximum integration limit
for SENS-UP can be set to x2, x4, X8, x16, X32 in SENS-UP menu.

• OFF: Disables SENS-UP.

: A brighter video can be obtained by increasing the exposure time at night
with SENS-UP. SENS-UP is the maximum integration of frames by DSS (Digital
Slow Shutter) in low light.

2-4. SENS-UP

(default: OFF)

: AGC amplifies the video gain for brighter video but will cause noise and white
pixel accordingly. AGC level less than 10 disables AUTO in DAY/NIGHT.

2-5. AGC

(default: 10)

EXPOSURE

MODE

BRIGHTNESS DAY

BRIGHTNESS NIGHT

SENS-UP

AGC

MOTION DEBLUR

RETURN

AUTO

OFF

ON

RET

|:::::::|::::::| 10
|::::::|:::::::| 8

|:::::::|::::::| 10

: Adjusts the brightness of day time video (0~20).

2-2. BRIGHTNESS

DAY (default:10)

: Adjusts the brightness of night time video (0~20).

2-3. BRIGHTNESS

NIGHT(default:10)

17

Operating Instructions

3D-NR is a very sophisticated and powerful time-based noise reduction technology
by monitoring the noise for several video frames and defining and eliminating them
consecutively at low light. Higher setting reduces more noise but results in losing the
sharpness and tail effects or motion blur may occur.

3-4. BLC

3-5. HLC

4. 3D-NR

: Cuts out the bright area with a black mask and excludes it from compensation.
Lower HLC LEVEL cuts out video from lower light levels (more sensitive).

: Improves the visibility for dark objects caused by bright back light.
Outside area of BLC window can over saturate.
BLC has a target window for compensation and its size and position can be set
by H-POS, V-POS, H-SIZE and V-SIZE.

3-2. WDR

3-3. D-WDR

: Improves the visibility for bright areas and dark areas by double capture of
image with LONG and SHORT exposures. WDR level can be selected
from LOW, MID and HIGH. Care should be taken to select this mode because
video may lose its quality in some environments by over compensation.

※CVBS video signal:Connecting 2nd video to CVBS port disables WDR function
temporarily. It should be considered when installer adjusts the video with
installation monitor via CVBS video signal.

: Improves the visibility by compensating the video gain for the dark area.
Noise can increase in the dark area accordingly.

3-1. NORMAL

(default)

: ON enables MOTION DEBLUR to reduce motion blur in certain indoor
environments. Noise or color rolling can increase.

2-6. MOTION DEBLUR

(default: ON)

3. SCENE ENHANCE

: Optimized for normal indoor and outdoor in good lighting conditions.

18 19

Operating Instructions

: Used when DAY or NIGHT is determined by light level through the lens and
DAY from/to NIGHT is switched automatically by the scene brightness.
D↔N THRESHOLD, D↔N DELY and SMART (DYNAMIC) IR can be set in the
menu. When EXPOSURE>AGC is less than 10, DAY/NIGHT AUTO is disabled
and forcibly switches to ___(DAY) to avoid malfunction. EXT, B/W (NIGHT)
and COLOR (DAY) is independent on AGC level. When EXTERNAL IR LED
is used with NON IR LED model, please set to IR LED MODE ON.

: DAY or NIGHT is determined by the built-in light photo sensor.
Camera with IR LED must be set to EXT.

DAY/NIGHT is used to control the setting during day-time and night-time operation.
Select the mode according to the lighting conditions and the camera type.
SMART (DYNAMIC) IR can be set to reduce the saturation by strong IR illumination
at night in any menu. Setting SMART (DYNAMIC) IR in any menu is identically
applied to other menu. Zero(0) turns off SMART (DYNAMIC) IR and High setting
decreases the saturation but the corners will be darker accordingly. IR LED Control
(AUTO/OFF) is available with IR LED model only. If IR LED is set to OFF, IR LED
will be turned OFF but DAY or NIGHT is still determined by the built-in light
photo sensor.

• D↔N THRESHOLD (0~20):
Sets the threshold level switching from/to DAY(color) or NIGHT(B/W).
Setting at a low level makes the camera enter NIGHT at a lower light level.
High level makes the camera exit NIGHT at a higher light level.

• D↔N GAP (0~15):
Sets the gap level switching from/to DAY(color) or NIGHT(B/W).

