Visioneer OneTouch 9650 User Manual

Visioneer® OneTouch®
9650 USB Scanner
User's Guide

for Windows

Visioneer OneTouch

9650 USB Scanner

User’s Guide

FOR WINDOWS

®

COPYRIGHT INFORMATION

Copyright © 2006 Visioneer, Inc.

Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws.

The Visioneer brand name and logo are registered trademarks of Visioneer, Inc. The PaperPort brand name and logo are registered trademarks of Nuance
Communications, Inc. Adobe®, Adobe® Acrobat®, Acrobat® Reader®, and the Adobe® Acrobat® PDF® logo are registered trademarks of Adobe Systems
Incorporated in the United States and/or other countries. The Adobe PDF logo will appear in this product’s software, and full access to Adobe software features
is only available if any Adobe product is installed on your computer.

This product is covered by one or more of the following patents: 6, 480, 304; 5,818,976; 5,499,108; 5,517,332.
Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation. ZyINDEX is a registered trademark of

ZyLAB International, Inc. ZyINDEX toolkit portions, Copyright © 1990-1998, ZyLAB International, Inc. All Rights Reserved. All other products mentioned
herein may be trademarks of their respective companies.

Information is subject to change without notice and does not represent a commitment on the part of Visioneer. The software described is furnished under a
licensing agreement. The software may be used or copied only in accordance with the terms of such an agreement. It is against the law to copy the software on
any medium except as specifically allowed in the licensing agreement. No part of this document may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying, recording, or information storage and retrieval systems, or translated to another language, for any
purpose other than the licensee's personal use and as specifically allowed in the licensing agreement, without the express written permission of Visioneer.

Part Number: 05-0486-600

Restricted Rights Legend

Use, duplication, or disclosure is subject to restrictions as set forth in contract subdivision (c)(1)(ii) of the Rights in Technical Data and Computer Software
Clause 52.227-FAR14. Material scanned by this product may be protected by governmental laws and other regulations, such as copyright laws. The customer
is solely responsible for complying with all such laws and regulations.

Visioneer's Limited Product Warranty

IF YOU FIND PHYSICAL DEFECTS IN THE MATERIALS OR THE WORKMANSHIP USED IN MAKING THE PRODUCT DESCRIBED IN
THIS DOCUMENT, VISIONEER WILL REPAIR, OR AT ITS OPTION, REPLACE THE PRODUCT AT NO CHARGE TO YOU, PROVIDED YOU
RETURN IT (POSTAGE PREPAID, WITH PROOF OF YOUR PURCHASE FROM THE ORIGINAL RESELLER) DURING THE 90-DAY PERIOD
AFTER THE DATE OF YOUR ORIGINAL PURCHASE OF THE PRODUCT. UPON RECEIPT DURING THE INITIAL 90-PERIOD BY
VISIONEER OF A VALID REGISTRATION OF THE PRODUCT, THIS LIMITED PRODUCT WARRANTY PERIOD IS EXTENDED TO THE
12-MONTH PERIOD AFTER THE DATE OF YOUR ORIGINAL PURCHASE. IF A VALID REGISTRATION IS NOT RECEIVED DURING THE
INITIAL 90-DAY PERIOD, THE 12-MONTH WARRANTY IS NO LONGER AVAILABLE AND YOUR PRODUCT WARRANTY WILL
TERMINATE AFTER THE 90-DAY INITIAL PERIOD EXPIRES.

THIS IS VISIONEER'S ONLY WARRANTY AND YOUR EXCLUSIVE REMEDY CONCERNING THE PRODUCT, ALL OTHER
REPRESENTATIONS, WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, WRITTEN OR ORAL, INCLUDING ANY WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE EXPRESSLY EXCLUDED. AS A RESULT,
EXCEPT AS SET OUT ABOVE, THE PRODUCT IS SOLD “AS IS” AND YOU ARE ASSUMING THE ENTIRE RISK AS TO THE PRODUCT'S
SUITABILITY TO YOUR NEEDS, ITS QUALITY AND ITS PERFORMANCE.

IN NO EVENT WILL VISIONEER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM ANY DEFECT IN THE PRODUCT OR FROM ITS USE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

All exclusions and limitations in this warranty are made only to the extent permitted by applicable law and shall be of no effect to the extent in conflict with the
express requirements of applicable law.

RoHS and WEEE Compliance

This product is compliant with RoHS Regulations of the European Parliament and Council Directive on the Restrictions of the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment (2002/95/EC), and with the Waste Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC).

