Visonic MCS-730AC User Manual

MCS-730/MCS-730 AC

Fully / Mains Powered Wireless Outdoor Siren

1. INTRODUCTION

The MCS-730, powered by 1 or 2 (optional) non-rechargeable batteries,
is fully wireless outdoor siren, designed for installation in areas in which
wiring action is difficult or impossible. It is compatible with control panels
such as PowerMax Pro, PowerMaxComplete, PowerMaxExpress or
Visonic newer panels (not compatible with PowerMax+ and PowerMax
control panel).

The MCS-730 AC is similar to MCS-730 but It is powered by an External
9VAC Adaptor and non-rechargeable backup battery - enables very
long operation time without replacing the battery. The MCS-730 AC
complies with PowerMax+ also.

Features

• Siren and strobe light activation: The siren produces a strong
alarm noise and emits flashing light to deter intruders and guide
police to the site.

Notes:

The duration of the siren's alarm is controlled from the control panel

by setting the "Bell Time" option (refer to alarm system installer
guide, par. 4.4) and should be set according to local authorities
requirements.

The strobe light operates (every 1 second) for 20 minutes after

siren stops or until the system is disarmed, whichever occurs first.

• 2 Types of alarm indication
The siren produces different alarm signals for Burglar and Fire.

• Squawk indication: Squawk (beep) sounds can be used to
indicate alarm system arming (1 squawk) and disarming (2
squawks) by a keyfob (squawk can be enabled from the control
panel User menu).

• Tamper / supervision failure indication: Siren is equipped with
tamper protection, which produces alarm if a burglar attempt to
open the siren's cover or remove siren from wall.

• Low battery voltage alert
The siren reports a low battery message to the alarm system when

battery is about to drain. After low voltage is reported, at least 2
siren alarms are possible before the siren is totally inactive.

• Strobe Light Color: The siren can be purchased with red, blue,
amber or transparent lens, according to the desired strobe light color.

• Siren activity LED: A flashing LED (optional, at the bottom of the
siren front panel) indicates siren activity (can be disabled by an
internal jumper, see fig. 3, step 8)

• 2-way full supervision

• Installation diagnostics

• Self-test function

2. SPECIFICATIONS

Siren Type: One Piezo 109 db. Sound Pressure Level @ 1m, 1.8-3.5

kHz, sweep frequency 7 Hz. Additional piezo is optional.

AC Power Supply Adaptor (MCS-730 AC only):

120 VAC, 60 Hz / 9 VAC, 0.35 A min. (in the U.S.A.)
230 VAC, 50 Hz / 9 VAC, 0.35 A min.

Battery: 3.6V/14.5A/H Lithium battery (EVE ER34615M/w200),

Visonic assembly cat. No. 0-9912-K.

Caution! Risk of explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the manufacturer's instructions.

Battery Life Time:

of 4 minutes Piezo + strobe operation per week).

Current Consumption: Standby - 250µA average, Operation -

300mA average.

Compliance with Standards: EN 50131-1 Grade 2 Class 4,

EN50131-4, EN301489, EN50130-4, EN50130-5, ETSI EN 300 220,
IP55, CFR47 part 15. Designed to comply with Belgium / TO14,
Sweden / SSF1014.

Operating Frequency (MHz): 315, 433.92, 868.95
Supervision Time: 5 minutes
Strobe Light:
Dimensions (LxWxD): 295x186x63mm (11-5/8 x 7-5/16 x 2-1/2 in)
Color: White (with red, blue, amber or transparent lens)
Operating Temperature:

humidity 75%.

Weight (including battery): 970g (34 oz)

3 years (taking into consideration a typical alarm

Pulsed @ 1 sec.

-33°C to 70°C (-27.4°F to 158°F), RH

Note: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user's authority to operate the
equipment.

Installation Instructions

Fig. 1a - External View

IMPORTANT! The MCS-730/MCS-730 AC siren must be installed
on the wall in a vertical position with the screw pointing to the floor

, as illustrated in Figure 1b. The importance of correct

only

positioning of the MCS-730/MCS-730 AC is to enable the siren to
function as a waterproof device.

The siren is fully supervised, 2-way communication device. It
periodically transmits its status signal to the alarm system.

The transmitted signal strength can be measured during the
installation (refer to the alarm system Installer guide, par. 5.2 –
Diagnostic Test).

Upon pressing the self test switch, siren functional check is performed ­low level sounds and flash light indicate that the siren is serviceable.

Remote commander

Door or window

open/close detector

Wireless transmitter

Smoke detector

Motion detector

Hard wired detector

Fig. 1b – Mounting Position

PowerMax+ /

PowerMax Pro /

PowerMaxComplete /

PowerMaxExpress

Figure 2- Typical Integration with the Alarm System

Interference Prevention

This device complies with FCC Rules Part 15. Operation is subject to two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference that may be received or that may cause
undesired operation.
The digital circuit of this device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
residential installations. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio and television reception.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause such interference, which can be verified by
turning the device off and on, the user is encouraged to eliminate the interference
by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one which

supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
Changes or modifications not expressly approved by Visonic Ltd. could void

the user's authority to operate the equipment.

MCS-730 /

MCS-730 AC

D-301680 1

3. INSTALLATION, TESTING AND ENROLLING

3.1 Installation

For

tamper

1

Open screw
plastic cover

2

Using Philips screw­driver, remove screw

and remove cover.

