Visioneer Patriot 780 User Manual

Visioneer®
Patriot 780 Scanner
User's Guide

for Windows

Visioneer

Patriot 780 Scanner

User’s Guide

FOR WINDOWS

COPYRIGHT INFORMATION

Copyright © 2006 Visioneer, Inc.
Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws.
The Visioneer brand name and logo are registered trademarks of Visioneer, Inc. The OmniPage Pro brand name and logo are registered trademarks of Nuance

Communications, Inc. Kofax VRS is a copyright of Kofax Image Products. QuickScan is a trademark and ISIS is a registered trademark of Captiva Software
Corporation. Adobe®, Adobe® Acrobat®, Acrobat® Reader®, and the Adobe® Acrobat® PDF® logo are registered trademarks of Adobe Systems
Incorporated in the United States and/or other countries. The Adobe PDF logo will appear in this product’s software, and full access to Adobe software features
is only available if any Adobe product is installed on your computer.

This product is covered by one or more of the following patents: 6, 480, 304; 5,818,976; 5,499,108; 5,517,332.
Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation. ZyINDEX is a registered trademark of

ZyLAB International, Inc. ZyINDEX toolkit portions, Copyright © 1990-1998, ZyLAB International, Inc. All Rights Reserved. All other products mentioned
herein may be trademarks of their respective companies.

Information is subject to change without notice and does not represent a commitment on the part of Visioneer. The software described is furnished under a
licensing agreement. The software may be used or copied only in accordance with the terms of such an agreement. It is against the law to copy the software on
any medium except as specifically allowed in the licensing agreement. No part of this document may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying, recording, or information storage and retrieval systems, or translated to another language, for any
purpose other than the licensee's personal use and as specifically allowed in the licensing agreement, without the express written permission of Visioneer.

Part Number: 05-0709-000

Restricted Rights Legend

Use, duplication, or disclosure is subject to restrictions as set forth in contract subdivision (c)(1)(ii) of the Rights in Technical Data and Computer Software
Clause 52.227-FAR14. Material scanned by this product may be protected by governmental laws and other regulations, such as copyright laws. The customer
is solely responsible for complying with all such laws and regulations.

Visioneer's Limited Product Warranty

IF YOU FIND PHYSICAL DEFECTS IN THE MATERIALS OR THE WORKMANSHIP USED IN MAKING THE PRODUCT DESCRIBED IN
THIS DOCUMENT, VISIONEER WILL REPAIR, OR AT ITS OPTION, REPLACE THE PRODUCT AT NO CHARGE TO YOU, PROVIDED YOU
RETURN IT (POSTAGE PREPAID, WITH PROOF OF YOUR PURCHASE FROM THE ORIGINAL RESELLER) DURING THE 90-DAY PERIOD
AFTER THE DATE OF YOUR ORIGINAL PURCHASE OF THE PRODUCT. UPON RECEIPT DURING THE INITIAL 90-PERIOD BY
VISIONEER OF A VALID REGISTRATION OF THE PRODUCT, THIS LIMITED PRODUCT WARRANTY PERIOD IS EXTENDED TO THE
12-MONTH PERIOD AFTER THE DATE OF YOUR ORIGINAL PURCHASE. IF A VALID REGISTRATION IS NOT RECEIVED DURING THE
INITIAL 90-DAY PERIOD, THE 12-MONTH WARRANTY IS NO LONGER AVAILABLE AND YOUR PRODUCT WARRANTY WILL
TERMINATE AFTER THE 90-DAY INITIAL PERIOD EXPIRES.

THIS IS VISIONEER'S ONLY WARRANTY AND YOUR EXCLUSIVE REMEDY CONCERNING THE PRODUCT, ALL OTHER
REPRESENTATIONS, WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, WRITTEN OR ORAL, INCLUDING ANY WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE EXPRESSLY EXCLUDED. AS A RESULT,
EXCEPT AS SET OUT ABOVE, THE PRODUCT IS SOLD “AS IS” AND YOU ARE ASSUMING THE ENTIRE RISK AS TO THE PRODUCT'S
SUITABILITY TO YOUR NEEDS, ITS QUALITY AND ITS PERFORMANCE.

