Visonic MCT-201WP User Manual

MCT-201, MCT-201 WP

PowerCode Pendant Transmitters

1. INTRODUCTION

The MCT-201 is a miniature pendant UHF transmitter, designed
for use in advanced, high-security alarm and remote control
systems. When enclosed in a waterproof case, this transmitter’s
reference designation is MCT-201WP. Transmission is activated
by depressing the recessed pushbutton at the center of the unit.
When activated, each transmitter sends out a 24-bit ID code and
an alarm code, identifiable by compatible wireless receivers of
the MCR family. Each transmitter's code is randomly selected in
the factory from 16 million possible combinations. The code is
therefore unique and virtually impossible to reproduce.

Operating power is obtained from an internal 12-volt alkaline
battery. An LED lights during transmission, indicating the battery
voltage condition (it lights provided that the battery voltage
exceeds 8 VDC). If the LED does not light during transmission,
the battery must be replaced immediately.

In addition, a transmitter with such a low battery will automatically
send a low battery code with each transmission.

2. SPECIFICATIONS

Frequency (MHz): 315, 433.92, MHz or other frequencies
according to local requirements.

Encoding: 24-bit digital word, over 16 million combinations.
Transmission duration: As long as the button is kept pressed.
Power Supply: 12-volt alkaline battery (Duracell MN-21, Golden

Power GP-23A, or equivalent).

Attention: Transmitter characteristics may be affected by battery
condition.

Dimensions:.

MCT-201: 32 x 53 x 17 mm (1-1/4 x 2-1/8 x 11/16 in.).
MCT-201WP: 40 x 61 x 18 mm (1-9/16 x 2-3/8 x 23/32 in.)

Installation Instructions

Compatible receivers are designed to identify this code and
operate audible or visual alert devices.

Figure 1. MCT-201

All MCT-201 units are supplied with the chain installed, to be
worn around the neck as a pendant transmitter. A key ring is also
included in the package, for use in place of the chain.

Weight: 22 g (0.7 oz).
Operating Temperature: 0° to 49°C (32° to 120°F).
Color: White.
Compliance with Standards: Meets FCC Part 15, MPT1340

and Directive 1999/5/EC

This device complies with the essential requirements and
provisions of Directive 1999/5/EC of the European Parliament and
of the Council of 9 March 1999 on radio and telecommunications
terminal equipment.

3. INSTALLATION

3.1 Battery Installation

A. To open the case, refer to Figure 2. Insert an 1/8 inch

screwdriver blade in the slot at the bottom of the case. Press
the blade inward, applying moderate pressure, and while
pressing, swing the handle slightly down until the covers
partially separate.

Warning! Do not try to open the case by inserting a
screwdriver in places other than the slot. This can damage
the transmitter.

B. Gently complete separation of the front and back covers with

your fingers.

Figure 2. Opening the Case

DE2261 1

C. Insert the 12-volt alkaline battery (Duracell MN-21 or Golden

Power GP-23A or equivalent) between the battery clips, so
that the (+) and (–) markings on the battery are in the same
direction as the markings on the rear half of the case (close to
each battery clip). Check that the battery is held securely by
the battery clips.

D. Gently press the pushbutton switch and verify that the LED

lights, indicating good battery condition.

3.2 Closing the Case

Carefully engage the ridges at the top of the rear cover with the
dents at the top of the front cover. Gently press together the
bottom ends of both covers, until they snap shut.

3.3 Waterproof Version (MCT-201 WP)

The MCT-201WP is a waterproof version of the MCT-201
transmitter. Waterproof units are shipped fully assembled but not
closed, to permit insertion of the battery before final sealing. The
case is made waterproof when its two halves are assembled and
secured together with 4 screws.

To prepare the unit for use, separate the two halves of the case
and lay the unit down on its back as shown in Figure 3.
Insert the cylindrical 12
Observe polarity!

V battery between the battery clips.

Reassemble the two halves of the case and lay the unit face
down. Put a screw in each of the four holes on the back (screws
are supplied in a small bag packed with the unit). Carefully
tighten all 4 screws with phillips screwdriver No. 1.

The unit should now be watertight and ready for use.