BA

3

Optional step only:

Hang back unit with a screw on mounting

surface to make the next step (drilling

marking) easier.

4

Mark for driling

Drill 5 holes

AC CONFiguration Enable

(ON) / Disable (OFF)

jumper

Optional second battery

location and its connector

5 6

Fasten with 5 screws

Note: There is siren model that is supplied
with battery only (MCS-730) and siren
model that is supplied with 9VAC adaptor
and backup battery (MCS-730 AC).

Siren rear side

220/110 VAC

Self-test button

PM+ / Others

Release catch (A) and open battery cover (B)

7

configuration
jumper

Connect battery / optional battery and

9VAC power to the proper connectors and

set the optional jumpers as desired

Figure 3 – Installation

3.2 Self-Test

Press the self test button (see figure 3 step 8). Low level piezo
sounds and flash lights indicate that the siren is fully operational.

3.3 Configuration (see figure 3, step 8)

LED Keep Alive Jumper Setup:

When it is desired that the Keep Alive LED should blink (every 5
sec.); LED configuration must be set to ON position.

PowerMax+ / Other Jumper Setup (MCS-730 AC only):

When enrolling to the PowerMax+, the internal jumper must be set to
the "PM+" position. When enrolling to other PowerMax control panels
the internal jumper must be set to "others" position.

AC CONF ON/OFF Jumper setup (MCS-730 AC only):

When it is desired to use AC power supply (optional); AC CONF jumper

9VAC connector

LED KEEP ALIVE

Enable (ON)/ Disable

8

(OFF) jumper

3.4 Enrolling

Important Note: The siren is ready to operate 30 seconds after the
enrolling. Pre-enrolled sirens are ready to operate 30 seconds after
power up.

The alarm system must recognize the siren's unique identification code
for command delivery and supervision. To enroll the siren into the alarm
system memory, refer to the ENROLLING section of the alarm system
installation instructions, and momentarily press the Self-Test button (see
figure 3 step 8) when you are instructed.
After the enrolling, close the siren's cover and perform diagnostic test,
as described in the alarm system installer guide, DIAGNOSTIC
section.
Enrolling cancellation, if required, is also described in the alarm
system Installer Guide, ENROLLING section.

9VAC

Note: When external power is
used, set the AC CONF jumper

to ON position (see step 8)

must be set to ON position.

WARRANTY

Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the
“Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve
(12) months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated
under conditions of normal use in accordance with the Manufacturers recommended installation and operation
instructions. Products which have become defective for any other reason, according to the Manufacturers
discretion, such as improper installation, failure to follow recommended installation and operational instructions,
neglect, willful damage, misuse or vandalism , accidental damage, alteration or tampering, or repair by anyone
other than the manufacturer, are not covered by this Warranty.
The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the
Product will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery,
fire or otherwise, or that the Product will in all cases provide adequate warning or protection. The Product,
properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee
or insurance that such events will not occur.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR
LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE
MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR
BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID.

THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS
OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM
PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF
OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.

THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY
AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.

W.E.E.E. Product Recycling Declaration

For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.

Directive 2002/96/EC Waste Electrical and Electronic Equipment.

VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: [phone], FAX: [phone]
VISONIC INC. (U.S.A.): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: [phone]. FAX: [phone]
VISONIC LTD. (UK):
TEL: [phone] FAX: [phone] PRODUCT SUPPORT: [phone]
VISONIC GmbH (D-A-CH): KIRCHFELDSTR. 118, D-40215 DÜSSELDORF, TEL.: [phone], FAX: [phone]
VISONIC IBERICA: ISLA DE PALMA, 32 NAVE 7, POLÍGONO INDUSTRIAL NORTE, 28700 SAN SEBASTIÁN DE LOS REYES, (MADRID), ESPAÑA.

TEL [phone], FAX [phone]. www.visonic-iberica.es
INTERNET: www.visonic.com
©VISONIC LTD. 2010 MCS-730/MCS-730 AC, D-301680 (Rev 4, 06/10)

UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ. TEL: [phone] FAX: [phone].

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this
limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE
EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a
penalty, and shall be the complete and exclusive remedy against the Manufacturer.
When accepting the delivery of the Product, the Purchaser agrees to the said c onditions of sale and warranty and
he recognizes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of incidental or c onsequential damages, so these
limitations may not apply under certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any
telecommunication or electronic equipment or any programs.
The Manufacturers obligations under this W arranty are limited solely to repair and/or replace at the
Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or replacement
shall not extend the original Warranty period. The Manufacturer shall not be responsible for dismantling and/or
reinstallation costs. To exercise this W arranty the Product must be returned to the Manufacturer freight pre-paid
and insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this
Warranty.
This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to
act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the
Product only. All products, accessories or attachments of others used in conjunction with the Product, including
batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the
malfunction of the Product due to products, accessories, or attachments of others, including batteries, used in
conjunction with the Products. This Warranty is exclusive to the original Purchaser and is not assignable.
This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is
contrary to the Law in the state or country were the Product is supplied shall not apply.

Warning:

The user must follow the Manufacturer’s installation and operational instructions including testing the

Product and its whole system at least once a week and to take all necessary precautions for his/her s afety and
the protection of his/her property. 1/08

2 D-301680