FCC Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for the class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and if not installed, and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with
FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in
interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer
could void the user's authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.

TABLE OF CONTENTS i

TABLE OF CONTENTS

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

The Visioneer 9650 Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1: Assemble the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 2: Install the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 3: Connect the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Step 4: Connect the USB Cable and Turn on the Power . . . . . . . . . 17

View the User Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Register Your Scanner and Check for Updates . . . . . . . . . . . . . . . . . 23

Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Loading Documents to Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Scan From the OneTouch Button Panel . . . . . . . . . . . . . . . . . . . . . 27

Using the OneTouch Button Panel . . . . . . . . . . . . . . . . . . . . . . . . . 29

The Default OneTouch Settings on Your Scanner . . . . . . . . . . 33

Configuring the OneTouch Buttons . . . . . . . . . . . . . . . . . . . . . . . . 34

About the OneTouch Properties Window . . . . . . . . . . . . . . . . . 35

Selecting New Settings for a Button . . . . . . . . . . . . . . . . . . . . . 38

Setting Destination Application Properties . . . . . . . . . . . . . . . . 40

Selecting Page Format Options . . . . . . . . . . . . . . . . . . . . . . . . . 49

Scanning with Optical Character Recognition (OCR) . . . . . . . . 53

Renaming a OneTouch Button . . . . . . . . . . . . . . . . . . . . . . . . . 55

Selecting Options for a Button . . . . . . . . . . . . . . . . . . . . . . . . . 56

Creating a New Scan Configuration . . . . . . . . . . . . . . . . . . . . . 60

Editing or Deleting Scan Configurations . . . . . . . . . . . . . . . . . . 75

ii TABLE OF CONTENTS

Configuring Before Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Scan and Burn to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Scanning with Event Forwarding . . . . . . . . . . . . . . . . . . . . . . . . 80

Creating an HTML Web Page from Your Scanned Documents 83

Transferring Scanned Documents to Storage . . . . . . . . . . . . . . . 85

Checking the Hardware and Setting the Lamp Power Saving . . 89

Scanning with the TWAIN Interface . . . . . . . . . . . . . . . . . . . . . . . 92

Getting Help with the PaperPort Software . . . . . . . . . . . . . . . . 92

Accessing the TWAIN Interface from PaperPort . . . . . . . . . . . . . . . 93

The Two TWAIN Interface Options . . . . . . . . . . . . . . . . . . . . . . . . 96

Scanning from the TWAIN Basic Interface . . . . . . . . . . . . . . . . . . . 97

Scanning Part of an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Scanning from the TWAIN Advanced Interface . . . . . . . . . . . . . . 100

Adjusting the Image on the Advanced Interface . . . . . . . . . . . . 103

Adjusting the Brightness and Contrast . . . . . . . . . . . . . . . . . . . 107

Adjusting Gamma, Saturation, and Color Hue . . . . . . . . . . . . 108

Adjusting Input Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Creating a New Advanced Interface Profile . . . . . . . . . . . . . . . 112

Display the Device Configuration . . . . . . . . . . . . . . . . . . . . . . 113

Setting Up PaperPort to Work with Your Scanner . . . . . . . . . . . . . 114

Scanning with the WIA Interface. . . . . . . . . . . . . . . . . . . . . . . . . 119

Fine Tuning Your Scans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Scanning with the ISIS Interface . . . . . . . . . . . . . . . . . . . . . . . . . 127

Adjusting the ISIS Scan Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Scanning from ISIS in Other Applications . . . . . . . . . . . . . . . . . . . 134

TABLE OF CONTENTS iii

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Cleaning the Scanner Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Cleaning the Automatic Document Feeder . . . . . . . . . . . . . . . 136

Replacing the ADF Pad Assembly . . . . . . . . . . . . . . . . . . . . . . 137

Replacing the Roller Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 138

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Status Light Troubleshooting Codes . . . . . . . . . . . . . . . . . . . . 142

How to Uninstall Your Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Step 1: Uninstalling the OneTouch 4.0 Scanner Software . . . . 143

Step 2: Uninstalling the PaperPort Software . . . . . . . . . . . . . . 143

To Install Another Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Visioneer 9650 Scanner Specifications . . . . . . . . . . . . . . . . . . . . . . 145

Visioneer 9650 Scanner Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 146

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

iv TABLE OF CONTENTS

WELCOME

Your new Visioneer 9650 scanner can scan stacks of items or a single
page at a time, and place their images on your computer.

