Visonic MCT-201, MCT-201 WP Installation Instructions Manual

0&70&7:3

PowerCode Pendant Transmitters

,1752'8&7,21

The MCT-201 is a miniature pendant UHF t ransmitter, designed
for use in advanced, high-security alarm and remote control
systems. W hen enclosed in a waterproof case, this transmitter ’s
reference designation i s MCT-201WP. Trans mission is acti vated
by depressing the rec essed pushbutton at t he center of the uni t.
When activat ed, each transmi tter sends out a 24-bit I D code and
an alarm code, identifiable by compatible wireless receivers of
the MCR family. Each tr ansmitter's c ode is randomly selec ted in
the factory from 16 million possible combinations. The code is
therefore unique and vir tually impossi ble to reproduce.

Operating power is obtained from an internal 12-volt alkaline
battery. An LED lights during transmiss ion, indicating the bat tery
voltage condition (it lights provided that the battery voltage
exceeds 8 VDC). If the LED does not light during t ransmission,
the battery must be replaced immediately.

In addition, a transmitter with s uch a low batt ery will aut omatic ally
send a low battery code with each transmission.

63(&,),&$7,216

Installation Instructions

Compatible receivers are designed to identify this code and
operate audible or vis ual alert devices.

Figure 1. MCT-201

All MCT-201 units are supplied with the chain installed, to be
worn around the neck as a pendant transmi tter . A key r ing is als o
included in the package, for use in place of the chain.

Frequency (MHz): 315, 404, 418, 433.92 or other frequencies
according to local requirements.

Encoding: 24-bit digital word, over 16 million combinat ions.
Transmission durati on: As long as the butt on is kept pressed.
Power Supply: 12-volt alkaline bat tery (Duracell MN-21, Golden

Power GP-23A, or equivalent).

Attention: Transmitt er charact erist ics may be af fected by battery
condition.

Operating Temperatur e: 0° to 49°C (32° to 120°F).

,167$//$7,21

%DWWHU\,QVWDOODWLRQ

A. To open the case, refer to Figure 2. Insert an 1/8 inch

screwdriver blade i n the slot at the bot tom of the case. Press
the blade inward, applying moderate pressure, and while
pressing, swing the handle slightly down until the covers
partially separ ate.

Warning! Do not try to open the case by inserting a
screwdriver in places other than the slot. This can damage
the transmitter.

B. Gently complete separation of the fr ont and back covers wi th

your fingers.

Dimensions:. 32 x 53 x 17 mm (1-1/4 x 2-1/8 x 11/16 in.) .
Weight: 22 g (0.7 oz).
Color: White.
Compliance with Standards:

Meets FCC Part 15, ETS 300-220 and MPT1340.
418 & 433.92 MHz units meet Eur opean Council Directive EMC

89/336/EEC & 92/31/EEC and bear the CE mark and certific ation.

C. Insert the 12-volt alkali ne battery (Duracell MN-21 or Golden

Power GP-23A or equivalent) between the battery clips, so
that the (+) and (–) markings on the battery are i n the same
direction as t he mar ki ngs on the r ear half of t he c as e ( c los e to
each battery clip) . Check that the battery i s held securely by
the battery cli ps.

D. Gently press the pushbutton switch and verify that the LED

lights, indi cating good battery condition.

&ORVLQJWKH&DVH

Carefully engage the ridges at t he top of the rear cover wit h the
dents at the top of the front cover. Gently press together the
bottom ends of both covers, until they snap shut.

Figure 2. Opening the Case

DE2261 1

:DWHUSURRI9HUVLRQ0&7:3

The MCT-201WP is a waterproof version of the MCT-201
transmitter . Wat erproof units are s hipped fully as sembled but not
closed, to permi t insert ion of the batter y before final s ealing. The
case is made waterpr oof when its two hal ves are assembl ed and
secured together with 4 screws.

