Visonic SPD1000 Users Manual

SPD

SPD-1000

SPDSPD

-1000

-1000-1000

Wireless Magnetic Displacement Detector

1111. INTRODUCTION

. INTRODUCTION

. INTRODUCTION. INTRODUCTION

SPD-1000 is a fully supervised wireless detector, designed for
protection of paintings, sculptures and other artwork, in
museums, galleries, churches, private artwork collections, etc.

Figure 1 - Integration of SPD-1000 in an Alarm System

When someone tries to touch or remove the secured object, to
which the detector is attached, an identifiable alarm signal is
transmitted to alert security personnel. Identifiable signals
include: low battery voltage alert, low severity alarm (slight touch)
and high severity alarm (repetitive touch, strong touch or
removal).

2222. SPECIFICATIONS

. SPECIFICATIONS

. SPECIFICATIONS. SPECIFICATIONS

Movement Detection Sensitivity: 0.1 mm
Transmission Frequency (MHz): 315 or 433.92
Compatible Receivers: PowerArt / MCR-308, SpiderAlert

SR-500ER / SCP-532ER / SR-520ER.
Overall Message Length: 36 bits, including 24-bit identification

code, pulse width modulation.

Supervision

(Europe)
Power Source: Two 3V/160 mAh Lithium batteries, GP CR-2025,

or equivalent.

Current Consumption: 8 µA (STBY), 8 mA (transmission)
Battery Life: 5 years under normal installation conditions

Transmission:

Every 60 min. (USA) / 15 min.

Installation Instructions

In addition, the detector periodically sends
supervision signal as a serviceability report.

With PowerArt high level, sensitivity can be
extended.

The detector has 3 modes:
A . “Sleep” - for the detector transport or

long term storage, without causing an
alarm. In this mode the current
consumption is very low.

B . “Installation” - for sensor's spring active

range adjustment and for teaching the
SpiderAlert / PowerArt system the
detector’s identity.

C . “Operation”.

All mode changes and alarms are aurally indicated by an integral
buzzer.

The SPD-1000 has tracking mode (for SpiderAlert only) that
enables to track the secured object's location up to 10 minutes
after its removal (with SpiderAlert receivers deployed within the
site). This option is possible if the detector is attached to the
secured object.

For a large painting, several SPD-1000 units can be used.

Battery Supervision: Automatic transmission of battery condition
data as part of any status report.

Tracking Transmission: Every 30 sec., while the secured object
is being moved from its original place, up to 10 min. after last
movement.

Operating Temperatures: 0°C to 50°C (32°F to 122°F)
Dimensions (HxWxD): 96
Weight (with battery): 34.8 g (1.2 oz)
Color: Housing - white, spring - nickel
Compliance with Standards: FCC part 15, IC:1467102181.

The term "IC" before the certification/registration number only
signifies that the Industry Canada technical specifications were met.

x 28 x 22 mm

(3-13/16 x 1-1/8 x 7/8 in.)

Figure 2

External View

3333. INSTALLATION

. INSTALLATION

. INSTALLATION. INSTALLATION

3.1 Installation Options

Figure 3 - Installation Possibilities

DE3652 1

Figure 4 - Using a Bracket to Attach the Detector

Attention!

Before detector installation:
1 . Remove spring movement prevention sticker (see fig. 5).
2 . Remove protective non-metallic spacer that keeps the

spring in the “sleep” mode (shown in par. 3.7).

3.2 Setting the SMD Switches

Figure 5

Switch
Setting
Method

Table 1 - SMD Switches Functions

Switch Function Pos. Selected Option Default

SW. 1 Sensitivity

& tracking

ON Spider: Tracking enabled

PowerArt: High sensitivity ON

OFF Spider: Tracking disabled

PowerArt: Low Sensitivity

SW. 2 Buzzer ON Enabled ON

OFF Disabled

SW. 3 Supervision ON USA (60 Min.) ON

OFF Europe (15 Min.)

SW. 4 Mode ON SpiderAlert ON

OFF PowerArt or MCR-308

3.3 Preparation for Use

B . Verify that the teaching is successful, according to the

previously mentioned documents.

3.5 Teaching the SpiderAlert System

Teach SpiderAlert system to identify SPD-1000 transmissions:

A . In SpiderAlert software Click File/Transmitters/Museum/Add.
B . Initiate low severity alarm transmission by momentarily

pressing Reset switch (see par. 3.3, step 1).

C . The detector’s ID number will be displayed in the yellow box.
D . Press the “<<” button to move the ID number from the yellow

(temporary) box to the “ID” box.

E . In the Location box, type the secured object's name (i.e.

Mona Liza picture).

F . In Holder Group box, type a desired name for the museum

detectors group for whom the event handling will be identical.

G . Press the button, to display the Museum Group screen.
H . Select the appropriate museum detectors group.

...

I . Press Edit button, define (for the operator) the handling

description for every detector’s event and press OK.

3.6 Operation

SPD-1000 function is based on magnetic field changes as a
result of the secured object movements. The detector has 2
detection levels - low severity alarm (continuous slight touch) and
high severity alarm (strong touch or removal).

Once stabilized, the detector checks its position continuously.
Upon a movement detection, the detector sends alarm as follows:

Note: After HIGH alarm only, the detector needs 90-second
stabilization period at least, for the next movement detection.

When Low or High level alarm is
transmitted, 2 weak buzzer sounds are
heard, as shown.

3.7 Entering the “Sleep” Mode

Entering Sleep mode (for description, see section 1) is as follows:

3.4 Teaching PowerArt / MCR-308

Teach PowerArt / MCR-308 to identify SPD-1000:
A . Teach PowerArt (see par. 3.2G in PowerArt Prog. Guide) or

MCR-308 (see par. 3.5 in MCR-308 installation instructions).
When instructed to transmit, initiate SPD-1000 low severity
alarm transmission by momentarily pressing the Reset switch
(see illustration 1 in par. 3.3).

Note: According to this signal, the PowerArt automatically learns

to identify high severity alarm, low severity alarm, low battery and
supervision messages. According to this signal the MCR-308
learns to identify low severity alarm only.

To teach the MCR-308 the high severity alarm, create the alarm

after the detector has been stabilized, by strong movement /
removal of the secured object.

VISONETIX LTD. (ISRAEL):
VISONIC SYSTEMS INC. (U.S.A.):
VISONIC LTD. (UK):

VISONETIX LTD. 2001 SPD-1000 DE3652- (REV. 5, 12/2001) Separate warranty statement is enclosed. www.visonetix.com

P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: [phone], FAX: [phone]

10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: [phone] FAX: [phone]

UNIT 1, STRATTON PARK, DUNTON LANE, BIGGLESWADE, BEDS. SG18 8QS. PHONE: [phone] FAX: [phone]

2 DE3652

Compliance with Standards

This device complies with FCC Rules Part 15. Operation is subject to two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference that may be received or that may cause
undesired operation. The user is cautioned that changes or modifications to
the unit, not expressly approved by Visonic Ltd., could void the user's FCC or
other authority to operate the equipment
The 315 MHz is for USA & Canada - not allowed in any EU member state. The

433.92 MHz has no restriction in any EU member state.