5-1. EXT

5-2. AUTO

5. DAY / NIGHT

DAY/NIGHT AUTO

D<->N THRESHOLD
D<->N GAP
D<->N DELAY
SMART IR
RETURN

5s

RET

|:::::::|::::::| 10
|:::::::|::::::| 10

|:::::::|::::::| 10

19

Operating Instructions

: DAY/NIGHT is disabled and outputs color video.

: Removes IR cut filter and switches to B/W regardless of light level.

• D↔N DELAY (0~60s):
Sets the delay time when the camera switches from/to DAY(color) or NIGHT(B/W).

5-3. B/W(NIGHT)

5-4. COLOR(DAY)

5-5. COLOR D/N

PICT ADJUST

WHITE BAL

SHARPNESS

COLOR GAIN

GAMMA DAY

SHADING

RETURN

ATW

0.50

AUTO

RET

6. PICT ADJUST

|:::::::|::::::| 10

|:::::::|::::::| 10

: Color D/N mode, optimized for night conditions. It is available to recognize
colors of car, people and moving objects even at night. Parameters can be
controllable & programmable according to the circumstances. Application is for
bright circumstances at night such as downtown, civic area, streets, mall, etc.

Conventional COLOR mode in NIGHT COLOR D/N mode in NIGHT

20 21

Operating Instructions

• ATW: White balance is continuously working along with the color temperature

changes in the range of 2,000K~8,500K.

• ATWext: White balance is continuously working along with the color temperature
changes in the range of 1,800K~11,000K.

• ONE PUSH: White balance works only while ● is pressed.

• MANUAL: White balance is fixed to the settings by R_GAIN and B-GAIN.

This mode can be used only when the color temperature does not vary.

• OFF : Normal display without mirroring or flipping

• Hor. : Video is reversed left and right

• Ver. : Video is reversed upside down.

• HV : Video is reversed left and right and upside down. When the video is

reversed by Ver. or HV, then the joystick directions are reversed accordingly.
This feature is very useful when a camera is installed upside down.

: Reverses the video left and right and/or up and down by MIRROR/FLIP.

7-1. MIRROR/FLIP

(default: OFF)

: ATW, ATWext, ONE PUSH and MANUAL are available for the white balance
modes.

6-1. WHITE BAL

(default: ATW)

SPECIAL

MIRROR/FLIP
PRIVACY
MOTION
PIXEL DEFECT
TITLE SET
DISPLAY
DEFOG
POINTING ZOOM
PRESET ZOOM
RETURN

OFF
OFF
OFF
OFF

OFF
OFF
OFF

RET

7. SPECIAL

: Adjusts the sharpness of video.

6-2. SHARPNESS

(default: 10)

: Adjusts the color level of video.

6-3. COLOR GAIN

(default: 10)

: Adjusts the gamma of day time video.

6-4. GAMMA DAY

(default: 0.5)

: Select ON/OFF or AUTO for compensation of
video image.

6-5. SHADING

(default: AUTO)

21

Operating Instructions

• ZONE NUM : Set a number to select a privacy zone from 1~10.

• ZONE DISP : ON enables to display relevant privacy zone

• H-POS, V-POS, H-SIZE and V-SIZE : Adjust the size and position of zone.

• COLOR : Select the color used for masking the zone from eight colors.

• TRANSPARENCY : Defines the transparency for the mask zone.

: 10 Privacy zones which can be enabled individually by ZON DISP are
available to mask the video.

7-2. PRIVACY

• SENSITIVITY : Adjusts the detection sensitivity for motion.

Higher value increases the sensitivity to detect small motion easier. Too low
of sensitivity will cause erratic detection.

• H-POS,V-POS, H-SIZE and V-SIZE -

Adjust the size and position of the detection window.

• BLOCK DISP : ON enables to display the blocks for the detected area.

• MOTION OSD : ON enables to display a text message, MOVING !!!,

• SMART MOTION ZOOM : ON enables to Automatic Zoom IN/OUT when motion

is detected and also enables MOTION OSD to ON.
Area to be zoomed in by SMART MOTION ZOOM can be set at SPECIAL>
MOTION> SMART MOTION ZOOM>ZOOM TARGET. Adjusting◀,▶(Joystick)
for ZOOM TARGET varies the viewing angle to be zoomed when motion
occurs. Set the video left and right and/or up and down by MIRROR/FLIP.

: MOTION can detect the changes in the motion window and displays the results
in blocks and/or a text message.

7-3. MOTION

(default: OFF)

MOTION

SENSITIVITY
H-POS
V-POS
H-SIZE
V-SIZE
BLOCK DISP
MOTION OSD
SMART MOTION ZOOM
STAY ZOOMING
RETURN

10
5
40
25
OFF
OFF
OFF
5sec

RET

|:::::::|::::::| 10

22 23

Operating Instructions

• STAY ZOOMING : Sets the duration time for zooming by Motion.

