Vista VPM8130, VPM8120, VPM8030, VPC9132-CM, VPC9132 User Manual
...
VPM8030
VPM8032
VPM8130
VPM8132
VPM8120
VPM8122
VPC9030
VPC9032
VPC9130
VPC9132
VPC9032/CM
VPC9132/CM
Protos 3 Series Cameras
Installation Instructions
Read these instructions first!
Installation Instructions
0
“
0.8
1.0
INTRODUCTION
Read all of these instructions. Use them to install your camera and have them available for its
lifetime. If you have any problems, contact your agent. Note that not all cameras have all of the
features described in this manual. Refer to the table below for the features of individual
cameras. All cameras are fitted with a Direct Drive (DD) lens connector, an Auto Iris (AI)
connector, have adjustable back focus and accept C and CS lenses.
VPC9032/CM and VPC9132/CM series cameras are designed to give a good image over a
broad range of scene illumination. To achieve this, the camera operates in colour mode where
the scene illumination is bright and automatically switches to monochrome where the scene
illumination is low. Typically, the switchover occurs at approximately 2.0 lux.
TABLE 1
Option
VPM8030
VPM8032
VPM8120
VPM8130
VPM8122
VPM8132
VPC9130
VPC9132
VPC9032/CM
VPC9030
VPC9032
VPC9132/CM
Mono
Color
Color/Mono
Resolution (TVL)
Sensitivity (lux @ f1.2)
CCD Sensor size
380 380 570 570 480 480 330 48
0.1 0.1 1.00.1 0.1 1.0
0.1 0.9
1/3“ 1/3“1/3“ 1/3“
1/3“ 1/2“ 1/3“1/3“ 1/2“ 1/3“ 1/3“ 1/3
0.1
570570 330 330
0.9
2.0 2.0
Sony SuperHAD™ CCD
DSP Digital Signal Processing
Adjustable Gamma (0.45 and 1.0)
Automatic Gain Co n trol (AGC)
Backlight Compensation (BLC)
BLC on/off
Electronic Iris (EI)
EI on/off
Auto Iris connection
Line lock with phase adjust (AC only)
Internal Sync.
Supply
11 - 40 VDC; 14 - 30 VAC
98 - 260 VAC
Note: NTSC and EIA camera models have suffixes /N and /E respectively. These variants
are also covered by Table 1.
2
Installation Instructions
PRODUCT SAFETY
Installation and servicing is only to be carried out by suitably qualified and
experienced personnel.
Mains cameras contain hazardous voltages.
Do not remove covers as there is a risk of injury or death by electric shock.
Cameras connected to mains supplies must be earthed.
Only power low voltage cameras from a class 2 isolated power supply.
This camera range is designed for use in general purpose CCTV applications and has no other
purpose. Only operate your camera between the temperatures of -10
O
C and +50OC. Do not
operate your camera outside its specified power supply range. Cameras must only be used in
clean, dry, dust-free environments unless housed in suitable protective housings to IP65 or
better.
ELECTROMAGNETIC COMPATIBILITY (EMC)
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This product is intended solely for use in general CCTV applications.
The product must be installed and maintained in accordance with good installation practice to
enable the product to function as intended and to prevent problems. Refer to Norbain SD Limited
for installation guidance.
MANUFACTURERS DECLARATION OF CONFORMANCE
The manufacturer declares that the equipment supplied with this manual is compliant with the
essential protection requirements of the EMC directive 89/336 and the Low Voltage Directive
LVD 73/23 EEC. Conforming to the requirements of standards EN 55022 for emissions, IEC801
parts 2, 3 and 4 for immunity and EN 60950 for Electrical Equipment safety.
3
Installation Instructions
CAUTIONS
In order to avoid damaging the camera note the following points:
1) The camera has threaded mounting points on the top and bottom of the case.
Only use a standard, photographic, mounting-bolt with a 1/4 20 UNC thread.
2) Before fitting the lens make sure that its back will not touch the CCD sensor or
associated components when screwed fully home.
3) Do not touch the image-surface of the sensor. If the sensor is accidentally
touched, only clean it using ethyl alcohol.
4) Do not expose the camera sensor to very bright light over a long period of time
as this may cause damage to the CCD. The camera and lens set-up must be
correct to avoid continual over exposure by bright light.
5) The weight of your camera is 0.5kg (0.35kg for low voltage versions).
6) Only use your camera in a clean, dust-free environment.
7) For outdoor use, an appropriate protective housing conforming to IP65 or UL50
or better must be used.
POWER SUPPLY
Cameras are available in AC mains and AC and DC low voltage types. The voltage required
to operate the camera is clearly marked on the rear panel of the camera. Only
power low voltage cameras from a class 2 isolated power supply. The typical power
consumption of a VP... series camera is less than 5 Watts.
Mains Power Supply
Cameras that are intended to operate directly from the mains supply are fitted with a nondetachable power supply cord. The voltage of operation is clearly marked on the rear panel of
the camera. Generally this is 98 to 260 VAC at 50 Hz for CCIR/PAL (60Hz for EIA/NTSC).
REFER TO THE WIRING INSTRUCTION LABEL ATTACHED TO THE SUPPLY CORD and terminate
the cord with the appropriate circuit fitted with a 3A fuse.
MAINS CAMERAS MUST BE CONNECTED TO A PROTECTIVE EARTH GROUND. Ensure that
a secure means of isolation from the mains is provided for the camera in accordance with the
national wiring regulations of the country of installation.
Auto-Switching Power Supply
Cameras fitted with an automatic selecting power supply operate between 11-40 VDC and
14-30 VAC. Connections and polarity are indicated above the screw terminals on the rear
panel. The power supply must be a class 2 isolated type.
4
Loading...