Vista 20SE User Manual
VISTA-20
®
Previous Menu
Features Q.E.D. programming for quick
enrollment of devices.
2-PARTITIONED
SECURITY SYSTEM
PROGRAMMING
FORM
SE
Principal changes between the VISTA-20SE and
the former VISTA-20 are indicated by margin lines.
VISTA-20PRV4 8/97 (See Instructions N7526V4)
Local programming requires the use of a 2-line Alpha keypad connected to
partition 1 keypad terminals on the control.
NOTE: For UL installations, the system may be configured as a single partition only.
Field Function Programmed Values [ ] = Default Value
SYSTEM SETUP (*20–*29)
*
20 INSTALLER CODE | | | [4 1 1 2]
Enter 4 digits, 0–9
*
21 QUICK ARM ENABLE [0]
Part. 1†Part.2
*
22 RF SYSTEM [0]
†
0 = no; 1 = yes
0 = none; 1 = 5800 (5881/5882)
*
23 FORCED BYPASS [0] [0]
Part. 1†Part. 2† 0 = none; 1 = bypass open zones
“0”. for UL installations.
*
24 RF HOUSE ID CODE | [0][0]
00 = disable all wireless keypad usage; 01–31 = using 5827
keypad; Partition 2 RF House ID = Partition 1 House ID +1
*
25 WIRED ZONE EXPANSION † [0]
0 = none; 1 = 4219; 2 = 4229; 3 = 4204
*
26 CHIME BY ZONE † [0]
0 = no; 1 = yes (program zones to chime on zone list 3)
*
27
X–10 HOUSE CODE
[0]
0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I, 9 =
J, #10 = K, #11 = L, #12 = M, #13 = N, #14 = O, #15 = P
*
28 PHONE MODULE ACCESS CODE | [00]
(Partition 1 only) 1st digit: enter 1–9; 2nd digit: enter # + 11 for "
", or # + 12 for "#". Entering 0 for either digit disables code.
*
29 OUTPUT TO LONG RANGE RADIO [0]
0 = disable; enable = Trouble code 1–9, B (# +11), C (# + 12), D
(# + 13), E (# + 14), or F (# + 15). The 2nd digit of Trouble Dialer
Report is automatically entered from field * 60. “0” for UL
installations.
*
ZONE SOUNDS AND TIMING (*31–*39)
*
31 SINGLE ALARM SOUNDING/ZONE † [0]
1 = yes; 0 = no; “0” for UL installations.
*
32 FIRE SOUNDER TIMEOUT † [0]
0 = timeout; 1 = no timeout
*
33 ALARM BELL TIMEOUT † [1]
0 = none; 1=4 min; 2=8 min; 3=12 min; 4 = 16 min; “1” (4 min.)
minimum for UL.
*
34 EXIT DELAY | | [70] [70]
†
Part. 1
*
35 ENTRY DELAY 1 (zone type 01) | | [30] [30]
Part. 1 †Part. 2
Part. 2
†
00-99 = exit delay time for each partition
†
00-99 = entry delay 1 time for each
partition; 20 seconds max. for UL installations
†
Entry of a number other than one specified will give unpredictable results.
– 2 –
*
36 ENTRY DELAY 2 (zone type 02) | | [60] [60]
Part. 1 †Part. 2
†
00-99 = entry delay 2 time for each
partition; 50 seconds max. for UL installations
*
37 AUDIBLE EXIT WARNING [1] [1]
Part. 1 †Part. 2
*
38 CONFIRMATION OF ARMING DING [0] [0]
†
0 = no; 1 = yes
Part. 1 †Part. 2 †
0 = no; 1 = yes (wired keypads and RF); 2 = yes, RF only
*
39 POWER UP IN PREVIOUS STATE
† [1]
0 = no; 1 = yes; “1” for UL installations
DIALER PROGRAMMING (*40–*53)
In fields *40, *41, *42, enter up to the number of digits shown. Do not fill unused spaces. Enter 0–9; #+11 for '*';
#+12 for '#'; #+13 for a pause.
*
40 PABX ACCESS CODE | | | | |
Enter 6 digits. If fewer than 6 digits are entered, exit by
pressing * (and press 41, if entering next field). To clear entries
from field, press *40* .
*
41 PRIMARY PHONE No. | | | | | | | | | | | | | | |
Enter up to 16 digits; Do not fill unused spaces. If fewer than 16
digits entered, exit by pressing * (and press 42, if entering next
field). To clear entries from field, press * 41* .
*
42 SECONDARY PHONE No. | | | | | | | | | | | | | | |
Enter up to 16 digits; Do not fill unused spaces. If fewer than 16
digits entered, exit by pressing * (and press 43, if entering next
field). To clear entries from field, press *42* .
*
43 PRIMARY SUBS ACCT # (Part. 1) | | |
For fields *43 - *46:
Enter 0–9; #+11 for B; #+12 for C; #+13
*
44 SECONDARY SUBS ACCT # (Part. 1) | | |
*
45 PRIMARY SUBS ACCT # (Part. 2) | | |
*
46 SECONDARY SUB S ACCT # ( Part . 2) | | |
NOTE: If using the paging feature, do not enter a
leading 0 in the subscriber account number, and do
not use digits A-F anywhere in the number. Some
paging systems provide voice mail capability, which
for D; #+14 for E; [#+15 for F]. Enter * as
4th digit, if 3+1 dialer reporting is to be
used. If only 3 digits used, exit by pressing
*
(and press next field).
To clear entries from field, press *43
,*44*, *45*, or *46* .Examples:
For Acct. 1234, enter: 1 | 2 | 3 | 4
For Acct. B234 , enter: #+11| 2 | 3 | 4
For Acct. 123, enter: 1 | 2 | 3 | *
is activated by a leading 0 in the message.
*
47 PHONE SYSTEM SELECT † [1]
If Cent. Sta.
Dial; if Cent. Sta.
IS NOT
IS on
on a WATS line: 0 = Pulse Dial; 1 = Tone
a WATS line: 2 = Pulse Dial ; 3 = Tone
Dial.
*
48 REPORT FORMAT [7] [0]
Primary Secondary
0 = 3+1, 4+1 ADEMCO L/S STANDARD
1 = 3+1, 4+1 RADIONICS STANDARD
2 = 4+2 ADEMCO L/S STANDARD
3 = 4+2 RADIONICS STANDARD
6 or undefined = 4+2 ADEMCO EXPRESS
7 = ADEMCO CONTACT ID REPORTING
8 = 3+1, 4+1 ADEMCO L/S EXPANDED
9 = 3+1, 4+1 RADIONICS EXPANDED
*
†
Entry of a number other than one specified will give unpredictable results.
– 3 –
Loading...