Visonic TOWER-20 PG2 Installation Instructions Manual

Download

TOWER-20 PG2

PowerG, Outdoor Mirror PIR Motion Detector with Anti-masking and Built-In Camera

Installation Instructions

1. INTRODUCTION

The TOWER 20 AM PG2 is a 2-way, wireless outdoor digital mirror PIR detector which includes the following features:

l Patented 8 independent quad PIR detectors (Octa-QUAD

processing for each of the 8 PIR detectors, as well as central motion pr ocessingthat distinguishes between moving intruders and trees and bushes in motion.

l Advanced Obsidian Black Mirror l Optimum performance even in poor weather conditions such as snow, rain, dust, wind and direct sunlight l Tamper protection prevents opening and removal fr om wall l PowerG two-way Frequency Hopping Spread Spectrum FHSS-TDMA technology - provides robustness and reliabilitythat is closer than ever to

optics(patent pending).

wired systems

l Built-in link quality indicators enable installer to checksignalquality without physicallyapproaching the control

panel, thus making installation faster and easier.

l Robust housing with r ecessed window. l Smart anti masking distinguishes between masking spray and rain. l Alarm LED is visible in sunlight. l Automatic termination of walk-test after 15 minutes. l Microprocessor-controlled temperature compensation. l Immunity to pets weighing up to 18 Kg (40lb), not pet alley– see Table 1 l Built-in swivel bracket

) operating in true Quad configuration ( patented) with true motion recognition (TMR)

Figure 1.

General View

2. INSTALLATION

2.1. Installation

A. Bracket installation (see Figure 2). Fix the bracket firmly on a stable wall or pillar. The orientation of the fixed bracket must be as parallel as possible

to the surveyed ground surface.

B. Adjust the detector's horizontal and vertical angles(see Figure 3), according to the surveyed ground surface. The vertical angle indicator position

for various installation height and coverage distance combinations is detailed in Table 1 (the information refers to a relatively flat surveyed area. Verify the correct installation by walk-test).

C. Fasten the detector to the bracket (see Figure 2 step 4).

Table 1 - Vertical Adjustment Reference

Mounting Heigh t Coverage Distance

2m / 6.7ft 4m / 13ft 6m / 20ft 8m / 26ft 10m / 33 ft 12m / 39 ft

3.0m / 10 ft - 1 2 2 3 3

2.5m / 8 ft 1 1 2 3 4 4

2.0m / 7 ft 1 2 3 4 5 5

1.5m / 5 ft 2 3 4 5 5 -

Note: The grayed-in cellsin T able 1 are the installation alternatives recommended for further reducing false alarms from pets.

D-304046 TOWER-20 PG2 Installation Instructions 1

Corr ect Installation

Incorrect Installation

A. Mark drilling point B. For wall tamper C. Drill

D. Fasten

E. Three long screws F. Two short screws

Note: The 2 screw holes enable adjustment of the bracket on the wall, if needed, following the walk test.

Figure 2 - Installation

HORIZONT AL ADJUSTMENT (-45° to +45°)

VERTICAL ADJUSTMENT ( 0° to -10° in 2.5° clicks / steps)

D-304046 TOWER-20 PG2 Installation Instructions 2

COVER CLOSURE

1. Release locking 2. Adjust 3. Lock 4. Release locking 5. Adjust

6. Lock 7. Turn cover and push slider 8 & 9. Put back cover 10. Secure with screw

A. Vertical angle steps

Figure 3 - Adjustment and Cover Closure

2.2. Battery Insertion

It is recommended to perform the first batteries insertion on a flat surface (see F igure 4). After battery insertion, the LED will flash for 60 seconds and then the detector will enter a 15 minutes' local diagnostic mode.

A. Tamper switch B. Press firmlyto release the bracket C. 3 screws

Figure 4 – Battery Insertion

2.3. Enrollment

Refer to the PowerMaster control panel's Installer Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu. Ageneral description of the procedure is provided in the following flow chart.

Step 1 Step 2 Step 3 Step 4

Enter the Installer menu and select

“02:ZONES/DEVICES”

02:ZONES/DEVICES

Step 5 Step 6 Step 7

Configure Location, Zone Type &

Chime parameters

D-304046 TOWER-20 PG2 Installation Instructions 3

Select "ADD NEW DEVICE"

See Note 1

ADD NEW DEVICES

MODIFY DEVICES

Enter PARTITIONS.

See Note 2

Enroll the device (see Figure 5) or

enter the device ID

ENROLL NOW or

ENTR ID:XXX-XXXX

Assign partitions to the detector by

pressing the ,

and/or buttons on the

Select a detector number for the

new flood detector

Z14:Motion Sens ID No. 130-XXXX

panel

Z14.LOCATION Z14.ZONE TYPE Z14.SET CHIME

ðmeans scroll wwand select OK.

