Vista VPC5-704DNS, VPC5-700DNS Installation Manual

Set up and user manual for the

VPC5-704DNS
VPC5-700DNS

cameras

Installation Manual

Before You Begin

Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should

conform to local codes.
This manual provides installation and operation information. To use this document,

you must have the following minimum qualifications:

 A basic knowledge of CCTV systems and components
 A basic knowledge of electrical wiring and low-voltage electrical connections

Intended use

Only use this product for its designated purpose; refer to the product specification and
user documentation.

Customer Support

For assistance in installing, operating, maintaining and troubleshooting this product
refer to this document and any other documentation provided. If you still have
questions, please contact Norbain Technical Support and Sales:

Norbain Ltd

210 Wharfedale Road, IQ Winnersh Triangle, Wokingham, Berks RG41 5TP

UK [phone] / Netherlands [phone] / Belgium [phone]

South Africa [phone] / Portugal [phone] Spain [phone]

Middle East [phone] / Rest of world [phone]

Note: You should be at the equipment and ready with details before calling Technical

Support.

Conventions Used in this Manual
Boldface or button icons highlight command entries. The following WARNING,

CAUTION and Note statements identify potential hazards that can occur if the

equipment is not handled properly:

* WARNING:
Improper use of this equipment can cause severe bodily injury or
equipment damage.

** Caution:
Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

4

RoHS Announcement

All lead-free products offered by the company comply with the
requirements of the European law on the Restriction of Hazardous
Substances (RoHS) directive, which means our manufacture
processes and products are strictly “lead-free” and without the
hazardous substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the
European Union the product must be collected separately at the
product end-of-life. This applies to your product and any peripherals
marked with this symbol. Do not dispose of these products as
unsorted municipal waste.

CE Mark

This apparatus is manufactured to comply with the radio interference.
A Declaration of Conformity in accordance with the following EU
standards has been made. The manufacturer declares that the
product supplied with this document is compliant the provisions of the
EMC Directive 2004/108/ EC, the CE Marking Directive 93/68 EEC and
all associated amendments.

* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.

NORBAIN LTD reserves the right to make changes to the product and specification of
the product from time to time without prior notice.

WARNINGS AND CAUTIONS:

To reduce the risk of fire or electric shock, do not insert any metallic objects through
the ventilation grills or other openings on the equipment.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

5

IMPORTANT SAFEGUARDS

1. READ AND RETAIN INSTRUCTIONS

Read the instruction manual before operating the equipment.
Retain the manual for future reference.

2. CLEANING

Turn the unit off and unplug from the power outlet before cleaning. Use a damp cloth
for cleaning. Do not use harsh cleansers or aerosol cleaners.

3. ATTACHMENTS

Do not use attachments unless recommended by manufactured as they may affect
the functionality of the unit and result in the risk of fire, electric shock or injury.

4. MOISTURE

Do not use equipment near water or other liquids.

5. ACCESSORIES

Equipment should be installed in a safe, stable location. Any wall or shelf mounting
accessory equipment should be installed using the manufacture's Instructions. Care
should be used when moving heavy equipment. Quick stops, excessive force, and
uneven surfaces may cause the equipment to fall causing serious injury to persons
and objects.

6. VENTILATION

Openings in the equipment, if any, are provided for ventilation to ensure reliable
operation of the unit and to protect if from overheating. These openings must not be
blocked or covered

7. POWER SOURCES

The equipment should be operated only from the type of power source indicated on
the marking label. If you are not sure of the type of power supplied at the installation
location, contact your dealer. For equipment designed to operate from battery power,
refer to the operating instructions.

8. GROUNDING OR POLARIZATION

Equipment that is powered through a polarized plug (a plug with one blade wider
than the other) will fit into the power outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the outlet, try reversing the plug. Do not
defeat the safety purpose of the polarized plug.
Alternate Warning: If the equipment is powered through a three-way grounding­type plug, a plug having a third (grounding) pin, the plug will only fit into a grounding­type power outlet. This is a safety feature. Do not defeat the safety purpose of the
grounding-type plug.
If your outlet does not have the grounding plug receptacle, contact your local
electrician.

9. CORD AND CABLE PROTECTION

Route power cords and cables in a manner so to protect them from damage by being
walked on or pinched by items places upon or against them.