IN NO EVENT WILL VISIONEER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM ANY DEFECT IN THE PRODUCT OR FROM ITS USE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

All exclusions and limitations in this warranty are made only to the extent permitted by applicable law and shall be of no effect to the extent in conflict with the
express requirements of applicable law.

RoHS and WEEE Compliance

This product is compliant with RoHS Regulations of the European Parliament and Council Directive on the Restrictions of the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment (2002/95/EC), and with the Waste Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC).

FCC Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for the class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and if not installed, and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or mor

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with

FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in
interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer
could void the user's authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.

e of the following measures:

TABLE OF CONTENTS i

TABLE OF CONTENTS

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

The Visioneer Patriot 780 Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . 2

What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1: Assemble the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 2: Install the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 3: Connect the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Step 4: Connect the USB Cable and Turn on the Power . . . . . . . . . 16

Additional Applications for Your Scanner . . . . . . . . . . . . . . . . . 21

Register Your Scanner and Check for Updates . . . . . . . . . . . . . . . . . 24

Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Scanning Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Loading a Stack of Documents . . . . . . . . . . . . . . . . . . . . . . . . . 26

Scanning a Single Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Scan from the OneTouch Button Panel . . . . . . . . . . . . . . . . . . . . . . 29

Check the Scan Settings Before Scanning . . . . . . . . . . . . . . . . . 31

Using the OneTouch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

About the OneTouch Button Panel’s Names and Icons . . . . . . . 34

The Default OneTouch Settings on Your Scanner . . . . . . . . . . 35

Configuring the OneTouch Buttons . . . . . . . . . . . . . . . . . . . . . . . . 36

About the OneTouch Properties Window . . . . . . . . . . . . . . . . . 37

Selecting New Settings for a Button . . . . . . . . . . . . . . . . . . . . . 40

Setting Destination Application Properties . . . . . . . . . . . . . . . . 42

Selecting Page Format Options . . . . . . . . . . . . . . . . . . . . . . . . . 50

Renaming a OneTouch Button . . . . . . . . . . . . . . . . . . . . . . . . . 55

ii TABLE OF CONTENTS

Selecting Options for the OneTouch Properties Window . . . . . 56

Creating a New Scan Configuration . . . . . . . . . . . . . . . . . . . . . 60

Editing or Deleting Scan Configurations . . . . . . . . . . . . . . . . . . 75

Configuring Before Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Scanning with Optical Character Recognition (OCR) . . . . . . . . 78

Scanning with sPDF or nPDF and Searching for Text . . . . . . . . 86

Scan and Burn to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Scanning with Event Forwarding . . . . . . . . . . . . . . . . . . . . . . . . 92

Creating an HTML Web Page from Your Scanned Documents 94

Transferring Scanned Documents to Storage . . . . . . . . . . . . . . . 96

Checking the Hardware and Setting the Lamp Power Saving . 101

Scanning with the TWAIN Interface . . . . . . . . . . . . . . . . . . . . . . 104

The Basic Steps to Open the TWAIN Interface . . . . . . . . . . . . 105

The Two TWAIN Interface Options . . . . . . . . . . . . . . . . . . . . . . . 106

Scanning from the TWAIN Basic Interface . . . . . . . . . . . . . . . 107

Scanning from the TWAIN Advanced Interface . . . . . . . . . . . 109

Adjusting the Image with the Advanced Interface . . . . . . . . . . 112

Adjusting the Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Adjusting the Brightness and Contrast . . . . . . . . . . . . . . . . . . . 116

Adjusting Gamma, Saturation, and Color Hue . . . . . . . . . . . . 117

Adjusting Input Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Creating a New Advanced Interface Profile . . . . . . . . . . . . . . . 121

Display the Device Configuration . . . . . . . . . . . . . . . . . . . . . . 122

Scanning with the WIA Interface. . . . . . . . . . . . . . . . . . . . . . . . . 123

Fine Tuning Your Scans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Scanning with the ISIS Interface . . . . . . . . . . . . . . . . . . . . . . . . . 129

Adjusting the ISIS Scan Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Scanning from ISIS in Other Applications . . . . . . . . . . . . . . . . . . . 137

TABLE OF CONTENTS iii

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Cleaning the Scanner Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Cleaning the Automatic Document Feeder . . . . . . . . . . . . . . . 139