War ni ng: Do not plug in the USB cable until after you have
installed the software. Carefully follow the steps and sequence
described in the installation procedure beginning on page 6.

WHAT’S IN THE BOX

Before starting the assembly and installation, check the contents of the
box to make sure that all parts are included. If any items are missing or
damaged, contact the dealer where you purchased the scanner.

Visioneer 9650 Scanner Power cableUSB cable

Paper Guide Paper Guide Extension

Replacement ADF Pad

Installation CD

VISIONEER 9650 SCANNER USER’S GUIDE 1

Paper Stop

Power supply

Quick Install Card, and
Technical Support Card

2 VISIONEER 9650 SCANNER USER’S GUIDE

THE VISIONEER 9650 SCANNER

Document Cover

Document Pad

Glass

Reference Frame

Paper Stop

Paper Guide Extension

Paper Guide

Automatic Document Feeder

Lock (on underside of scanner)

Status Lights

USB Port

ADF port

Power jack

Power On/Off Switch

ADF Cable

THE VISIONEER 9650 SCANNER 3

Document Cover—Protects the document from light and contamination during scanning.

Document Pad—Helps to secure the document in place on the scanner glass.

Reference Frame—Place items face down within this frame. Markings on the border of the

frame show where to align various paper sizes.

Glass—Place items face down aligned at the upper left corner of the glass.

Paper Stop—Holds items in place as they are ejected from the Automatic Document Feeder.

Adjust the stop for either letter-sized or legal-sized pages.

Paper Guide Extension—Unfolds to support multiple pages to scan.

Paper Guide—Holds pages in place. Adjust to fit the size of the paper to scan.

Automatic Document Feeder (ADF)—Feeds a stack of pages onto the glass for scanning.

The ADF can hold up to 50 pages at a time.

Lock—Locks or unlocks the scanning head; located on the underside of the scanner.

Status Lights—Shows the scanner’s status. Blinking Green Ready light: scanner is preparing

itself or the lamp is warming up. Steady Green Ready light: the scanner is on and ready to
scan. Blinking Check light: the hardware is not ready to scan; see “Troubleshooting” on
page 140 for additional details.

USB Port—Connects the scanner to the computer.

ADF Port—Connects the ADF cable from the Automatic Document Feeder to the scanner.

Power Jack—Connects the power cord to the scanner.

Power On/Off Switch—Turns the scanner’s power on and off.

ADF Cable—Connects the ADF to the scanner body. The cable provides power to the ADF

and must be plugged in for it to operate.

4 VISIONEER 9650 SCANNER USER’S GUIDE

WHAT YOU NEED

An IBM-compatible Pentium PC, or AMD equivalent with:

■ A CD-ROM drive

■ An available Universal Serial Bus (USB) port; 1.1 or 2.0

■ Microsoft Windows XP (Service Pack 1 or 2) or

Windows 2000 (Service Pack 4)

■ A minimum of 512 MB (megabytes) of internal memory (RAM)

■ 200 MB minimum of free hard disk space

A VGA or SVGA Monitor

The recommended settings for your monitor are:

■ High Color (16-bit) or True Color (24-bit or 32-bit)

■ Resolution set to at least 800 x 600 pixels

To set your monitor’s colors and resolution:

■ Open the Windows Control Panel

■ Double-click on Display then select the Settings tab.

DOCUMENTATION

The following documentation is provided with your scanner:

■ Quick Install Card—Abbreviated installation instructions.

■ Visioneer 9650 Scanner User’s Guide—On the Installation CD;

contains detailed installation, scanning, configuration, and
maintenance information.

■ Online Help—For the scanner configuration, TWAIN and WIA

interfaces, and PaperPort software application.

BEFORE YOU BEGIN 5

Installing

War ni ng: Do not plug in the USB cable until after you have
installed the software. Complete the installation steps in the order
described in the installation procedure below.

Installation is a quick, four-step process:

1. Assemble the scanner

2. Install the software

3. Connect the power supply

4. Connect the USB cable and turn on the power

BEFORE YOU BEGIN

Please make sure of the following before you begin installation:

■ If your computer has AntiVirus or AntiSpyware software running,

you may encounter alerts or messages during installation asking
you to allow the installation to proceed. Although the messages will
differ based on the software your computer is running, in each case
you should allow the installation to proceed if that option is
available. Alternatively, you can turn off the AntiVirus or
AntiSpyware software before installing your scanner. But if you do,
make sure to turn it back on again when installation is finished.