10. LIGHTNING

For protection of the equipment during a lightning storm or when it is left unattended
and unused for long periods of time, unplug the unit from the wall outlet. Disconnect
any antennas or cable systems that may be connected to the equipment. This will
prevent damage to the equipment due to Lightning or power-line surges.

6

11. OVERLOADING

Do not overload wall outlets and extension cords as this can result in a risk of fire or
electric shock.

12. SERVICING

Do not attempt to service the video monitor or equipment yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.

13. DAMAGE REQUIRING SERVICE

Unplug the equipment from the wall outlet and refer servicing to qualified service
personnel under the Following conditions:
A. When the power supply cord or the plug has been damaged.

B. If liquid has spilled or objects have fallen into the Unit.

C. If the equipment has been exposed to water or other liquids.

D. If the equipment does not operate normally by following the operating

instructions, adjust those controls that are covered by the operating
instructions as Improper adjustment for other controls may result in damage

to the unit.
E. If the equipment has been dropped or the casing is damaged.
F. When the equipment exhibits a distinct change in performance.

14. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.

15. SAFETY CHECK

Upon completion of any service or repairs to the equipment, ask the service
technician to perform safety checks to verify that the equipment is in proper operating
condition.

16. FIELD INSTALLATION

The installation of equipment should be made by a qualified service person and
should conform to all local codes.

17. CAUTION - THESE SERVICING

INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY
SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

18. Use certified/Listed Class 2 power supply transformer only

CE COMPLIANCE STATEMENT

WARNING

This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required
to take adequate measures.

7

CONTENTS OF PACKAGE

Installation of the camera must be performed by qualified service
personnel in accordance with all local and national electrical and
mechanical codes.

Carefully remove the colour camera and its accessories from the
carton and verify that they were not damaged in shipment.

The content of the package includes:

1. Colour CCD camera

2. Mini-DIN connector (for video-or dc-type auto-iris lens)

3. CS adapter ring for C mounting "C" lenses

4. This manual

TABLE OF CONTENTS

INTRODUCTION ------------------------------------------------------------------------------------------------------ 9

CAMERA OVERVIEW------------------------------------------------------------------------------------------------ 11

CAMERA ADJUSTMENT ------------------------------------------------------------------------------------------- 13

CONTROL AND CONNECTIONS / DAY&NIGHT I/O TERMINALS ------------------------------------- 26

LENS… ------------------------------------------------------------------------------------------------------------------- 28

9

INTRODUCTION

Features:

 700TVL resolution
 1/3" Super-HAD CCD II (960H)
 Wide Dynamic Range
 Day & Night(Auto, Manual, External, Filter delay, Change

level adjust)

 0.1Lux (Colour), 0.01Lux (BW), 0.0001Lux (Sens-Up B/W)

@ F1.2 50IRE

 Auto Electronic Shutter [1/50 ~ 1/100,000] and manual

electronic shutter modes [1/50 ~ 1/10,000]

 Sense-Up (~x256)
 2D-NR, 3D-NR
 UDF Function(Ultra Deep Field)
 Multi Camera Configuration Set (4-Sets/Night Profile, Ext

DN Profile)

 PVA/PVA+ (Personal Video Analytics)

 Very High Configurable.
 Various Detection Methods(Motion, Loitering Object,

Abandon, Scene Change, Un-focus, Windy Area)

 Various Zone Event Detection Methods and Event Area

Combinations.

 8 Objects Trace, 4 Objects Display
 Concurrent Processing with All Detections, and All

Objects.

 Two Counting Block.
 Event String Sending (Editable String)
 Digital Tracking(Using D-PTZ)
 Various Detection Area(MAX. 10 area, Line, Rectangle,

4-Point polygonal)

 Back Light Compensation (EHLC, Auto, Spot)
 i-Freeze Function(Reduce recording space)
 Privacy Mask or Mosaic(MAX. 10 area/4-point

polygonal/transparency)

 Digital Image Stabilization.

10

 Digital PTZ
 Digital Effect (H/V reverse, 180 degree rotate, inverse,

freeze)

 White Pixel Removal.
 Focus Aid Function.
 Colour Rolling Suppression.
 System Lock (4-character password)
 C/CS, back-focus cam for easy adjustment
 Auto and Manual white balance modes
 Support Line-Lock external synchronization
 RS-485 Remote camera control
 Compatible with Video, DC type lenses with OSD select
 Quick connect for Video or DC lens with 4-pin connector
 User Certified / Listed Class 2 power source only
 Operates in 12VDC or 24VAC