Replacing the ADF Pad Assembly . . . . . . . . . . . . . . . . . . . . . . 140

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

Error Light Troubleshooting Codes . . . . . . . . . . . . . . . . . . . . . 144

Uninstalling Your Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

To Install Another Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Visioneer Patriot 780 Scanner Specifications . . . . . . . . . . . . . . . . . 147

Visioneer Patriot 780 Scanner Parts List . . . . . . . . . . . . . . . . . . . . 148

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

iv TABLE OF CONTENTS

WELCOME

Your new Visioneer Patriot 780 scanner can quickly scan single-sided or
double-sided stacks of color and black-and-white documents, up to

11.7" x 17" with the Automatic Document Feeder and up to 11.69" x

16.53" (A3 paper) on the Flatbed Glass.

WHAT’S IN THE BOX

Before proceeding, check the contents of the box. If items are missing or
damaged, contact the dealer where you purchased the scanner.

Power Supply

Visioneer Patriot 780 Scanner

Two CD’s

Disc 1 and Disc 2

Replacement ADF PadPower Cord USB Cable

Technical Support Card

VISIONEER PATRIOT 780 SCANNER USER’S GUIDE 1

User GuideQuick Install Guide

2 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

THE VISIONEER PATRIOT 780 SCANNER

canner cover

ocument pad

lass

eference frame

aper stop
aper guide extension

aper guides

utomatic Document Feeder (ADF)
DF cover release

canner lock

tatus lights

Power switch
Power jack
USB port

ADF port
ADF cable

THE VISIONEER PATRIOT 780 SCANNER 3

Scanner cover—Protects the document from light and contamination during scanning.
Close the cover to put a stack of documents in the Automatic Document Feeder (ADF).

Document pad—Holds documents in place on the scanner glass.
Glass—Documents are placed face down, aligned at the arrow symbol.
Reference frame—Marks on the border of the glass show where to align various paper sizes.
Paper stop—Holds documents in place as they are ejected from the Automatic Document

Feeder.

Paper guide extension—Unfolds to support multiple document lengths.
Paper guides—Holds documents in place. Adjust to fit the paper size.

Automatic Document Feeder (ADF)—Feeds a stack of documents onto the glass for
scanning. The ADF can hold up to 50 pages at a time.

ADF cover release—Opens the ADF cover to clear paper jams.
Scanner lock—Locks or unlocks the scanning head. The lock must be unlocked for the

scanner to scan. The lock should always be locked when transporting the scanner.

Power light—Shows the scanner is receiving power.
Status lights—Shows the scanner’s status:

Power light shows the scanner is receiving power.
Ready light is a steady green when the scanner is ready to begin scanning.
Error light flashes amber to indicate a problem. Refer to “Error Light Troubleshooting

Codes” on page 144 for additional details about the status lights.

Power switch—On/Off power switch.
Power jack—Connects the power cord to the scanner.
Universal Serial Bus (USB) port—Connects the scanner to the computer.
ADF port—Connects the ADF cable from the Automatic Document Feeder to the scanner

body.
ADF cable—Supplies power from the scanner body to the Automatic Document Feeder.

The cable must be securely plugged into the ADF port for the Automatic Document Feeder
to work.

4 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

WHAT YOU NEED

An IBM-compatible Pentium PC, or AMD equivalent with:

■ A CD-ROM drive

■ An available Universal Serial Bus (USB) port

■ Microsoft Windows operating system: 2000 (Service Pack 4) or XP

(Service Pack 1 and 2)

■ A minimum of 512 MB (megabytes) of internal memory (RAM)

■ 200 MB minimum of free hard disk space

A VGA Monitor

The recommended settings for your monitor are:

■ High Color (16-bit) or True Color (24-bit or 32-bit)

■ Resolution set to at least 800 x 600 pixels

To set your monitor’s colors and resolution:

■ Open the Windows Control Panel

■ Double-click on Display then select the Settings tab

DOCUMENTATION

Your scanner is delivered with the following documentation:

■ Quick Install Guide—Abbreviated installation instructions.

■ Visioneer Patriot 780 Scanner User’s Guide—Contains detailed

installation, scanning, configuration, and maintenance information;
a copy is also available on the Disc 1 Installation CD.

■ Online Help—For the scanner configuration, TWAIN, and WIA

interfaces.

