Vision Technology D410-TP12H33V12, D410-TP22H33V12 Instruction Manual

COLOUR VANDAL PROOF CAMERA

D410-TP12H33V12
D410-TP22H33V12

Dimensions : mm

INSTRUCTION MANUAL

About this Manual

Before installing and using the camera, please read this manual
carefully. Be sure to keep it safe for later reference.

SPECIFICATION

PRECAUTIONS

D410-TP12H33V12 D410-

MODEL
General Spec

PAL

CCD Type

1/3" 470k Pixels
Color

Total number of pixels 795(H) X 596(V)
Min illumination

Video Output
Resolution

S/N Ratio
Shutter speed x128 : 1/50~1/120,000sec

Sync System
White Balance

OSD

Built-in

DAY / NIGHT

AUTO / EXTERN / B/W / COLOR

DNR LOW, MIDDLE, HIGH, OFF

Power Input
Video Output

Voltage
Power Consumption

Lens
Dimension
Weight
Case Color
Operation temp

In storage temp
Operation humidity

-10Ԩ׽+55

Ԩ

-20Ԩ׽+70

Ԩ

Under 90

％

(Non-condensing)

890g
Ivory

Max [DC12V : 3.0 W]

Mechanical Spec

3.3~12.0 mm / DC LENS
140(ø) X 105(H)mm

Wire
BNC Cable

Electric Spec

DC 12V ( 10.8V ~ 13.2V
)

50dB (AGC off, weight ON)

Internal / External
ATW/AWC/MANUAL (1800 ˚K ~ 10,500 ˚K)

Connectors

0.3 Lux/F1.2(50 IRE, AGC HIGH, DNR HIGH)

1.0Vp-p/75 ohm Composite
520 TV Lines(Min)

DC10-20V/ AC 20-28V 50Hz

Max ?W

■ Do not open or modify
Do not open the cabinet except during maintenance and
installation, as it may endanger you safety and cause damage.

■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
inside the camera. It could cause fire, short-circuits or
damage.

■ Be careful when handling the unit
To prevent damage, do not drop the cam era or subject
it to strong shock or vibration.

■ Install away from electric or magnetic fields

■ Protect from humidity and dust

■ Protect from high temperature

Be careful when installing close to the ceiling , in a kitchen or
boiler room, as the temperature may raise to high levels.
Always use the camera within its operating temperature range.

■ Cleaning
Dirt can be removed from the cabinet only by w iping it
with a soft cloth moistened with a soft detergent solution.

■ Mounting Surface
The mounting surface material must be strong enough to
secure the camera.

■ Ingress Protection
Ensure all cab leentry points are sealed with silicone se alent
to prevent moisture ingress

■ CONNECTIONS

About this Manual

Before installing and using the camera, please read this manual
carefully. Be sure to keep it safe for later reference.

TROUBLESHOOTING

SPECIFICATION

Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact you r service ce n ter.

■ If no im age appear s

Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (incorrectlens level) ?
Is there adequate illumination?

■ If the image is unclear

Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?

WARNING:
TO PREVENT THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THE
INSIDE OF THIS APPLIANCE TO RAIN OR
MOISTURE. SEAL CABLE ENTRY POINTS TO
PREVENT MOISTURE FROM INTO THE
CAMERA.

CAUTION :

Check for polarity when using a DC 12V.

CONNECTOR AND CAMERA SETTING

INSTALLATION

PRECAUTIONS

DC12V AC24V

B

A

C

D

E F

D410-TP12H33V12 D410-

MODEL
General Spec

PAL

CCD Type

1/3" 470k Pixels
Color

Total number of pixels 795(H) X 596(V)
Min illumination

Video Output
Resolution

S/N Ratio
Shutter speed x128 : 1/50~1/120,000sec

Sync System
White Balance

OSD

Built-in

DAY / NIGHT

AUTO / EXTERN / B/W / COLOR

DNR LOW, MIDDLE, HIGH, OFF

Power Input
Video Output

Voltage
Power Consumption

Lens
Dimension
Weight
Case Color
Operation temp

In storage temp
Operation humidity

-10Ԩ׽+55

Ԩ

-20Ԩ׽+70

Ԩ

Under 90

％

(Non-condensing)