■ If you already have a scanner connected to your computer, you may

need to remove its driver programs first before beginning the
installation of your Visioneer 9650 USB scanner. Please see “How
to Uninstall Your Scanner” on page 143 for basic instructions, or
see the User’s Guide that you received with your other scanner.

6 VISIONEER 9650 SCANNER USER’S GUIDE

STEP 1: ASSEMBLE THE SCANNER

All the components to assemble the scanner are included in the box.

To assemble the scanner:

1. Remove all shipping tape from the top and bottom of the scanner.

2. Slide the locking tab on the bottom of the scanner to its unlocked
position.

Unlocked position

Note: The locking tab protects the scanner’s scan head by holding it
securely in position. Lock the scanner when transporting it from one
location to another, but always remember to unlock it before
scanning. The scanner will not scan when locked.

STEP 1: ASSEMBLE THE SCANNER 7

3. Insert the slots (A) on the Paper Guide onto their tabs (B) on the
scanner and slide the Guide down into place. The catch tabs (C)
“snap” into place. Refer to the picture on page 2 to see the location
of the assembled parts.

A

B

C

4. Insert the Paper Guide Extension into the Paper Guide and “snap”
its tabs into place.

8 VISIONEER 9650 SCANNER USER’S GUIDE

5. Insert the Paper Stop onto the back of the scanner and slide it
downward to “snap” its tabs into place.

6. Plug the ADF cable into the ADF port on the body of the scanner.
Make sure the cable is plugged in securely. The ADF will not work
if the cable is loose or not plugged in.

7. Proceed to “Step 2: Install the Software.”

STEP 2: INSTALL THE SOFTWARE 9

STEP 2: INSTALL THE SOFTWARE

The Installation CD contains all the driver software and scanning
software to run your scanner.

To install the software:

1. Start Microsoft Windows and make sure that no other applications
are running.

2. Insert the Installation CD into your computer’s CD-ROM drive.

Note: If the CD does not automatically start, check the following:

■ Make sure the CD drive’s door is completely shut.

■ Make sure the CD was inserted in the drive in the proper direction

(label side up).

To launch the CD manually.

■ Open the Windows option for My Computer. You can do this by

double-clicking on the My Computer icon on your desktop.

■ Double-click the icon for your CD-ROM drive.

■ The Installation menu for the CD should now open.

If the menu does not open:

■ From the list of files on the CD, double-click the file named

START32.EXE.

10 VISIONEER 9650 SCANNER USER’S GUIDE

When the CD starts, the Visioneer Installation window opens
automatically.

3. On the Installation Main Menu, click Install Products.

The next window lists the software that is available to install on
your computer.

4. Select Nuance® PaperPort®, Scanner Driver, and QuickScan®.

5. Click Install Now. The PaperPort software will load first.

STEP 2: INSTALL THE SOFTWARE 11

6. The Select Language window opens for the PaperPort software.
Click the drop-down menu arrow and select the language you want
to use. Click OK.

The first PaperPort Installation window opens.

7. On the PaperPort Welcome window, click Next.

Installing PaperPort will uninstall any existing version of PaperPort
and will install the newer version while retaining all of your
previous PaperPort files.

8. Read the PaperPort license agreement and select I accept the terms
in this agreement, then click on Next. If you choose not to accept
the license agreement, the installation will terminate and the
PaperPort software will not be installed.

9. On the Customer Information window, accept the current values or
enter new information, then click Next.

10. On the Setup Type window, keep the default Setup Type and click
Next.

11. Click Install to begin the installation.

Reminder: If your computer is running an AntiVirus or
AntiSpyware application, you may see messages asking you to allow
installation. Select the option to allow installation to proceed with
the install.

12. On the Product Registration window, do one of the following:

■ Select Register online, click OK, then follow the registration

instructions.

■ Select Print registration form, click OK, then follow the

instructions to complete and print the registration form.

■ Select Remind me in 7 days and click OK.

13. At the InstallShield Wizard Completed window, click Finish.

If a message window opens instructing you to restart your
computer, click Restart.

12 VISIONEER 9650 SCANNER USER’S GUIDE

14. When installation of PaperPort is finished, the Welcome to the
OneTouch 4.0 Setup Wizard opens.

15. Click Next.

16. On the Visioneer License Agreement window, read the license
agreement. If you accept the terms, select I Agree, and click Next.

If you choose not to accept the license agreement, the installation
will terminate and the scanner driver will not be installed.