Notes:

[1] If the detector is already enrolled you can configure the detector parameters and assign partitions via the “Modify Devices” option – see Step 2. [2] PARTITIONS willappear only if PARTITIONING was previouslyenabled in a panel that supports the Partitioning feature (for further details, see "Partitioning" in the PowerMaster Installer Guide).

Z14.PARTIT IONS

Z14:P1n-- P2....P3n

2.4. Configuring the Detector Parameters

Enter the DEVICE SETTINGS menu and follow the configuration instructions for the TOWER 20 AM PG2 PIR detector as described below.

Option Con fig uration Instructions

ALARM LED Define whether or not to activate the alarm LED indication.

Optional settings: ON (default) and OFF.

PIR SENSITIVITY

DISARM ACTIVITY

OUTDOOR ANTI-M

ALARM Hou rs

Define if the detector operates at regular or high PIR sensitivity, or that at leastone detection zone must be crossed before an alarm is triggered (One Region).

Optional settings: LOW (default), HIGH and One Region.

Note: For EN compliance, the detector should be set to "One Region".

Define whether or not to set the activitytime during Disarm mode.

Optional settings: NOT Active (default), YES – no delay, YES + 5s delay, YES + 15s delay, YES + 30s delay, YES + 1m delay, YES + 2m delay, YES + 5m delay, YES + 10m delay, YES + 20m delay and YES+60m delay.

Enable or disable the outdoor anti-masking featur e.

Optional settings: Disabled (default) and Enabled.

Define whether motion alarms are always enabled or onlywhen dark (at night).

Optional settings: Day and Night (default) and Night only.

2.5. Local Diagnostic Test

A. Set the detector in localdiagnosticmode, as follows:

Open the detector’s bottom cover (see "Figure 4 – Battery Insertion" on the previous page, steps 1 - 3) and then press and release the tamper switch (see "Figure 5. TOWER 20 AM PG2 " on the next page). The LED will flash for 60 seconds and then the detector will enter into 15 minutes' localdiagnosticmode.

Note: Note: The detector automatically enters into 15 minutes' localdiagnosticmode after batter y installation or Tamper switch recovery.

B. Adjust the detector in the horizontalplane to cover the required protected area.

Walk into the detectors’ field of view. Adjust the verticalplane to receive the maximum number of detections when crossingthe entire 90° pattern.

Verify that the LED blinks each time your motion isdetected, as you cross one Quad PIR. Then verify that the LED lights steadily for 2 secondsas you cross the next adjacent Quad PIR. After alarm indication, the LED blinks three times and provides the received signal strength indication (see Table 2).

Table 2 – Received Signal Strength Ind ication

LED respo nse Reception

Green LED links Strong

Orange LED blinks Good

Red LED blinks Poor

No blinks No communication

Important! Reliable reception must be assured. Therefore, "poor " signal strength isnot acceptable. If you receive a "poor" signal fr om the detector, relocate it and re-test untila "Good" or "Strong" signal strength isreceived. Note: For detailed Diagnostics Test instructions r efer to the control panel Installer's Guide

The LED blinking, described above, isoperative only in Local diagnostic mode. Upon each fulldetection (LED lights steadilyfor 2 seconds), the control panel receivesthe alarm. If required, perform the detector's horizontal / vertical adjustments (see section 2.1 and Figure 3).

Important! Instruct the user to perform a walk test at least once a week, to verify proper oper ation of the detector.

D. Place a piece of cardboard on the detector’s front side to deliberately mask the opticalwindow. Verify that after 2 minutes, the yellow LED lights

continuously (see Table 3 below) and the alarm control panel receivesthe masking alarm.

E. Remove the masking from the detector’s front side. Verify that the LED turns off

Table 3 - LED operation

LED Indications Event

Red LED blinks Stabilization (warm-up 60 sec)

Red LED ON 0.2 sec. Tamper open / close

Red LED blinkstwice One quad PIR detection in diagnosticmode

Red LED on 2 sec. Intruder alarm

D-304046 TOWER-20 PG2 Installation Instructions 4

Yellow LED on AM detection – diagnostic mode

Yellow LED blinks slowly (0.2 sec. ON, 30 sec. OFF) AM detection – Normal mode

Note: After detection, the detector disablesitself to save battery power. It reverts to the ready state if there is no subsequent detection thr oughout the following 2-minute period.