890g
Ivory

Max [DC12V : 3.0 W]

Mechanical Spec

3.3~12.0 mm / DC LENS
140(ø) X 105(H)mm

Wire
BNC Cable

Electric Spec

DC 12V ( 10.8V ~ 13.2V
)

50dB (AGC off, weight ON)

Internal / External
ATW/AWC/MANUAL (1800 ˚K ~ 10,500 ˚K)

Connectors

0.3 Lux/F1.2(50 IRE, AGC HIGH, DNR HIGH)

1.0Vp-p/75 ohm Composite
520 TV Lines(Min)

DC10-20V/ AC 20-28V 50Hz

Max ?W

■ Do not open or modify
Do not open the cabinet except during maintenance and
installation, as it may endanger you safety and cause damage.

■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
inside the camera. It could cause fire, short-circuits or
damage.

■ Be careful when handling the unit
To prevent damage, do not drop the cam era or subject
it to strong shock or vibration.

■ Install away from electric or magnetic fields

■ Protect from humidity and dust

■ Protect from high temperature

Be careful when installing close to the ceiling , in a kitchen or
boiler room, as the temperature may raise to high levels.
Always use the camera within its operating temperature range.

■ Cleaning
Dirt can be removed from the cabinet only by w iping it
with a soft cloth moistened with a soft detergent solution.

■ Mounting Surface
The mounting surface material must be strong enough to
secure the camera.

■ Ingress Protection
Ensure all cab leentry points are sealed with silicone se alent
to prevent moisture ingress

1. Use the supplied L-wrench to remove the four fixing
screws (B) of do me co ve r (A).

2. Align the camera unit with the surface of the ceiling,
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill t he four
holes.

3. Cut a hole (diameter2.9in. 73m m) in the ceiling for
routing the cables.

4. Pass the power cable (E) and video cable (F) from the
camera unit through the cable hole in the ceiling .

5. Align the four screw holes in the camera unit (D) with
the screw holes in the ceiling, and then sec ure the
camera in place by tightening the four or more screws
(C) through the washers. Remember to use the base
gasket.

6. Carry out the settings and adjustments for the camera.

7. Ensure all cable entry points (rear or side) are sealed
with silicone sealent to preve nt moisture ingress.
Failure to observe this may result in condensation
deposits that will reduce the IR response of the camera.

About this Manual

Before installing and using the camera, please read this manual
carefully. Be sure to keep it safe for later reference.

TROUBLESHOOTING

SPECIFICATION

Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact you r service ce n ter.

■ If no im age appear s

Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (incorrectlens level) ?
Is there adequate illumination?

■ If the image is unclear

Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?

WARNING:
TO PREVENT THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THE
INSIDE OF THIS APPLIANCE TO RAIN OR
MOISTURE. SEAL CABLE ENTRY POINTS TO
PREVENT MOISTURE FROM INTO THE
CAMERA.

CAUTION :

Check for polarity when using a DC 12V.

CONNECTOR AND CAMERA SETTING

INSTALLATION

PRECAUTIONS

DC12V AC24V

B

A

C

D

E F

D410-TP12H33V12 D410-

MODEL
General Spec

PAL

CCD Type

1/3" 470k Pixels
Color

Total number of pixels 795(H) X 596(V)
Min illumination

Video Output
Resolution

S/N Ratio
Shutter speed x128 : 1/50~1/120,000sec

Sync System
White Balance

OSD

Built-in

DAY / NIGHT

AUTO / EXTERN / B/W / COLOR

DNR LOW, MIDDLE, HIGH, OFF

Power Input
Video Output

Voltage
Power Consumption

Lens
Dimension
Weight
Case Color
Operation temp

In storage temp
Operation humidity

-10Ԩ׽+55

Ԩ

-20Ԩ׽+70

Ԩ

Under 90

％

(Non-condensing)

890g
Ivory

Max [DC12V : 3.0 W]

