Vita-Mix Inc. 1440, 1441, XRM010 Installation Manual
ATTENTION
COMPONENT
Turn off water supply and disconnect Rinse-o-matic
from faucet after closing time. Periodically check
water supply hose and connections for leakage.
PRESSURE REGULATOR KIT
MANUFACTURED BY VITA-MIX®CORPORATION
1
2
This package contains one item #1439 which includes the following:
AME
FIGURE
N
TY.
Q
ITEM NUMBER
1. HOSE ASSEMBLY INLET (Female Connection) 1 1440
2. WATER PRESSURE REGULATOR 1 – – –
3. HOSE ASSEMBLY OUTLET (Male Connection) 1 1441
4. INSTALLATION INSTRUCTIONS (Not Shown) 1 XRM010
Use the above item #s for ordering replacement parts.
3
INSTALLATION INSTRUCTIONS
PLEASE NOTE: This equipment is to be installed to comply with the applicable Federal, state, or local plumbing
codes having jurisdiction.
1. Ensure that you have received all of the parts in the diagram. If you are missing any parts, please contact
the Vita-Mix Corporation at
Latin America, contact your local Vita-Mix Distributor or telephone the Vita-Mix International Division at
+1 440-782-2450.
2. Make sure that the faucet is turned off.
3. Remove the Rinse-o-matic¨ hose
4. Unscrew the male quick disconnect (Item 2) from the Y-connector (Item 3) or from the faucet if the
Y-connector is not being used.
5. Screw the female end of the pressure regulator assembly
to the faucet if the Y-connector is not being used. (Make sure the rubber washer is inside the female end
before tightening.)
6. Screw the male quick disconnect insert
7. Check all connections to ensure they are tight.
8. Reattach the Rinse-o-matic hose
9. Turn on the cold water and use the Rinse-o-matic as intended.
800-437-4654 or 440-235-0214. If you live outside of the U.S., Canada or
(Item 1) from the male quick disconnect insert (Item 2).
(Item 4) to the Y-connector (Item 3) or directly
(Item 2) to the male end of the regulator assembly (Item 4).
(Item 1) to the male quick disconnect insert (Item 2).
Item 4
Assembly #1439
Male End
Item 2
Item 1
To Rinse-o-matic
To Faucet
Item 3
Female End
Pressure Regulator
LIMITED ONE-YEAR WARRANTY
Vita-Mix®Corporation will repair or replace this product with new or rebuilt parts, free of charge, in the USA, Puerto Rico and Canada, in the event of a defect in materials or workmanship for a period of one year from the date of purchase.
This warranty does not cover damage which occurs from shipment, accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustments, improper maintenance, alterations, modifications, tampering,
negligence, lack of reasonable care, water power, acts of God, or repair or service by anyone other than a service facility authorized by Vita-Mix. Replacement nozzle parts, seals, suction cups, hoses and connectors are available for a reasonable
cost. Vita-Mix Corporation shall not be liable for the loss of use of the product, inconvenience, loss or any other damages, whether direct, incidental, or consequential including, without limitation, damage to other equipment resulting from
the use of this product, or arising out of any breach of this warranty.
This limited warranty is in lieu of any other warranty expressed or implied. No representative or any other person is authorized to make any other warranty or to assume liability not strictly in accordance with the foregoing. This limited
warranty gives you specific legal rights which may var
Vita-Mix Rinse-o-matic Service Center
Regulator Kit, make sure it is properly packaged to avoid damage. Transportation is the user’s responsibility.
Outside the United States, Puerto Rico and Canada other warranties may apply. Contact your local Vita-Mix distributor for details or telephone Vita-Mix International at +1 440-782-2450.
, 8615 Usher Rd., Cleveland, Ohio 44138-2103 USA. In order to receive warranty ser
y from state to state. T
o obtain warranty service in the United States, Puerto Rico and Canada call the Vita-Mix Service Hot Line toll free at 800-437-4654, 440-235-0214 or write
vice you may be required to provide proof of purchase. Should it become necessar
y to transport your Rinse-o-matic
PRESSURE REGULATOR KIT
MANUFACTURED BY VITA-MIX®CORPORATION
Instructions for external sanitizing of the Rinse-o-matic with Regulator Kit
1. Make sure the water supply is off and disconnect the unit from the water supply.
2. Place the unit in a basin of warm (110˚ F / 43˚C), clean water.
3. Add a mild dishwashing soap to the water according to the soap’s recommended concentration.
4. Wash all surfaces with a soft cloth.
5. Wash hard to reach areas with a small, soft brush.
Instructions for internal sanitizing of the Rinse-o-matic with Regulator Kit
1. Make sure the water supply is off and disconnect the regulator assembly from the water supply.
2. Relieve the residual water pressure in the unit by depressing the spray head plunger with a container.
3. Add a mild dishwashing soap to the female end of the regulator assembly to a 3/8” / 10 mm depth.
4. Taking care not to spill any dishwashing soap, reconnect the regulator assembly to the faucet.
5. If you are using the Y
and the opposite valve is off. Turn the hot water supply on for approximately 5 seconds and shut it back
off. This flushes the soap into the Rinse-o-matic unit.
Let the unit sit for a period of time determined by the soap manufacturer’s recommendations. During this
6.
time, you can disconnect the unit from the faucet and put it aside, but do not depress either of the
plungers as this would relieve the internal pressure. The internal pressure aids in cleaning.
7. Reconnect the unit to the faucet, and turn on the hot water supply.
8. Depress the sprayhead plunger for approximately 20 seconds to flush out the soap.
9. Repeat steps 1 through 9 at least two more times.
-connector, make sure that the valve controlling the flow to the Rinse-o-matic is on
TROUBLESHOOTING
A. The unit leaks at the hose connections.
1. Screw the male quick disconnect insert to the regulator kit assembly tightly by hand. Be sure not to
over-tighten.
2. Screw the female hose end of the regulator kit assembly tightly by hand. Make sure the rubber
washer is inside the female end before tightening. Be sure not to over-tighten.
3. If the previous steps do not solve the problem, please contact Vita-Mix¨ Customer Service at
800-437-4654 or 440-235-0214.*
B. Water does not flow or the water pressure is very low.
1. Ensure that the faucet is on.
2. Ensure that the valve on the leg of the Y-connector that supplies the Rinse-o-matic with water
is on and that the valve on the opposite leg is off when attempting to use the Rinse-o-matic.
3. If the water supply line that supplies the Rinse-o-matic is used to supply water to any other
equipment, make sure that equipment is not drawing water when attempting to use the
Rinse-o-matic.
4. If the previous steps do not solve the problem, please contact Vita-Mix¨ Customer Service at
800-437-4654 or 440-235-0214.*
*Outside the United States, Canada or Latin America contact your local Vita-Mix distributor or telephone the Vita-Mix International Division at +
©2005 Vita-Mix Corporation Printed in the U.S.A. XRM010 08/05
440-782-2450.
1
Loading...