: Detects and compensates the white pixels which become defective.
Once CALIBRATE is selected, the pixel calibration is initiated with lens closed
and cannot be cancelled. (See page 25 for additional details/instructions.)

7-4. PIXEL DEFECT

(default: OFF)

: Camera title (name) can be set and edited up to 15 alpha numeric and symbolic
characters from ASCII codes (ENGLISH only). ▲,▼,◀,▶ moves the cursor to
next input. Choose a character and ‘☟’selects it. The selected characters are
added and displayed on the top left Corner and the cursor moves right
automatically for next input.

7-5. TITLE SET

※SMART MOTION ZOOM does not work in low light conditions and BW.

• THRESHOLD : Defines the level of detection.
Be sure to set the value so that the pixels are uniformly blinking over the entire
screen. Too low of a value will get a bad results because too many pixels are
detected as bad pixels and the maximum number of pixels for compensation
will be filled by the upper area.

• EXECUTE ‘☟’: Long pressing will execute the pixel calibration for the detected
pixels. Menu will exit automatically after compensation.

• Set the direction of video by MIRROR/FLIP before setting SMART MOTION

ZOOM. Otherwise ZOOM TARGET could be different from your intention.

CAUTION

• SP - Space is inserted when pressed ‘●’

• BS – Cursor moves back when pressed ‘●’

• CLR – Clears all the characters on input line when pressed ‘●’.

• POS – To be able to set the title position by ▲,▼,◀,▶ and ●.

: Enables or disables the OSD display.

• ID : ON enables camera ID display defined by SYSTEM>COMM.

SETUP>CAM ID.

• TITLE : ON enables camera ID display set by SPECIAL>TITLE SET.

7-6. DISPLAY

23

Operating Instructions

• ZOOM RATIO : ON enables to display the zoom ratio on the bottom right

corner. OZx.x appears during the optical zoom and DZx.x will display by
multiplying the optical zoom ratio and the actual digital zoom ratio.

• FOCUS INDICATE : * mark on the bottom right corner indicates the focusing
status in blue during focusing and white after finishing.

• MANUAL : Sets to enhance foggy video manually regardless of status

of scene.

• LEVEL : LOW, MID, HIGH

Video quality can be less in normal environments.

• AUTO : Enhance foggy video automatically according to status of scene.

7-7. DEFOG

(default: OFF)

ON enables to set off-centered location to be the center of zoom H-POINTER,
V-POINTER- Able to set the location of zoom center D-Zoom is available to
~ 32x. (See page 26 for additional details/instructions.)

7-8. POINTING ZOOM

Able to zoom into a preset location using the PTZ functions.

7-9. PRESET ZOOM

• Set the direction of video by MIRROR/FLIP before setting POINTING ZOOM.

Otherwise location of zoom center could be different from your intention.

CAUTION

PRESET ZOOM

ZONE NUM
ZONE VIEW
H-POS
V-POS
O-ZOOM RATIO
D-ZOOM RATIO
STAYING ZOOMING
RETURN

1
ON

5
5

3sec

OX2.0
DX2.0

RET

By Remote Controlloer only.

• ZONE NUM : Select Preset zone number 1~4.

• ZONE VIEW : ON displays selected zone preset view.

• H-POS and V-POS : Adjust the size and position of the preset zone.

24 25

Operating Instructions

• CAM ID – Assigns the camera ID from 1~255 for the comm. address.

• BAUD RATE – Selects the baud rate from 2400~115200.

• PROTOCOL – Selects the comm. Protocol from PELCO-D/P or VISCA.

8-1. TV SYSTEM

(default: US or EU)

: Selects HDTV standards for US
(60HZ) or EU(50HZ). By this
selection, 2nd analog video
output switches to NTSC or PAL
accordingly.

8-3. COMM. SET UP

: COMM. SETUP defines the CAM ID, BAUD RATE and PROTOCOL.
Data length, stop bit and parity are fixed to 8bit, 1stop bit and no parity bit.

8-4. LANGUAGE

(default: ENG)

: 8 languages are available ENGLISH, TURKISH, GERMAN, FRENCH,
ITALIAN, SPANISH, POLISH and JAPANESE.

8-5. FACTORY DEFAULT

(default: NO)

: RECALL ☟reloads and saves the factory defaults.