A. LED B. Enroll button C. Tamper switch

Figure 5. TOWER 20 AM PG2

3. COMPLIANCE WITH STANDARDS

Europe: EN 300220, EN 301489, EN 60950-1, EN 60950-22, EN 50130-4, EN 50130-5, EN 50131-2-2, EN 50131-5-3, EN 50131-6.

Hereby, Visonic Ltd. declares that the radio equipment type TOWER-20 PG2 isin compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity isavailable at the following internet address: http://www.visonic.com/download-center.

Certified by Norwegian accredited certification body Applica Test & Certification AS in accordance with EN 50131-2-2, EN 50131-5-3, EN 50131-6, EN 50130-4, and EN 50130-5. EN 50131-1 Security Grade: According to EN 50131-1 this equipment can be applied in installed systems up to and including Security Grade 2.

EN 50131-1 Environmental Class: Class IV

UK: T his product is suitable for use in systemsinstalled to conform to PD6662:2010 at Grade 2 and environmental class 4. DD243 and

BS8243

USA: FCC- CFR 47 Part 15,

Canada: IC-RSS 210

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. T hese limits ar e designed to provide reasonable protection against harmful interference in residentialinstallations. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to r adio and television reception.

However, there is no guarantee that interfer ence willnot occur in a particular installation. If this device does cause such interfer ence, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures: – Re-orient or re-locate the receiving antenna. – Increase the distance between the device and the receiver. – Connect the device to an outlet on a circuit different from the one that supplies power to the receiver. – Consult the dealer or an experienced radio/TV technician.

FCC Complian ce Statement

This device has been tested and found to comply with the limits for a Class B digital device, pur suant to Part 15 of the FCC Rules. These limits ar e designed to provide reasonable protection against harmful interference in residentialinstallations. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio and television reception.

l Re-or ient or re- locate the receiving antenna. l Increase the distance between the device and the receiver. l Connect the deviceto an outlet on a circuit different from the one that supplies power to the receiver. l Consult the dealer or an experienced radio/TV technician.

Warning! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with FCC Rules Part 15 and with Industry Canada licence- exempt RSS standard (s). Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appar eils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareilne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.

D-304046 TOWER-20 PG2 Installation Instructions 5

W.E.E.E. Product Recycling Declaration

For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as i dentifiedby your supplier. This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment.

4. APPENDIX: SPECIFICATIONS

OPTICAL Black Mirror Max. Coverage Up to 12 m (40 ft) / 90° Detector Techn ology 8 independent quad PIR detectors operating in true Quad configuration

A. Top view

B. Side view of each detector

Figure 6. Coverage Pattern

Pet Immunity Up to 18 Kg (40 lb) ELECTRICAL Input Power Two 3V CR123A Lithium batteries

Batt ery Life (for typical use) 3 years Low Battery Threshold 4.0 V WIRELESS Frequency Band (MHz) Europe and rest of world: 433-434, 868-869 USA:912-919 Maximum Tx Power 10 dBm @ 433 MHz, 14 dBm @ 868 Mhz Communication Protocol PowerG Tamper Alert Reported when a tamper event occurs and in any subsequent message, until the tamper switch is

MOUNTING Mounting T ype Wall mounting Mounting Heigh t 1.5 – 3.0 m (5 – 10 ft). Horizon tal Adjustment -45° to +45°, in 5° steps Vertical Adjustment 0° to -10°, in 2.5° steps ENVIRONMENTAL Operating Temperatures -35°C to 60°C (- 31°F to 140°F) Storage Temperatures -35°C to 60°C (-31°F to 140°F) Humidity 95% max. White L ight Immunity Above 25000 lux PHYSICAL Size (H x L x W) 157 x 147 x 124 mm (6-3/16 x 5-13/16 x 4-7/8”) Weight (with battery) 600 g (21 oz). Colo r White or gray PATENT S U.S. Patents 7250605 l 6818881 l 5693943 (other patents pending)

Caut ion! Riskof explosion if battery is replaced by an incorrect type. Dispose of used battery according to the manufacturer's instructions.

restored

WARRANTY

Visonic Limited (the “Manufacturer") warrants this product only(the "Product") to the originalpurchaser only (the “Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve (12) months from the date of shipment by the Manufacturer.

This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated under conditions of normal use in accordance with the Manufacturers recommended installation and operation instructions. Products which have become defective for any other reason, according to the Manufacturers discretion, such as improper installation, failure to follow recommended installation and operational instructions, neglect, willfuldamage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty.

D-304046 TOWER-20 PG2 Installation Instructions 6

There is absolutely no warranty on software, and allsoftware products are sold as a user license under the terms of the software license agreement included with such Product."