BEFORE YOU BEGIN 5

Installation

Installation is a quick, four-step process:

1. Assemble the scanner

2. Install the software

3. Connect the power supply

4. Connect the USB cable and turn on the power

BEFORE YOU BEGIN

Please make sure of the following before you begin installation:

■ If your computer has AntiVirus or AntiSpyware software running,

you may see messages during installation asking you to allow the
installation to proceed. Although the messages will differ based on
the software your computer is running, in each case you should
allow the installation to proceed. Alternatively, you can turn off the
AntiVirus or AntiSpyware software before installing your scanner,
but if you do, make sure to turn it back on again when installation
is finished.

■ If you already have a scanner connected to your computer, it is

recommended that you remove that scanner’s driver program prior
to installing your Visioneer Patriot 780 scanner. While in some
cases you can configure your computer to have another
manufacturer’s scanner operational on your computer in
conjunction with the Visioneer Patriot 780 scanner, we do not
recommend this configuration as you may lose some of the driver
functionality on one, or both of the units. You can remove these
programs from the Windows Add/Remove programs list. Please
refer to the user manual provided with your other scanner hardware
for instructions about removing the driver and software for that
unit.

6 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

STEP 1: ASSEMBLE THE SCANNER

To assemble the scanner:

1. Remove all shipping tape from the top and bottom of the scanner.

2. Holding the top with two hands, carefully lower it onto the Flatbed

so the two hinges slide into their slots.

3. Remove any protective foam from the ADF Cover Release, then

press the ADF Cover Release and open the Automatic Document
Feeder cover.

ADF Cover Release

4. Carefully remove any foam particles that may have gotten inside the

Automatic Document Feeder. Close the cover so it snaps shut.

STEP 1: ASSEMBLE THE SCANNER 7

5. Flip the Paper Guide up to reveal the two legs folded into the

bottom of the tray.

6. Swing out the legs, then lower the Paper Guide Tray so the legs fit

into their slots.

7. Flip up the Paper Guide Extension to fully extend it.

8 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

8. Slide the Scanner Locking Tab to its unlocked position.

Note: The Locking Tab protects the scanner’s scan head by holding it
securely in position. Lock the scanner when transporting it from one
location to another, but remember to unlock it before scanning. The
scanner will not scan when locked.

9. Plug the ADF cable into the ADF port. Make sure the ADF cable is

securely plugged into the port. The ADF will not function properly
if the ADF cable is loose or unplugged.

10. When you’re finished assembling the scanner, place it on a level

surface on your desk. If the scanner is on an uneven surface, it may
stall when scanning from the Flatbed.

11. Proceed to “Step 2: Install the Software.”

STEP 2: INSTALL THE SOFTWARE 9

STEP 2: INSTALL THE SOFTWARE

Note: The software is on the two CD’s you received with your scanner.
Please be sure to install from Disc 1 first.

To install the software:

1. Start Microsoft Windows and make sure no other applications are

running.

2. Insert Disc 1 into your computer’s CD-ROM drive.

The Installation menu automatically opens.

Note: If the CD does not start, check the following:

■ Make sure you have inserted Disc 1.

■ Make sure the CD drive’s door is completely shut.

■ Make sure the CD was inserted in the drive in the proper

direction (label side up).

To launch the CD manually:

■ Open the Windows option for My Computer. You can do this

by double-clicking on the My Computer icon on your desktop.

■ Double-click the icon for your CD-ROM drive.

■ The Installation menu for the CD should now open.

If the menu does not open:

■ From the list of files on the CD, double-click the file named

START32.EXE.

10 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

3. On the Installation menu, select Install Products.

4. Make sure the boxes for Scanner Driver and OmniPage Pro

checked.

®

are

STEP 2: INSTALL THE SOFTWARE 11

Note: The OmniPage Pro software is required for installation and
provides extensive Optical Character Recognition (OCR) capabilities
for your scanner software. It also adds special formats to the scanner’s
OneTouch 4.0 software for creating searchable PDF files (known as
sPDF and nPDF). Please note: if you do not install the OmniPage Pro
software now, but install it later, you may need to restart your
computer before the sPDF and nPDF formats are available in the
OneTouch 4.0 software.

5. Click Install Now.

6. The Select Language window opens. Click the drop-down menu

arrow and select the language you want to use. Click OK.

