Vista PVM27CAM Installation And User Manual

Installation and User Manual

PVM27CAM

b

Contents

CE INFORMATION ........................................................................................................ d

SAFETY PRECAUTIONS ................................................................ .............................. d

BEFORE YOU BEGIN ................................................................................................... e

Scope ................................................................................................ ............................ 1

Functional Specifications ............................................................................................ 2

Power Supply ........................................................................................................................................ 2

Video Characteristics ............................................................................................................................. 2

VGA Input .............................................................................................................................................. 2

Controls: Back Push Buttons ................................................................................................................. 2

HDMI Input ............................................................................................................................................ 2

Audio Input ............................................................................................................................................ 2

Environmental ........................................................................................................................................ 3

EDID ...................................................................................................................................................... 3

Controls and Indicators ............................................................................................... 3

Connectors ............................................................................................................................................ 3

Camera Lens Adjust .............................................................................................................................. 4

Remote Control ..................................................................................................................................... 5

Accessories ........................................................................................................................................... 6

OSD Menu..................................................................................................................... 7

Hot key .................................................................................................................................................. 7

Main Menu ............................................................................................................................................. 8

MAIN ADJUST ....................................................................................................................................... 9

COLOR ADJUST ................................................................................................................................. 10

SCAN SETTING .................................................................................................................................. 11

IMAGE ADJUST (VGA ONLY) ............................................................................................................ 11

INFORMATION ................................................................................................................................... 12

LANGUAGE ......................................................................................................................................... 13

SETUP MENU ..................................................................................................................................... 13

PVM FUNCTION (Video only) ............................................................................................................. 14

RECALL............................................................................................................................................... 15

AUDIO CONTROL ............................................................................................................................... 15

Multi Media Player OSD Menu ............................................................................................................ 17

Multi Media Player OSD Menu ............................................................................................................ 17

REMOTE CONTROL ..................................................................................................................... 17

CAMERA OSD Menu ................................................................................................ .. 18

REMOTE CONTROL ..................................................................................................................... 18

Regulatory Agency .................................................................................................... 24

CE COMPLIANCE: EN55022 Class B. ....................................................................... 24

EN55024. ..................................................................................................................... 24

c

EN50130-4 .................................................................................................................. 24

Reliability .................................................................................................................... 25

Mean Time Between Failures (MTBF): ................................................................................................ 25

Mechanical ................................................................................................................. 26

VESA mounting ................................................................................................................................... 27

d

CE INFORMATION

The product must be installed according to the currently valid installation regulations for EMC to
guarantee the designed use and to prevent EMC problems.
The device supplied with this manual is according to the EC, EMC Directive,
2004/108/EC & LVD 2006/95/EC

SAFETY PRECAUTIONS

1. Do not modify the three-prong grounding type monitor power plug in any way.

2. Operate this unit only from the type of power source indicated on the label.

3. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.

4. Do not place this monitor near a radiator or heating vent.

5. Do not push objects of any kind through cabinet openings. This may result in fire or electrical shock.

6. Before adding attachments always ask a service technician to perform routine safety tests to
determine that equipment is in safe operating condition. Ground potential tests should be part of the
routine safety check made by the service technician.

7. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure personnel or
damage equipment.

8. Route power cords so that they cannot be walked upon or tripped over. Do not allow anything to rest
on the power cord.

9. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not spill liquid of
any kind on the unit.

10. Unplug the power cord from the unit before cleaning the display. Use only a damp cloth. Do not use
alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO CLEAN THE INTERIOR OF

THIS UNIT- THIS ACTION MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS
REQUIRED DURING NORMAL MAINTENANCE.

11. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY
UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS VOLTAGES OR
OTHER HAZARDS.

12. Unplug the unit immediately and notify the service technician.
A. If liquid has been spilled into the display or the display has been exposed to rain or water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.
E. If a distinct change from normal operation is apparent.

When replacement parts are required, be sure that the service technician uses components specified by
the manufacturer which have the same characteristics as the original parts. UNAUTHORIZED
SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL SHOCK OR OTHER HAZARDS.

Upon completion of any service or repairs, ask the technician to perform safety checks to determine that
the equipment is in safe operating condition.

WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS MONITOR. DO

NOT OPEN THE COVERS UNDER ANY CIRCUMSTANCES,
THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE

e

BEFORE YOU BEGIN

Read these instructions before installing or operating this product.

