Vita The Nantucket Legacy Arbor ASSEMBLY INSTRUCTIONS

ASSEMBLY

INSTRUCTIONS

The Nantucket Legacy Arbor / Arch

102.25 in

259.7 cm

*Nantucket Legacy with Trim Kit Shown Above.

Please read through before starting assembly.

IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.

95 in

241.3 cm

52 in / 132.1 cm

60 in / 152.4 cm

172.7 cm

68 in

71 in

180.3 cm

www.wearevita.com

102.25 in

259.7 cm

20 in

50.8 cm
28 in

71.1 cm

Check Box for These Contents

In the event of missing or defective parts please call our customer service dept. at

1. Keystone Top Lid (2) - 10710-1

2. Keystone Internal Connectors (2) - 10711-1

3. Arch Keystones (2) - 10684-1

4. Keystone Bottom Plate (2) - 10712-1

5. Arches (4) - 10687-1

6. Arch Rafters (8)

7. Post Caps (4) - 10728-1

8. Side Panel Horizontal Rails (4)

9. Posts (4) 4’x4‘x70.5“

10. Side Panel Diamond Lattice (2) - 10776

11.

#8 x

1 1/2 in. (3.8 cm.)

Connection) (24) - 20005

If you purchased the arbor / arch along with our decorative trim kit (BP80001),
there will be a separate box with the following contents;

12. Post Trim Caps (4)

13. Base Molds (4)

1 1/2” x 1 1/2” x 25.9" [3.8 x 3.8 x 65.8 cm] - 10778

1 1/2” x 1 1/2” x 27.7” [3.8 x 3.8 x 70.4 cm] - 10777

[10.2 x 10.2 x 179.1 cm] - 10775

Stainless Steel Screws

(for Keystone and Arch to Post

Tools You Will Need

• Hammer

• Tape Measure

• Level

• Stool or Short Ladder

• Shovel or Auger

• Cordless Drill

12

13

General Information

• Read Instructions through carefully before beginning assembly.

• When assembling components, place on a non-abrasive surface

(i.e. shipping box) to avoid scratching.

• We recommend an area approx 10’x 8’
assembling.

• You should not need to use excessive force when assembling components.

(3 m x 2.4 m) for unobstructed

1 800 282 9346

1

2

3

4

5

6

7

8
9

10

(Mon. to Fri. 8:00 AM to 5:00 PM EST).

11

(Not to scale)

V2.5_111020

1

STEP ON E

Assemble the Arch System

NOTE: There are locking tabs located at the ends of each
rafter. Once inserted and pushed into the routed holes, they
will lock into place and cannot be removed.

Insert arches into arch keystone ensuring they terminate

1

flush to the internal connector.

Fasten the top of the arches to the keystone insert by

2

installing 1 1/2 in. (3.8 cm.) screws into the two flanges on
either

side of the top of internal connector.

Invert the arch system and install four screws 1 1/2 in. (3.8 cm.)

3

from the bottom of the keystone into the two
either side of the bottom of the internal connector. This will
connect the bottom

Seal the bottom hole on keystone by inserting the bottom

4

plate as provided.

Install the top cap on the arch keystone.

5

cap is pushed down firmly so the cap locks into position.

Repeat for other arch.

6

Insert arch rafters (8) into the holes on the arches until they

7

bottom out inside the arches. There are “locking tabs” located

at each end of these rafters that once inserted into the holes
will lock into place.

of the arches to the insert.

flanges on

Ensure keystone

1

2

3

Fit opposite arch system over rafters.

8

7

4

5

8

2

The Nantucket Legacy Arbor / Arch