7. The Welcome to the OneTouch 4.0 Setup Wizard opens.

8. Click Next.

9. On the Visioneer License Agreement window, read the license

agreement. If you accept the terms, select I Agree then click Next.
If you choose not to accept the license agreement, the installation

will terminate and the scanner driver will not be installed.

12 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

The next window lists the choices of the drivers that you can install
for your scanner.

Note: Some of the options
listed in this window may
not be available when you
purchase your scanner.

Please visit our web site at:
www.visioneer.com
for the latest updates.

10. Select the option you want.

Note: If your computer is running Windows XP, Microsoft’s
Windows Image Acquisition (WIA) interface for scanning is always
available, regardless of your selection on this window.

■ Full Install (OneTouch, TWAIN, and ISIS)—This is the

recommended installation. It installs the OneTouch 4.0
software which provides the necessary driver software for the
scanner. It also installs scanning interfaces for TWAIN and the
ISIS driver. Installing this option means that you can use several
different methods to scan, as explained in this User Guide.

■ TWAIN and ISIS—The TWAIN and ISIS drivers are installed.

The OneTouch 4.0 Monitor will not run and you cannot use the
OneTouch features. You can use the Visioneer TWAIN driver to
scan from TWAIN applications. You can also scan from
applications that use the ISIS driver. You will not be able to use
the Scan button on the scanner.

STEP 2: INSTALL THE SOFTWARE 13

■ TWAIN only—The TWAIN driver is installed without the

OneTouch 4.0 software or the ISIS driver. You can use the
Visioneer TWAIN driver to scan from TWAIN applications.
You will not be able to use the Scan button on the scanner.

■ ISIS only—The ISIS driver is installed. You can use applications

that use the ISIS driver, such as QuickScan. You will not be able
to use the Scan button on the scanner. You will not be able to use
the Visioneer TWAIN driver.

Note: If you decide to change your scanner’s installed drivers later on,
you must first uninstall the drivers the scanner is currently using. See
“To Install Another Driver” on page 146.

11. Click Next.

During installation of the driver you will see this window asking
you to select an image for your Color Space setting.

The Color Space setting sets the gamma value for the scanner so
scanned items look good on your monitor. Gamma controls the
brightness of the midtones of colors. That setting can be changed
later on as you’re scanning.

12. Select the option that looks best to you and click Next.

14 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

The driver installation will now begin.

13. STOP when you see the “Complete the installation by connecting

your hardware” window. Do NOT click OK yet. Leave the window
open and proceed to “Step 3: Connect the Power Supply” on
page 15.

Reminder: If your computer is running AntiVirus or AntiSpyware
software, you may see messages asking you to allow the installation.
Select the option to allow the installation to proceed.

Note: If you want to see more information about your scanner and a
quick explanation of how to use the OneTouch features, click the
More button on the window. When you’re finished, return to the
window above to continue with the installation process.

STEP 3: CONNECT THE POWER SUPPLY 15

STEP 3: CONNECT THE POWER SUPPLY

Connect the power supply and power cord, and plug the power supply
into an electrical outlet.

To c o n n e c t yo u r V i s i on eer Patriot 780 scanner:

1. Plug the power supply into the power port on the scanner.

Note: Only use the power supply [model number: 077-242090-I3
(YC-1050CAN1352PR)] included with your scanner. Connecting any
other type of power supply may damage your scanner, and will void its
warranty.

2. Plug the power cord into the power supply then into a wall outlet.

Now proceed to the next section, “Step 4: Connect the USB Cable
and Turn on the Power.”

16 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

STEP 4: CONNECT THE USB CABLE AND TURN ON THE

OWER

P

The Visioneer Patriot 780 scanner connects to any available USB port.
Check your computer’s manual for USB port locations.

Note: You can connect the scanner to your computer while the
computer is running. You do not have to shut down your computer.

1. Remove any protective tape from the USB cable.

2. Plug the USB cable into the USB port on the scanner and then into

a USB port on the computer. Connection to a USB 2.0 High Speed
port provides optimum performance, however your scanner will
also connect to a USB 1.1 port.

USB

The USB symbol, as seen in the above diagram, identifies the
location of the USB port on your computer. If the plug does not
attach easily, make sure that you are plugging it in correctly. Do not
force the plug into the connection.

You can also connect the scanner to a USB port on the computer’s
keyboard if it has one, or to a USB hub. If you use a USB hub, it
must have its own power supply already plugged into an electrical
outlet.

