Vista PVM19CAM Installation And User Manual

PVM19CAM

Installation and User manual

CE INFORMATION

The product must be installed according to the currently valid installation regulations for EMC to guarantee
the designed use and to prevent EMC problems.
The device supplied with this manual is according to the EC, EMC Directive
2004/108/EC, LVD 2006/95/EC and RoHS 201165/EU.

SAFETY PRECAUTIONS

1. Do not modify the three-prong grounding type monitor power plug in any way.

2. Operate this unit only from the type of power source indicated on the label.

3. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.

4. Do not place this monitor near a radiator or heating vent.

5. Do not push objects of any kind through cabinet openings. This may result in fire or electrical shock.

6. Before adding attachments always ask a service technician to perform routine safety tests to determine that
equipment is in safe operating condition. Ground potential tests should be part of the routine safety check
made by the service technician.

7. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure personnel or damage
equipment.

8. Route power cords so that they cannot be walked upon or tripped over. Do not allow anything to rest on the
power cord.

9. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not spill liquid of any kind
on the unit.

10. Unplug the power cord from the unit before cleaning the display. Use only a damp cloth. Do not use alcohol,
spirits, or ammonia to clean the display. DO NOT ATTEMPT TO CLEAN THE INTERIOR OF THIS UNIT-

THIS ACTION MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED DURING
NORMAL MAINTENANCE.

11. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY UNAUTHORIZED
PERSONNEL MAY EXPOSE THE USER TO DANGEROUS VOLTAGES OR OTHER HAZARDS.

12. Unplug the unit immediately and notify the service technician.
A. If liquid has been spilled into the display or the display has been exposed to rain or water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.
E. If a distinct change from normal operation is apparent.

When replacement parts are required, be sure that the service technician uses components specified by the
manufacturer which have the same characteristics as the original parts. UNAUTHORIZED SUBSTITUTIONS
MAY RESULT IN FIRE, ELECTRICAL SHOCK OR OTHER HAZARDS.

Upon completion of any service or repairs, ask the technician to perform safety checks to determine that the
equipment is in safe operating condition.

WARNING:

SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS MONITOR. DO NOT OPEN THE
COVERS UNDER ANY CIRCUMSTANCES,

THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE

CAUTION - USE RECOMMENDED MOUNTING APPARATUS TO AVOID RISK OF INJURY

In order to meet immunity standards, the following cable lengths should not be exceeded without additional
protection or electrical considerations:

DC 24V in: 22m
DC12 out: 3m
HDMI: 30m
VGA: 30m
S-Video: 30m
Audio In: 30m

Note that cable length may depend on other factors such as other equipment or cable construction. This
restriction is purely in respect of interference rejection, and that attaching long cables to these ports may act as
antennae for high levels of interference which may affect performance of the product.

Table of Contents

Functional specification ............................................................................................ 1

Power supply ................................................................................................ ............. 1

Video Characteristics ................................................................................................ 1

VGA Input ................................................................................................................... 1

Controls:Back Push Buttons .................................................................................... 1

HDMI Input .................................................................................................................. 1

Audio Input ................................................................................................................. 1

Environmental ............................................................................................................ 1

EDID ............................................................................................................................ 1

Controls and indicators ............................................................................................ 2

RemoteControl…………… ……………………………………………………………….3

OSD Menu .................................................................................................................. 3

Hot Key ....................................................................................................................... 4

PC Mode ..................................................................................................................... 5

Video Mode .............................................................................................................. 13

Camera OSD Menu .................................................................................................. 19

Multi Media Player Menu ......................................................................................... 21

Regulatory Agency .................................................................................................. 35

Safety Approvals ..................................................................................................... 35

EMI/EMS Emission Approvals ................................................................................ 35

Reliability .................................................................................................................. 35

Mechanical ............................................................................................................... 36

Cabinet ..................................................................................................................... 36

Dimensions .............................................................................................................. 36

Memory Card Installation & Camera Setup ........................................................... 37

VESA Mounting ........................................................................................................ 38

Scope

This specification is used to define the performance of PVM19CAM (LED Backlit monitors. This system supports
both video input and PC inputs as well as built-in Camera video. In video input mode, the system can

automatically detect PAL or NTSC signals. In PC mode, this system can support up to 1280 x 1204 VESA
standard.

