Visonic WT-104, SRN-2000W/PCN Installation Instructions Manual

DE2051 1

WT

WTWT

WT-104

-104-104

-104

4-Channel Hand-Held Wireless Transmitter

Installation Instructions

1111. INTRODUCTION

. INTRODUCTION. INTRODUCTION

. INTRODUCTION

The WT-104 is a miniature, 4-channel hand-held wireless trans­mitter, designed to operate with Visonic Ltd. wireless receivers of
the WR-200 and WR-300 series.

Transmission is activated by pressing any one of the 4 recessed
buttons on the unit. Transmitted data consists of a system code
(see Para. 3.2 below) and one of four different channel codes that
activates the corresponding output of the target receiver.

The transmitter is powered by a 12 volt alkaline battery. An LED
lights during transmission, indicating the battery voltage condition. If
the LED does not light during transmission, the battery must be
replaced immediately.

All WT-104 units are supplied with a key-holder installed. A neck
chain is also included in the package, to permit the unit to be
worn as a pendant transmitter.

Figure 1. WT-104 with Front Cover Removed

2222. SPECIFICATIONS

. SPECIFICATIONS. SPECIFICATIONS

. SPECIFICATIONS

Frequency (MHz): 315, 404, 418, 433.92 or other frequencies
per local requirements.

Encoding: 8-bit digital word, 256 combinations, pulse width
modulation.

Power Supply: 12-volt alkaline battery (Duracell MN-21, Golden
Power GP-23A, or equivalent).

Attention: Transmitter characteristics may be affected by battery
condition.

Transmit Indicator: Lights if the battery voltage exceeds 8 VDC.

Operating Temperature: 0° to 49°C (32° to 120°F).

Dimensions: 35 x 80 x 18 mm (1-3/8 x 3-1/8 x 3/4 in).

Weight: 28 g (1 oz).

Color: White

Standards: Designed to meet FCC Part 15; meets MPT 1340,

ETS 300 220, ETS 300 339 and ETS 300 683 (CE approved).

3333. INSTALLATION

. INSTALLATION. INSTALLATION

. INSTALLATION

3.1 Battery Installation

A. Open the case by removing the screw from the back cover.

B. Insert the 12-volt alkaline battery (Duracell MN-21 or Golden

Power GP-23A or equivalent) between the battery clips, so
that the (+) and (–) markings on the battery are in the same
direction as the markings on the P.C. board (close to each
battery clip - see Figure 1). Check that the battery is held
securely by the battery clips.

C. Gently press one of the pushbutton switches and verify that

the LED lights, indicating good battery condition.

3.2 Coding

A. All WT-104 units have an

8-key DIP switch block
(marked 1 to 8). Each switch
may be set to ON or OFF
position, to create a unique
digital system code - see
Figures 1 and 2.

Figure 2. Code Selector

B. Use a ball point pen to set each of the switches to match the

code setting of the companion receiver.

CAUTION: The code combination 2, 4, 5, 6, 7 ON / 1, 3, 8
OFF is a factory test code which must not be used. Also avoid
codes which are often used: all keys ON, all keys OFF or
alternating ON/OFF settings.

C. Carefully position the front cover hole over the LED. Secure

the front cover with the screw (through the back cover).

3.3 Testing

A. Carefully position the front cover hole over the LED. Secure

the front cover with a screw (through the back cover).

B. Stand 10 feet away from the receiver and press the Channel 1

(Gray) button on the WT-104 .

Note: Verify that the transmission indicator lights, indicating
good battery condition.

C. Observe that the receiver LED lights, indicating detection of

the transmitted RF signal.

D. Verify activation of the CHANNEL 1 relay at the receiver.

E. Repeat steps B through D for channels 2, 3 and 4.

F. Operate the transmitter from various locations within the

protected area to determine "dead" spots, where transmission
is affected by structural materials etc.

3.4 Neck Chain Installation

A. Remove the key-ring leaving the triangle installed on the

bottom of the WT-104.

B. Open the chain and slip it through the triangle.

2 DE2051

4444.

. .

. MISCELLANEOUS COMMENTS

MISCELLANEOUS COMMENTSMISCELLANEOUS COMMENTS

MISCELLANEOUS COMMENTS

4.1 Product Limitations

Our wireless systems are very reliable and are tested to high
standards. However, due to their low transmitting power (required
by FCC regulations) there are some limitations to be considered:

A. Receivers may be blocked by radio signals occurring on or

near their operating frequencies, regardless of the code
selected.

B. A receiver can only respond to one transmitted signal at a

time.

C. Wireless equipment should be tested regularly (at least once

a week) to determine if there are sources of interference and
to protect against faults.

4.2 Compliance with Standards

WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

The 315 MHz model of the WT-104 complies with Part 15 of the
FCC Rules and RSS-210 of Industry and Science Canada.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference that may be received, including
interference that may cause undesired operation.

The 418 & 433.92 models of the WT-104 comply with the
European Council Directive EMC 89/336/EEC & 92/31/EEC and
bear the CE mark and certification.

WARRANTY

WARRANTYWARRANTY

WARRANTY

Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its
products hereinafter referred to as "the Product" or "Products" to be in conformance with
its own plans and specifications and to be free of defects in materials and workmanship
under normal use and service for a period of twelve months from the date of shipment by
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty
period, at its option, to repair or replace the product or any part thereof. The Manufacturer
shall not be responsible for dismantling and/or reinstallation charges. To exercise the
warranty the product must be returned to the Manufacturer freight prepaid and insured.

This warranty does not apply in the following cases: improper installation, misuse,
failure to follow installation and operating instructions, alteration, abuse, accident or
tampering, and repair by anyone other than the Manufacturer.

This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express or implied, including any warranty of
merchantability or fitness for a particular purpose, or otherwise. In no case shall the
Manufacturer be liable to anyone for any consequential or incidental damages for breach
of this warranty or any other warranties whatsoever, as aforesaid.

This warranty shall not be modified, varied or extended, and the Manufacturer does not
authorize any person to act on its behalf in the modification, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, including batteries, shall be
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, including batteries, used in conjunction with the Products.

The Manufacturer does not represent that its Product may not be compromised and/or
circumvented, or that the Product will prevent any death, personal and/or bodily injury
and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. User understands that a
properly installed and maintained alarm may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no death, personal damage and/or damage to
property as a result.

The Manufacturer shall have no liability for any death, personal and/or bodily injury
and/or damage to property or other loss whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, the
Manufacturer's maximum liability shall not in any case exceed the purchase price of the
Product, which shall be fixed as liquidated damages and not as a penalty, and shall be
the complete and exclusive remedy against the Manufacturer.

Warning: The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environmental conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user
is advised to take all necessary precautions for his/her safety and the protection of his/her
property.

6/91

VISONIC LTD. (ISRAEL):

P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: [phone], FAX: [phone]

VISONIC INC. (U.S.A.):

10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: [phone] FAX: [phone]

VISONIC LTD. (UK):

FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: [phone] FAX: [phone]Internet

INTERNET:

www.visonic.com

VISONIC LTD. 1999 WT-104 D-2051-0 NEW: DE2051- (REV. 3, 4/99)