STEP 4: CONNECT THE USB CABLE AND TURN ON THE POWER 17

Note: If you have not installed the scanner driver, unplug the USB
cable from the computer and install the software now. When the
driver installation is complete, a message tells you when to connect
the scanner.

3. Turn on the power switch, located on the back of the scanner to the

left of the power port.

The status light comes on and flashes indicating that the scanner is
receiving power.

If you are using Windows XP Service Pack 2, and have plugged the
USB cable into a USB 1.1 port, an information bubble may open
explaining that “A HI-SPEED USB device is plugged into a non­HI-SPEED USB hub”. Plug the USB cable into a USB 2.0 port (if
available) or just disregard the message. If you leave it plugged into
the USB 1.1 port, your scanner may scan a bit slower.

18 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

Your computer then recognizes that a scanner has been plugged into
the USB port and automatically loads the appropriate software to
run the scanner.

The scanner’s status light is green when the scanner and computer
are communicating properly.

Do not proceed until you receive a message that your computer has
found the new hardware, or updated the driver database. If your
computer is running Windows XP, you will see the following message.

4. When you’re certain that the software has completely loaded, return

to the “Complete the installation by connecting your hardware”
window.

5. Click OK.

STEP 4: CONNECT THE USB CABLE AND TURN ON THE POWER 19

6. Click Close on the Installation Complete window to close and exit

the software installer.

If you selected OmniPage Pro for installation, a window tells you to
insert the second CD to install it.

Note: OmniPage Pro is required for your scanner to have its full range
of features. Please make sure to install OmniPage Pro before scanning.

20 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

To i n s t a l l O m n i Pa g e P r o :

1. Click Exit Disc 1 and remove Disc 1 from the CD-ROM drive.

2. Insert Disc 2 into the CD-ROM drive.

The OmniPage Pro Installation menu opens automatically. If it
does not open, see the note on page 9.

3. Select Install OmniPage Pro.

4. Follow the instructions on the screen to install OmniPage Pro.

5. When installation is finished, remove Disc 2 and store it in a safe

place.

6. If you want to install other software from Disc 1, re-insert it into

the CD-ROM drive now and see the next section, “Additional
Applications for Your Scanner.”

STEP 4: CONNECT THE USB CABLE AND TURN ON THE POWER 21

ADDITIONAL APPLICATIONS FOR YOUR SCANNER

Your scanner includes free, additional applications on the
installation CD.

Note: Some of the software
listed in this window may
not be available when you
purchase your scanner.

Please visit our web site at:
www.visioneer.com
for the latest updates.

To install the additional applications:

1. Return to the Installation window and select the additional

applications you want to install on your computer.

2. Click Install Now.

3. Follow the instructions on the installation windows.

®

If you want to install the Kofax VRS

software, you may see the

following message.

Please disregard this message and click OK. The Kofax VRS
Certified ISIS

®

driver is installed correctly when you install your

Visioneer Patriot 780 scanner driver and ISIS is one of the options.

22 VISIONEER PATRIOT 780 SCANNER USER’S GUIDE

4. When installation is finished, return to the Installation window and

click Main Menu.

5. On the Main Menu, click User Guides.

STEP 4: CONNECT THE USB CABLE AND TURN ON THE POWER 23

The Visioneer User Guides window opens. Use this window to view
and save the User Guides you want.

The User Guides are in Adobe
also includes a free copy of Acrobat

®

Acrobat® PDF format. The CD

®

Reader® in case your
computer does not have it already installed. The Scanner Readme
file is in HTML format and will open in any standard browser.

If you need to, click Acrobat Reader to install it now. Follow the
instructions on the installation windows.

To view and save the User Guides:

1. Click the name of a User Guide you want to view and it will open
in Acrobat Reader. Use the Acrobat Reader Save command to save
that User Guide on your computer.

2. Return to the Visioneer User Guides window and repeat the process
to open, view, and save all the other User Guides you want. The

Scanner Readme file has late-breaking news about your scanner.

3. When you’re finished, click Main Menu to return to the main
Visioneer Installation window and click Exit.

4. Remove the CD and store both CD’s in a safe place.

That’s it! Installation is finished and your Visioneer Patriot 780 scanner is
ready to scan.