8-2. RESOLUTION

(default: 1080P)

: Three resolutions,1080P/720P(SCALED)/720P(CROPPED) are available.
1080P outputs 1920x1080 video at the frame rate of 30P/25P.
720P(SCALED) Image is scaled down from 1080P and outputs 1280x720
video without loss of field of view at the frame rate of 30P/25P.
720P(CROPPED) image is cropped at the center area from the image sensor
and outputs 1280x720 video at the frame rate at 60P/50P but the image refresh
rate is 30P/25P. Cropped image has narrowed field of view

SYSTEM

TV SYSTEM
RESOLUTION
COMM. SETUP
LANGUAGE
FACTORY DEFAULT
RETUTN

EU(PAL)
1080P

ENG☟
NO

RET

8. SYSTEM

( Refer to ‘TIP’ for setting RS-485 communication with PTZ Controller)

• O-ZOOM RATIO: Set the Optical Zoom Ratio from OX 1.1~OX3.0(OX2.4)

• D-ZOOM RATIO: Set the Digital Zoom Ratio from DX 1.1~DX5.0

• STAYING ZOOMING : Sets the duration time for preset zoom area.

25

UNLIKE the conventional zoom which can zoom in/out the center area of image
only, the flexible zoom location and area, SMART MOTION ZOOM differentiates
its usefulness from others.
That is, a conventional camera installed in the corner of the ceiling can zoom
the center of the floor in a room and result in losing the image of a door on the
side wall. However, SMART MOTION ZOOM can be set to see the door side
and zoom in that area without missing the IMPORTANT security point.

• H-POS (10) - Moves MOTION ZOOM area(Yellow window) horizontally

• V-POS (10) - Moves MOTION ZOOM area(Yellow window) vertically

• O-ZOOM RATIO (OX2.0) - Sets the area size to be Optically zoomed when

motion occurs in the black window

• D-ZOOM RATIO (DX2.0) - Sets the area size to be Digitally zoomed when

motion occurs in the black window

• MOTION CHK COUNT (2) - SMART MOTION ZOOM is activated after the

motion in MOTION CHK COUNT are detected in a certain period.
For example, SMART MOTION ZOOM is activated after set # of triggers by
motion.

Operating Instructions

Detail Function Description

SMART MOTION ZOOM enlarges the area defined by a yellow window
to a full size image when motion is detected in the black window.
SMART MOTION ZOOM window can be re-sized by adjusting D-ZOOM RATIO
and moved by H-POS and V-POS

▐ SMART MOTION ZOOM

SMART MOTION ZOOM

ZONE VIEW

H-POS

V-POS

O-ZOOM RATIO

D-ZOOM RATIO

MOTION CHK CUNT

RETURN

OFF

10

10

OX2.0

DX2.0

3

RET

26 27

This camera has a very useful and powerful feature, POINTING ZOOM, which
can zoom in/out any area.

POINTING ZOOM is the ability to zoom into an off center location using the PTZ
Zoom in/out feature when connected via RS485
Use H-POINTER and V-POINTER to move the Yellow box to set the position of
the center of the Zoom.
UNLIKE the conventional zoom which can zoom in/out the center area of image
only, the flexible zoom location and area, POINTING ZOOM differentiates
its usefulness from others.
That is, a conventional camera installed in the corner of the ceiling can zoom the
center of the floor in a room and result in losing the image of door on the side
wall. However, POINTING ZOOM can be set to see the door side and zoom in
that area without missing the IMPORTANT security point.

▐ POINTING ZOOM

• H-POINTER (10):
Sets the horizontal location of area to be zoomed by POINTING ZOOM.

• V-POINTER (10):
Sets the vertical location of area to be zoomed by POINTING ZOOM.

Set D-Zoom Pointer

H-POINTER

V-POINTER

RETURN

10

10

RET

Operating Instructions

27

* SMART MOTION and POINTING ZOOM VS. Conventional Zoom

Smart Motion and Pointing Zoom

Conventional Zoom

Operating Instructions

28 29

● Move the cursor in the MENU :

Moves UP/DOWN/LEFT/RIGHT Joy stick

Operating Instructions

● Enter the MENU :

Press buttons 9+5+PSET (PRESET)

● Select or Choose value in the MENU :

Press button OPEN (IRIS OPEN)

● Set the Preset Zoom :
Press buttons 1(or ~4)+PSET (PRESET)

● Exit the Preset Zoom mode :
Press buttons 3+4+PSET (PRESET)

TIP

Setting for Zoom Function with PTZ Controller

1

43

● D-Zoom IN: Press button TELE or Spin
the joystick to clockwise.