To prepare the unit for use, separate the tw o halves of the cas e
and lay the unit down on its back as shown in Figur e 3.
Insert the cylindrical 12
Observe polarity!
Reassemble the two halves of the case and lay the unit face

V battery between the battery clips.

down. Put a screw in eac h of the four hol es on the back (sc rews
are supplied in a small bag packed with the unit). Carefully
tighten all 4 screws with phillips screwdriver No. 1.

The unit should now be watert ight and ready for use.

Figure 3. Inside View of the MCT-201WP

7HVWLQJ

A. Stand 3 m (10 ft) away from the receiver and operate the

transmitter.

B. Verify that the transmitter LED lights, indicat ing good battery

condition.

352'8&7/,0,7$7,216

C. Observe that the receiver LED li ghts, indicating detection of

the transmitted RF signal.

D. Verify activation of the receiver's output relay.
E. Operate the transmitter from various locations within the area

covered by the receiver to determine "dead" locations , where
transmission is obstructed by walls and large objects, or
affected by structural materials.

.H\ULQJ,QVWDOODWLRQ

A. Remove the chain by opening and

slipping it through the triangle on
top of the MCT-201.

B. Insert the tip of a long-nose pliers

into the triangle and open it.

C. Remove the triangle.
D. Open the plastic bag which

contains the key-ring kit.

E. Slip the key-ring triangle through

the last link of the keying chain
and install the triangle into the
hole on the top of the MCT-201
(Fig. 4).

F. Us ing the pliers, close the key-ri ng

triangle

Figure 4. Key-ring

Installation

Important Notes: Visonic Ltd.’s wireless systems are very
reliable and are tested to high st andards. However, due to their
low transmitting power (required by FCC and other regulatory
authorities) there are some limitations to be considered:

A. Receivers may be blocked by radio signals occurring on or

near their operating frequencies, regardless of the code
selected.

B. A receiver can only respond to one transmitted signal at a

time.

:$55$17<

:$55$17<

Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its
products hereinafter referred to as "the Product" or "Products" to be in conformance with
its own plans and specifications and to be free of defects in materials and workmanship
under normal use and service for a period of twelve months from the date of shipment by
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty
period, at its option, to repair or replace the product or any part thereof. The Manufacturer
shall not be responsible for dismantling and/or reinstallation charges. To exercise the
warranty the product must be returned to the Manufacturer freight prepaid and insured.

This warranty does not apply in the following cases: improper installation, misuse,
failure to follow installation and operating instructions, alteration, abuse, accident or
tampering, and repair by anyone other than the Manufacturer.

This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express or implied, including any warranty of
merchantability or fitness for a particular purpose, or otherwise. In no case shall the
Manufacturer be liable to anyone for any consequential or incidental damages for breach
of this warranty or any other warranties whatsoever, as aforesaid.

This warranty shall not be modified, varied or extended, and the Manufacturer does not
authorize any person to act on its behalf in the modification, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, including batteries, shall be
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, including batteries, used in conjunction with the Products.

C. Wireless equipment should be t ested regularly (at l east once

a week) to determine if there are s ources of inter ference and
to protect against faults.

WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.

The Manufacturer does not represent that its Product may not be compromised and/or
circumvented, or that the Product will prevent any death, personal and/or bodily injury
and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. User understands that a
properly installed and maintained alarm may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such
will not occur or that there will be no death, personal damage and/or damage to property
as a result.

The Manufacturer shall have no liability for any death, personal and/or bodily injury
and/or damage to property or other loss whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, the
Manufacturer's maximum liability shall not in any case exceed the purchase price of the
Product, which shall be fixed as liquidated damages and not as a penalty, and shall be the
complete and exclusive remedy against the Manufacturer.

Warning: The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environmental conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user
is advised to take all necessary precautions for his /her safety and the protection of
his/her property.

6/91

VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: [phone], FAX: [phone]
VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: [phone] FAX: [phone]
VISONIC LTD. (UK): UNIT 1, STRATTON PARK, DUNTON LANE, BIGGLESWADE, BEDS. SG18 8QS. PHONE: [phone] FAX: [phone]

VISONIC LTD. 1998 MCT-201 D-2261-0 NEW: DE2261- (REV. 4, 4/98)

2 DE2261