The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product will prevent any death and/or personal injury and/or damage to proper ty resulting from burglary, robbery, fire or otherwise, or that the Product willin allcases provide adequate warning or pr otection. The Product, properly installed and maintained, only reduces the riskof such events without warning and it is not a guarantee or insurance that such events willnot occur.

Con dit ions to Vo id Warrant y: This warranty appliesonly to defects in parts and workmanship relating to nor mal use of the Products. It does not cover:

* damage incurred in shipping or handling;

* damage caused by disaster such as fire, flood, wind, earthquake or lightning;

* damage due to causesbeyond the control of the Seller such as excessive voltage, mechanicalshockor water damage;

* damage caused by unauthorized attachment, alterations, modifications or foreign objectsbeing used with or in conjunction with the Products;

* damage caused by peripherals (unlesssuch peripherals were supplied by the Seller;

* defects caused by failure to provide a suitable installation environment for the products;

* damage caused by use of the Products for purposes other than those for which they were designed;

* damage from improper maintenance;

* damage arising out of any other abuse, mishandling or improper application of the Products.

Items Not Covered by Warranty: In addition to the items which void the Warranty, the following items shallnot be covered by War ranty: (i) freight cost to the repair centre; (ii) customs fees, taxes,or VAT that may be due; (iii) Products which are not identified with the Seller's product label and lot number or serial number; (iv) Products disassembled or repaired in such a manner as to adversely affect per formance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at the Seller's option.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES, WHETHER WRITT EN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS F OR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANT Y OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID.

THE MANUFACT URER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR PUNIT IVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECT LY OR INDIRECTLY ARISING FROM PURCHASER’S USE OR INABILITY TO USE T HE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

THE MANUFACT URER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENT AL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION. HOWEVER, IF THE MANUFACTURER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY, THE MANUFACT URER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT INVOLVED, WHICH SHALL BE FIXED AS LIQUIDATED DAMAGES AND NOT AS A PENALTY, AND SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST THE MANUFACTURER. SOME JURISDICT IONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THESE LIMITATIONS MAY NOT APPLY UNDER CERTAIN CIRCUMSTANCES.

When accepting the delivery of the Product, the Pur chaser agrees to the said conditions of sale and warranty and he recognizeshaving been informed of.

The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any telecommunication or electronic equipment or any programs.

The Manufacturers obligationsunder this Warranty ar e limited solelyto repair and/or replace at the Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or replacement shall not extend the original Warr anty period. The Manufacturer shall not be responsible for dismantling and/or reinstallation costs. To exercise this War ranty the Product must be returned to the Manufacturer freight pre-paid and insured. Allfreight and insurance costsare the responsibility of the Purchaser and are not included in this Warr anty.

For sales in Israel only:

The Purchaser shall comply with the provisions of the Israeli Consumer Protection Law – 1981("Consumer Protection Law") related regulations, including the Israeli Consumer Protection Regulations (Warranty Sticker), 5772-2012) ("Regulations"), including, without limitation (i) providing its customers with at least the minimum warranty r equired by the Consumer Protection Law, and (ii) ensuring that a warranty certificate and a warranty sticker (as defined in the Regulations) ("Warr anty Sticker") shall be attached to any sold Products and the date of the sale of the Product to the consumer or the end-user shallbe added in a r eadable manner on the Warranty Sticker.

In no event shall the Purchser’s compliance with the Consumer Protection Law and Regulations expand any of the Manufacturer's warranty obligations under this warranty, and the Purchaser shallbe responsible for any warranty that it provideswith respect to the Products which exceeds or is different from this warranty.

This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalf in the modification, variation or extension of this warranty. This warranty shallapply to the Product only. All products, accessories or attachments of other s used in conjunction with the Product, including batteries, shallbe covered solely by their own warranty, if any. The Manufacturer shallnot be liable for any

D-304046 TOWER-20 PG2 Installation Instructions 7

damage or loss whatsoever, whether directly,indirectly,incidentally, consequentiallyor otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of others, including batteries, used in conjunction with the Products. This War ranty is exclusive to the original Purchaser and is not assignable.

This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is contrary to the Law in the state or country were the Product is supplied shall not apply.

Governing Law: T his disclaimer of warranties and limited warranty are governed by the domestic laws of Israel.

Warning

The user must follow the Manufacturer’s installation and operational instructions including testing the Product and its whole system at least once a week and to take all necessary precautions for his/her safety and the protection of his/her property.

* In case of a conflict, contradiction or interpretation between the English version of the warranty and other versions,the English version shallpr evail.

D-304046 TOWER-20 PG2 Installation Instructions 8