● D-Zoom OUT: Press button WIDE or Spin
the joystick to counter-clockwise.

29

Detailed Specifications VTC-BHOCRAZE39 VTC-BHOCRAZE922

Sensor
Resolution
S/N
Video Output
IR Illuminators
IR Color Temp.
IR Range
Dynamic Intensity Smart IR LEDs
Lens
Auto Focus Zoom
Digital Zoom
Minimum Illumination
Day/Night
Electronic shutter speed
White Balance
Brightness
DSS (Sens-Up)
DNR
WDR
Privacy Zones
Motion Detection
ACE (Adaptive Color Enhancement)
Advanced OSD Functions

Communication
HD Transmission Range
Weather Resistance Rating
Cooling Fan
Operating Conditions
Input Voltage
Power Consumption (12VDC)
Power Consumption (24VAC)
Dimensions

1/3” Progressive Scan CMOS Sensor

2.1 MegaPixel (1080p / 720p)
More than 50 dB (AGC Off)

Selectable: 1x HD-SDI (BNC) / EX-SDI (BNC)

40 IR LEDs

850nm

150’
YES

0 ~ x32

0.0008 Lux (@AGC MAX DSS x2)
TDN with dual filter switch

Auto (1/ 30sec ~ 1/ 60,000sec)

ATW / ATWext / One Push / Manual

YES

OFF / AUTO / X2 ~ X32

3D-DNR

Preset or Custom Scene/Level Select

YES (10 Zones)

YES
YES

Motion Activated Pointing Zoom, Defog, Dynamic IR, BLC/HLC, Motion Deblur, Pixel

Defect Compensation, Title Set, Mirror, Flip,Lens Refresh, Lens Initialize, DSS, LED

ON/OFF control

RS-485 (Pelco® D/P)

Extended Range Beyond 1000’ with RG59U 95% Copper Braid Coax

IP-68

Built-In Cooling Fan

-22°-122°F (-30°-50°C) < 80% RH
12VDC / 24VAC (Dual Voltage)

650mA (7.8Watt)

500mA (6Watt)

4.375” x 3.875” x 10.875” (W x H x D)

MegaPixel IR Corrected 3-9mm AFZ

YES - 3x Smart Motion Zoom

MegaPixel IR Corrected 9-22mm AFZ

YES - 2.4x Smart Motion Zoom

30 31

VT-HDOCE Series

On Cue Series 4, 8, and 16 Channel Real Time
1080p EX-SDI Digital Video Recorders

• 4, 8 OR 16 CH EX-SDI / Analog Inputs (hybrid) with Full 1080p Camera Support

• Now Supporting Cable distance of up to 1000’ using RG59!*

• Hybrid Operation over COAX for HD-SDI, 960H, and D1 Cameras

• Simple plug and play, point-to-point connection from camera to DVR

• Real Time Recording on all channels at 1080p (VT-HDOC4E: 120fps),
(VT-HDOC8E: 240fps), (VT-HDOC16E: 480fps)

• HDMI, VGA, and Spot BNC Outputs

• Up to 5 Internal SATA2/SATA3 HDD Slots supporting up to 20TB (5 x 4TB HDD)
using Advanced HDD Format

• External SATA Port (eSATA) Supporting up to 5x External via eSATA

• Pentaplex Operation (Playback, Recording, Backup, Network)

• Alarm In/Out

• Per channel Image Adjustment

• 4 Channel Audio In

• 32 x 24 Motion Detection Grid

• Multi channel Spot output

• Panorama (Thumbnail) Search

• Remote Viewing via CMS Software, Internet Explorer, and Mobile Phones (iOS/
Android), Mac OSX App

• Linear digital zoom for live and playback

• Up to 7 Simultaneous Network/Remote Connections

• 256 Camera Remote Viewing via CMS Software

• RS485 Communication port

CONSIDER THESE OTHER
GREAT PRODUCTS FROM

31

LIMITED PRODUCT WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of any
rightful claim of infringement or the like, and when used in the manner
intended, will be free of defects in materials and workmanship for a
period of three (3) years, or as otherwise stated above, from the date of
purchase by the end user. This warranty is nontransferable and extends
only to the original buyer or end user customer of a VITEK Authorized
Reseller.

The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the
guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
VITEK Authorized Reseller.

VITEK

28492 Constellation Road ValenCia, Ca 91355

WWW.ViteKCCtV.CoM

Version 1.0

June 2015