Note: This installation should be made by a qualified service person and should conform to local codes.

This manual provides installation and operation information. To use this document,
you must have the following minimum qualifications:

A basic knowledge of CCTV systems and components
A basic knowledge of electrical wiring and low-voltage electrical connections

Intended use

Only use this product for its designated purpose; refer to the product specification and
user documentation.

Customer Support

For assistance in installing, operating, maintaining and troubleshooting this product
refer to this document and any other documentation provided. If you still have
questions, please contact Norbain Technical Support and Sales:

Vista, 210 Wharfedale Road, IQ Winnersh, Wokingham, Berkshire RG41 5TP, England.
UK [phone]

Note: You
should be at
the
equipment
and ready
with details
before calling
Technical
Support.

Conventions Used in this Manual

Boldface or button icons highlight command entries. The following WARNING,
CAUTION and Note statements identify potential hazards that can occur if the

equipment is not handled properly:

* WARNING:

Improper use of this equipment can cause severe bodily injury or equipment
damage.

** Caution:

Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

f

This apparatus is manufactured to comply with the radio interference.
A Declaration of Conformity in accordance with the following EU standards
has been made. The manufacturer declares that the product supplied with
this document is compliant the provisions of the EMC Directive
2004/108/EC, the CE Marking Directive 93/68 EEC and all associated
amendments.

All lead-free products offered by the company comply with the
requirements of the European law on the Restriction of Hazardous
Substances (RoHS) directive: 2011/65/EU, which means our manufacture
processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European
Union the product must be collected separately at the product end-of-life.
This applies to your product and any peripherals marked with this symbol.
Do not dispose of these products as unsorted municipal waste.

* This symbol indicates electrical warnings and cautions.

** This symbol indicates general warnings and cautions.

NORBAIN SD LTD reserves the right to make changes to the product and specification of the product from time to
time without prior notice.

WARNINGS AND CAUTIONS:

To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other
openings on the equipment.

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.

CAUTION

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

1

Scope

This document is used to define the performance of the LCD Public View Monitor (PVM) series.
The system supports video and PC inputs, as well as from the built-in camera. In video mode,
the display automatically detects NTSC and PAL signals. The On Screen Display (OSD) menu
makes the system easy to operate.

2

Functional Specifications

Power Supply

27” PVM Monitor Power Requirements:

Voltage: 12Vdc or 24Vdc
Current: 4 A max (12Vdc) or 2A max (24Vdc)

Use only a PSU rated at 12dc, with a minimum current rating of 4A; or 24Vdc, with a minimum
current rating of 2A

Video Characteristics

Composite Video (CVBS): 1.0Vp-p (0.5 – 1.5Vpp), Automatic switching from 75 unbalanced

Composite Video (Camera output): 1.0Vp-p (0.5 – 1.5Vpp), loop-through camera signal.

VGA Input

Analog RGB: 0.707Vrms.
Support VESA Standard Timing

termination to Hi-Z with loop-through operation.

Controls: Back Push Buttons

CHANNEL: Select the input signal

: Scrolling the cursor or adjust the value

+: Scrolling the cursor or adjust the value

MENU: Select On-Screen Display (OSD)

POWER: Switch power On/Off

HDMI Input

HDMI 1.3 Compatible Interface
HDMI Timing Modes
480i / 480p
576i / 576p
720p
1080i / 1080p

Audio Input

Signal Level: 1.0Vrms

3

Environmental

Power

PC

Video

A – DC 12V/24V IN

connector

C – HDMI

In

B – USB SLOT

D – VGA In

E – BNC connector, CVBS Loop through

out

F – BNC connector, CVBS input

G – BNC connector, Camera signal out

H – AUDIO IN: Stereo Phone Jack x1

I – SD CARD SLOT

 Temperature:
Operating: 00C to +400C
Storage: -200C to +600C
 Humidity:
Operating: 10% to 85% (non-condensing)
Storage: 10% to 95% (non-condensing)

EDID

This series of displays support EDID.

Controls and Indicators

Connectors

DC-In USB HDMI VGA Video-out ideo-in CAM-out Audio-in SD-card

(A) (B) (C) (D) (E) (F) (G) (H) (I)

4

Camera Lens Adjust

W: Adjust Camera zoom to Wide.
T: Adjust Camera zoom to Tele.
N: Adjust Camera Focus to Near.
F: Adjust Camera Focus to Far.