This system provides frame buffer style de-interlace mechanism and 3D comb filter
to implement the high quality video pictures. The user friendly OSD menu is also
provided to make this system easy to operate.

Functional Specifications

Power Supply

Monitor Power Requirements:

Voltage: 12Vdc or 24Vdc
Current: 4 A max (if 12Vdc) or 2A max (if 24Vdc)

Use only a PSU rated at 12dc, with a minimum current rating of 4A; or 24Vdc, with a minimum current rating of 2A

Video Characteristics

Composite Video (CVBS): 1.0Vp-p (0.5 – 1.5Vpp), Automatic switching from 75 unbalanced termination to Hi-Z

with loop-through operation.

Composite Video (Camera output): 1.0Vp-p (0.5 – 1.5Vpp), loop-through camera signal.

VGA Input

Analog RGB: 0.707Vrms.
Support VESA Standard Timing

HDMI Input

HDMI 1.3 Compatible Interface
HDMI Timing Modes
480i / 480p
576i / 576p
720p
1080i / 1080p

Audio Input

Signal Level: 1.0Vrms

Environmental

 Temperature:
Operating: 00C to +400C
Storage: -200C to +600C
 Humidity:
Operating: 10% to 85% (non-condensing)
Storage: 10% to 95% (non-condensing)

EDID

This series of displays support EDID.

1

Connectors

Power

PC

Video

A – DC 12V or 24V IN connector

C – HDMI

E - S-VIDEO (Y/C) IN: Mini-DIN 4 pins x1

B – DC12V OUT, DC Jack

D – VGA

F – CAMERA OUT: BNC x1

5.5 Ø / 2.5 Ø, Max. 350mA

G/H – CVBS: BNC OUT x1, BNC IN x1

I –AUDIO IN: Stereo Phone Jack x1

J – SD CARD SLOT

A B C D E F G H I

J

Controls and Indicators

2

Remote Control

Monitor Functions

Multi Media Player Functions

DVR Functions
(Option)

Notes:

The remote control requires 2xAAA batteries. Ensure batteries are inserted in the correct polarity according

to the + and – symbols in the battery compartment.

To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote

control handset for an extended period of time.

Batteries should last more than 2 years with normal use.

3

Hot key

VOLUME：Press - / + buttons to adjust the volume.

POWER key for 6 sec to enable this function.

KEY UN-LOCK：Press CHANNEL + MENU + POWER key for 6 sec to disable this function.

RUNNING HOURS：Press MENU + POWER key for 6 sec to display this information.

OSD Menu

KEY LOCK：Press CHANNEL + MENU +

4

PC mode

Main Adjust
Color Adjust
Image Adjust
Information
PIP/PAP Setting
Language
Setup Menu
Recall
Audio Control
Exit

Press - /+ buttons to select an icon, then press MENU button to confirm the selection.

5

MAIN ADJUST

1. Press - / + buttons to select an icon

2. Press MENU button to confirm the selection.

3. Press - / + buttons to adjust the value

4. Press MENU button to return

BRIGHTNESS Adjust the brightness value

CONTRAST Adjust the contrast value

VOLUME Adjust the volume

EXIT Press MENU button to return to the main menu

COLOR ADJUST

Set the color temperature of the LCD monitor for the CIE coordinate 9300˚k, 6500˚k or USER MODE

6

1. Press - / + buttons to select an icon

2. Press MENU button to confirm the selection.

3. Press - / + buttons to adjust the value

4. Press MENU button to return.

RED Adjust the RED value.

GREEN Adjust the GREEN value

BLUE Adjust the BLUE value for

EXIT Press MENU button to return to the main menu

IMAGE ADJUST (VGA ONLY)

1. Press - / + buttons to select an icon

2. Press MENU button to confirm the selection.

3. Press - / + buttons to adjust the value

4. Press MENU button to return

AUTO ADJUST Press MENU buttons to auto adjust Image Settings

H. POSITION Adjust the horizontal position value

V. POSITION Adjust the vertical position value

PHASE Adjust the phase value

CLOCK Adjust the clock value

EXIT Press MENU button to return to the main menu

7

INFORMATION

Press MENU button to get the VGA timing information

PIP/PAP SETTING

Press MENU button to enter the sub-menu

1. Press - / + buttons to select an icon

2. Press MENU button to select adjust item

3. Press - / + buttons to adjust the value

4. Press MENU button to return

8