Mechanical Spec

3.3~12.0 mm / DC LENS
140(ø) X 105(H)mm

Wire
BNC Cable

Electric Spec

DC 12V ( 10.8V ~ 13.2V
)

50dB (AGC off, weight ON)

Internal / External
ATW/AWC/MANUAL (1800 ˚K ~ 10,500 ˚K)

Connectors

0.3 Lux/F1.2(50 IRE, AGC HIGH, DNR HIGH)

1.0Vp-p/75 ohm Composite
520 TV Lines(Min)

DC10-20V/ AC 20-28V 50Hz

Max ?W

■ Do not open or modify
Do not open the cabinet except during maintenance and
installation, as it may endanger you safety and cause damage.

■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
inside the camera. It could cause fire, short-circuits or
damage.

■ Be careful when handling the unit
To prevent damage, do not drop the cam era or subject
it to strong shock or vibration.

■ Install away from electric or magnetic fields

■ Protect from humidity and dust

■ Protect from high temperature

Be careful when installing close to the ceiling , in a kitchen or
boiler room, as the temperature may raise to high levels.
Always use the camera within its operating temperature range.

■ Cleaning
Dirt can be removed from the cabinet only by w iping it
with a soft cloth moistened with a soft detergent solution.

■ Mounting Surface
The mounting surface material must be strong enough to
secure the camera.

■ Ingress Protection
Ensure all cab leentry points are sealed with silicone se alent
to prevent moisture ingress

1. Use the supplied L-wrench to remove the four fixing
screws (B) of do me co ve r (A).

2. Align the camera unit with the surface of the ceiling,
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill t he four
holes.

3. Cut a hole (diameter2.9in. 73m m) in the ceiling for
routing the cables.

4. Pass the power cable (E) and video cable (F) from the
camera unit through the cable hole in the ceiling .

5. Align the four screw holes in the camera unit (D) with
the screw holes in the ceiling, and then sec ure the
camera in place by tightening the four or more screws
(C) through the washers. Remember to use the base
gasket.

6. Carry out the settings and adjustments for the camera.

7. Ensure all cable entry points (rear or side) are sealed
with silicone sealent to preve nt moisture ingress.
Failure to observe this may result in condensation
deposits that will reduce the IR response of the camera.

■ LENS ADJUSTMENTS

■ CAMERA SETTINGS

● OSD SWITCH FUNCTION

CONNECTIONS AND CAMERA SETTINGS

1. Adjust the pan(360˚) and tilt(90˚) position.

2. Setting the zoom position by using Zoom Lever Screw.

3. Setting the focus by using Focus Lever Screw.

SETUP FUNTION SUMMARY

when using BUILT-IN lens, selecting
MANUAL will allow the aperture to be fixed
MANUAL: 1/60(50) ~
1/120,000sec, x2~ x128

WHITE BAL.

ATW, MANUAL, AWC

ATW: 1,800 ~10,500 ˚K

BACKLIGHT

OFF, LOW, MIDDLE, HIGH

Backlight compen sa t i on

AGC

NORMAL, HIGH,OFF

the Brightness can be adjusted(1 ~ 70)

MIDDLE

, HIGH, OFF, LOW

when AGC is turned off,
DNR does not operate.
when AGC is turned off,

LENS

DC(=25), MANUAL

SHUTTER

ESC, MANUAL, FLK, OFF

SENS-UP

AUTO(=X6)

, OFF

OSD

DNR

CONNECTIONS AND CAMERA SETTINGS

1. Adjust the pan(360˚) and tilt(90˚) position.

2. Setting the zoom position by using Zoom Lever Screw.

3. Setting the focus by using Focus Lever Screw.

SETUP FUNTION SUMMARY

when using BUILT-IN lens, selecting
MANUAL will allow the aperture to be fixed
MANUAL: 1/60(50) ~
1/120,000sec, x2~ x128

WHITE BAL.

