Visual Comfort & Co. CHO2112 Assembly Instructions Manual

Download

ASSEMBLY INSTRUCTIONS

WE RECOMM END I NSTALLATION OF THIS LIG HTING FIXTUR E BE DONE BY A LICENS ED ELECTR ICIAN.

WARNING *** SWITCH OFF TH E MAIN ELECTRI CAL SUPPLY FROM THE MAIN FUSE BOX/CIRCU IT BREAKE R BEFOR E INSTALLATION.

INS PECT ITEM CAREFULLY BEFOR E ATTEMPTING TO INSTALL. IF THE RE IS ANY DAMAGE OR OBVIOUS DE FECT, DO NOT INSTALL.

ITEM MAY NOT BE RETURN ED ONCE IT HAS BE EN INSTALLED.

1. Remove back plate (B) from ﬁxture base (F) by unscrewing washers/cap nuts

(E) in counter-clockwise direction.

2. Position back plate (B) onto outlet box (A) in desired orientation and use it as a

template, mark locations for four comer holes on the wall. Install plastic anchors

(U) on the marked location.

3. Remove screw and washer (H) from supported band (G) in counter-clockwise

direction. Remove lantern caps (R) & (P) by unscrewing screws/washers (N)

& (S).

4. Attach ground (green) ﬁxture wire to ground wire from wall outlet box (usually

green or copper in color), and fasten together with a plastic wire connector.

Tightly wrap the wire connector with electrical tape so the end of the connector

is sealed. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOM E BE

PROPERLY GROUNDED.

5. Connect neutral (white) ﬁxture wire to neutral (usually white) wire from wall

outlet box. Fasten both wires together with a plastic wire connector and tightly

wrap the wire connector with electrical tape.

6. Repeat the procedure with the hot (black) wires. Always make sure that no wire

strands are left outside the connectors. DO NOT REVERSE THE HOT AND

NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISE D.

7. Gently push lantern box ﬁxture (J) onto outlet box (A), letting rods (D) pass

through the holes on ﬁxture base (F).

8. Position the light ﬁxture and tighten by screwing cap nuts (E) to the exposed

part of rods (D) in clockwise direction.

WET

Chelsea Large Lantern

Item # CHO2112

WE RECOMMEN D INSTALLATION OF THIS LIGHTI NG FIXTURE BE DONE BY A LICENSED ELECTR ICIAN.

WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUS E BOX/CIRCUIT BREAKER BE FORE INSTALLATION.

INS PECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THER E IS ANY DAMAGE OR OBVIOUS DE FECT, DO NOT INSTALL.

ITEM MAY NOT BE RETURN ED ONCE IT HAS B EEN INSTALLED.

1. Remove back plate (B) from ﬁxture base (F) by unscrewing washers/cap nuts (E) in counter-clockwise direction.

2. Position back plate (B) onto outlet box (A) in desired orientation and use it as a template, mark locations for four

comer holes on the wall. Install plastic anchors (U) on the marked location.

3. Remove screw and washer (H) from supported band (G) in counter-clockwise direction.

4. Remove lantern caps (R) & (P) by unscrewing screws/washers (N) & (S).

5. Attach ground (green) ﬁxture wire to ground wire from wall outlet box (usually green or copper in color), and

fasten together with a plastic wire connector. Tightly wrap the wire connector with electrical tape so the end of the

connector is sealed. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PROPERLY GROUNDED.

6. Connect neutral (white) ﬁxture wire to neutral (usually white) wire from wall outlet box. Fasten both wires together

with a plastic wire connector and tightly wrap the wire connector with electrical tape.

7. Repeat the procedure with the hot (black) wires. Always make sure that no wire strands are left outside

the connectors. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE

COMPROMISED.

8. Gently push lantern box ﬁxture (J) onto outlet box (A), letting rods (D) pass through the holes on ﬁxture base (F).

9. Position the light ﬁxture and tighten by screwing cap nuts (E) to the exposed part of rods (D) in clockwise direction.

10. To install glass panel (0) provided to front door (K), make sure metal tab (L) is ﬂipped up. Insert glass panel to front

frame, secure the glass panel by bending back the metal tab (L) downwards. Insert the other three glass panels (0)

into the other three side of the lantern box.

11. Place glass panels (Q) to four sides of lantern box cap (R) and secure by bending back the metal tabs downwards.

12. Replace lantern box caps (R) & (P) on top of lantern box (J) and secure with brass bands and washers/

13. screws (S) & (N). Align the holes on both support band (G) and ﬁxture base (F), insert screws (H) into the holes and

tighten with screwdriver. Insert light bulb into socket. Close front door (K) and secure with key (M).

ASSEMBLY INSTRUCTIONS

WE RECOMM END I NSTALLATION OF THIS LIG HTING FIXTUR E BE DONE BY A LICENS ED ELECTR ICIAN.

WARNING *** SWITCH OFF TH E MAIN ELECTRI CAL SUPPLY FROM THE MAIN FUSE BOX/CIRCU IT BREAKE R BEFOR E INSTALLATION.

INS PECT ITEM CAREFULLY BEFOR E ATTEMPTING TO INSTALL. IF THE RE IS ANY DAMAGE OR OBVIOUS DE FECT, DO NOT INSTALL.

ITEM MAY NOT BE RETURN ED ONCE IT HAS BE EN INSTALLED.

9. To install glass panel (0) provided to front door (K), make sure metal tab (L) is

ﬂipped up. Insert glass panel to front frame, secure the glass panel by bending

back the metal tab (L) downwards. Insert the other three glass panels (0) into

the other three side of the lantern box.

10. Place glass panels (Q) to four sides of lantern box cap (R) and secure by

bending back the metal tabs downwards.

11. Replace lantern box caps (R) & (P) on top of lantern box (J) and secure with

brass bands and washers/

12. screws (S) & (N). Align the holes on both support band (G) and ﬁxture base (F),

insert screws (H) into the holes and tighten with screwdriver. Insert light bulb

into socket. Close front door (K) and secure with key (M).

INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET

LOCATION:

1. Mounting surface should be clean, dry, ﬂat and 1/4” larger than the backplate

on all sides. Any gaps between the mounting surface and backplate exceeding

3/16” should be corrected as required.

2. With silicone (ex. GE-108) caulking compound, caulk completely around where

back of the backplate meets the wall surface to prevent water from seeping into

outlet box.