Figure 3. Inside View of the MCT-201WP

3.4 Testing

A. Perform the learning procedure as instructed in the particular

receiver’s installation instructions, to enroll the transmitter’s ID
in the receiver’s memory.

B. Stand 3 m (10 ft) away from the receiver and operate the

transmitter.

C. Verify that the transmitter LED lights, indicating good battery

condition.

4. NOTES AND WARNINGS

D. Observe that the receiver LED lights, indicating detection of

the transmitted RF signal.

E. Verify activation of the receiver's corresponding output.
F. Operate the transmitter from various locations within the area

covered by the receiver to determine "dead" locations, where
transmission is obstructed by walls and large objects, or
affected by structural materials.

3.5 Key-Ring Installation

A. Remove the chain by opening and

slipping it through the triangle on
top of the MCT-201.

B. Insert the tip of a long-nose pliers

into the triangle and open it.

C. Remove the triangle.
D. Open the plastic bag which

contains the key-ring kit.

E. Slip the key-ring triangle through

the last link of the key-ring chain
and insert the triangle into the hole
on the upper edge of the MCT-201
(Fig. 4).

F. Using the pliers, close the key-ring

triangle.

Figure 4. Key-ring

Installation

4.1 Product Limitations

Visonic Ltd.’s wireless systems are very reliable and are tested to
high standards. However, due to their low transmitting power
(required by FCC and other regulatory authorities) there are
some limitations to be considered:

A. Receivers may be blocked by radio signals occurring on or

near their operating frequencies.

B. A receiver can only respond to one transmitted signal at a time.
C. Wireless equipment should be tested regularly (at least once

4.2 Frequency Allocations for Wireless
Devices in European (EU) Countries

• 433.92 MHz has no restriction in any EU member state.

• 315 MHz is not allowed in any EU member state

• 868.95 MHz (wide band) is allowed in all EU member states

(except for Belgium).

• 869.2625 MHz (narrow band) is not restricted in any EU
member state.

a week) to determine if there are sources of interference and
to protect against faults.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.

WARRANTY

Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its
products hereinafter referred to as "the Product" or "Products" to be in conformance with
its own plans and specifications and to be free of defects in materials and workmanship
under normal use and service for a period of twelve months from the date of shipment by
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty
period, at its option, to repair or replace the product or any part thereof. The Manufacturer
shall not be responsible for dismantling and/or reinstallation charges. To exercise the
warranty the product must be returned to the Manufacturer freight prepaid and insured.

This warranty does not apply in the following cases: improper installation, misuse,
failure to follow installation and operating instructions, alteration, abuse, accident or
tampering, and repair by anyone other than the Manufacturer.

This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express or implied, including any warranty of
merchantability or fitness for a particular purpose, or otherwise. In no case shall the
Manufacturer be liable to anyone for any consequential or incidental damages for breach
of this warranty or any other warranties whatsoever, as aforesaid.

This warranty shall not be modified, varied or extended, and the Manufacturer does not
authorize any person to act on its behalf in the modification, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, including batteries, shall be
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, including batteries, used in conjunction with the Products.

The Manufacturer does not represent that its Product may not be compromised and/or
circumvented, or that the Product will prevent any death, personal and/or bodily injury
and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. User understands that a
properly installed and maintained alarm may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no death, personal damage and/or damage to
property as a result.

The Manufacturer shall have no liability for any death, personal and/or bodily injury
and/or damage to property or other loss whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, the
Manufacturer's maximum liability shall not in any case exceed the purchase price of the
Product, which shall be fixed as liquidated damages and not as a penalty, and shall be
the complete and exclusive remedy against the Manufacturer.

Warning: The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environmental conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user
is advised to take all necessary precautions for his/her safety and the protection of his/her
property.

6/91

VISONIC LTD. (ISRAEL):
VISONIC INC. (U.S.A.):
VISONIC LTD. (UK):
INTERNET:

VISONIC LTD. 2001 MCT-201, MCT-201WP (12V) DE2261- (REV. 7, 7/01)

www.visonic.com

P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: [phone], FAX: [phone]

10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: [phone] FAX: [phone]

FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: [phone] FAX: [phone]

2 DE2261