ATW, MANUAL, AWC

ATW: 1,800 ~10,500 ˚K

BACKLIGHT

OFF, LOW, MIDDLE, HIGH

Backlight compen sa t i on

AGC

NORMAL, HIGH,OFF

the Brightness can be adjusted(1 ~ 70)

MIDDLE

, HIGH, OFF, LOW

when AGC is turned off,
DNR does not operate.
when AGC is turned off,

SENS-UP does not oper ate.
SPECIAL Refer to the section below
EXIT Save the settings then exit

SPECIAL FUNTION SUMMARY

uppercase or lowercase,

OFF

maximum length for the name

/numeral 0~9/-, null display is limited 15 letters.

AUTO :

daytime → colour mode ,

night-time→ B/W mode

B/W : Always in B/W mode

COLOUR: Always colour mode

EXTERN : CDS EXTERNAL SIGNAL

LL mode: you can adjust

desired phase from 0˚ ~ 359˚,

auto detection
MOTION ON mode: AREA(4 programmable
DETECTION zone /SIZE), the word

MOTION DETECTE D" appears on the

screen when movement is detected

ON mode:AREA(4x programmable

zones) /SIZE/TONE
MIRROR

OFF

, ON

set a horizontal image inversion.

the available range

of level is 0 ~ 31.

Reset all settings to factory

defaults

save the SPECIAL MENU and then

RESET

RETURN

LENS

DC(=25), MANUAL

SHUTTER

ESC, MANUAL, FLK, OFF

SENS-UP

AUTO(=X6)

, OFF

CAMERA ID

OFF

, ON

PRIVACY

OFF

, ON

SHARPNESS

OFF,

ON(=8)

OSD

DNR

DAY NIGHT

AUTO

, B/W, EXTERN, COLOR

SYNC

INT

, LL (n/a for 1 2 VDC model)

CONNECTIONS AND CAMERA SETTINGS

1. Adjust the pan(360˚) and tilt(90˚) position.

2. Setting the zoom position by using Zoom Lever Screw.

3. Setting the focus by using Focus Lever Screw.

SETUP FUNTION SUMMARY

when using BUILT-IN lens, selecting

MANUAL will allow the aperture to be fixed

MANUAL: 1/60(50) ~

1/120,000sec, x2~ x128
WHITE BAL.

ATW, MANUAL, AWC

ATW: 1,800 ~10,500 ˚K
BACKLIGHT

OFF, LOW, MIDDLE, HIGH

Backlight compen sa t i on
AGC

NORMAL, HIGH,OFF

the Brightness can be adjusted(1 ~ 70)

MIDDLE

, HIGH, OFF, LOW

when AGC is turned off,

DNR does not operate.

when AGC is turned off,

SENS-UP does not oper ate.
SPECIAL Refer to the section below
EXIT Save the settings then exit

SPECIAL FUNTION SUMMARY

uppercase or lowercase,

OFF

maximum length for the name

/numeral 0~9/-, null display is limited 15 letters.

AUTO :

daytime → colour mode ,

night-time→ B/W mode

B/W : Always in B/W mode

COLOUR: Always colour mode

EXTERN : CDS EXTERNAL SIGNAL

LL mode: you can adjust

desired phase from 0˚ ~ 359˚,

auto detection
MOTION ON mode: AREA(4 programmable
DETECTION zone /SIZE), the word

MOTION DETECTE D" appears on the

screen when movement is detected

ON mode:AREA(4x programmable

zones) /SIZE/TONE
MIRROR

OFF

, ON

set a horizontal image inversion.

the available range

of level is 0 ~ 31.

Reset all settings to factory

defaults

save the SPECIAL MENU and then

return to the SETUP MENU

RESET

RETURN

LENS

DC(=25), MANUAL

SHUTTER

ESC, MANUAL, FLK, OFF

SENS-UP

AUTO(=X6)

, OFF

CAMERA ID

OFF

, ON

PRIVACY

OFF

, ON

SHARPNESS

OFF,

ON(=8)

OSD

DNR

DAY NIGHT

AUTO

, B/W, EXTERN, COLOR

SYNC

INT

, LL (n/a for 1 2 VDC model)