17. Click Next.

The next window lists the choices of the drivers that you can install
for your scanner.

STEP 2: INSTALL THE SOFTWARE 13

18. Select the option you want.

■ Full Install (OneTouch, TWAIN and ISIS)—This is the

recommended installation. It installs the OneTouch 4.0 software
which provides the necessary driver software for the scanner. It also
installs scanning interfaces for TWAIN, Microsoft’s Windows
Image Acquisition (WIA), and the ISIS driver. Installing this
option means that you can use several different methods to scan, as
explained in this User Guide.

■ TWAIN and ISIS—The TWAIN and ISIS drivers are installed.

The OneTouch 4.0 Monitor will not run and you cannot use the
OneTouch features. You can use the TWAIN driver to scan from
other TWAIN applications, and from WIA on Windows XP
computers. You can also scan from applications that use the ISIS
driver.

■ TWAIN only—Only the TWAIN driver is installed. You will only

have access to the Visioneer 9650 TWAIN driver and WIA
(Windows XP only). You will not be able to use the OneTouch 4.0
software.

14 VISIONEER 9650 SCANNER USER’S GUIDE

■ ISIS only—The ISIS driver is installed. You can use applications

that use the ISIS driver to scan. You can use WIA to scan if your
computer is running Windows XP. You will not be able to use the
TWAIN driver or OneTouch to scan.

Note: If you decide to change your scanner’s installed drivers later
on, you must first uninstall the drivers the scanner is currently using.
See the section “To Install Another Driver” on page 144.

19. Click Next.

During installation you will see this window asking you to select
one of the images for your Color Space setting.

20. Select the option that looks best to you and click Next.

The Color Space setting sets the gamma value for the scanner so
scanned items look good on your monitor. Gamma controls the
brightness of the midtones of colors. That setting can be changed
later on as you’re scanning.

The driver installation will now begin.

STEP 2: INSTALL THE SOFTWARE 15

21. STOP when you see this Installation Complete window. Do NOT
click Finish yet. Leave the window open and proceed to the next
section,“Step 3: Connect the Power Supply.”

Reminder: If your computer is running AntiVirus or AntiSpyware
software, you may see messages asking you to allow installation. Select
the option to allow installation to proceed.

Note: If you want to see more information about your scanner and a
quick explanation of how to use the OneTouch features, click the
More button on the window. When you’re finished, return to the
window above to continue with the installation process.

16 VISIONEER 9650 SCANNER USER’S GUIDE

STEP 3: CONNECT THE POWER SUPPLY

Connect the power supply and power cord, and plug the power supply
into an electrical outlet.

To connect the power supply:

1. Plug the power supply into its power port on the scanner.

Make sure the ADF cable is plugged in securely. If the cable is loose
the ADF will not function properly.

Note: Only use the power supply (HEG42-240100-7L made by
HiTRON) included with your scanner. Connecting any other type of
power supply may damage your scanner and will void its warranty.

2. Plug the power cord into the power supply and into a wall outlet.

Now proceed to the next section, “Step 4: Connect the USB Cable
and Turn on the Power.”

STEP 4: CONNECT THE USB CABLE AND TURN ON THE POWER 17

STEP 4: CONNECT THE USB CABLE AND TURN ON THE

OWER

P

Your Visioneer 9650 scanner connects to any available USB port. Check
your computer’s manual for the USB port locations.

Note: You can connect the scanner to your computer while the
computer is running. You do not have to shut down your computer.

1. Remove any protective tape from the USB cable.

2. Plug the USB cable into the USB port on the scanner then into a
USB port on the computer. Connection to a USB 2.0 High Speed
port provides optimum performance, however your scanner will
also connect to a USB 1.1 port.

The USB symbol, as seen in the above diagram, identifies the
location of the USB port on your computer. If the plug does not
attach easily, make sure that you are plugging it in correctly. Do not
force the plug into the connection.

You can also connect the scanner to a USB port on the computer’s
keyboard if it has one, or to a USB hub. If you use a USB hub, it
must have its own power supply already plugged into an electrical
outlet.

18 VISIONEER 9650 SCANNER USER’S GUIDE

Note: If you have not installed the scanner driver, unplug the USB
cable from the computer and install the software now. When the
driver installation is complete, a message tells you when to connect
the scanner.

3. Turn on the power switch, located on the back of the scanner.

The status light comes on and flashes indicating that the scanner is
receiving power.

If you are using Windows XP Service Pack 2, and have plugged the
USB cable into a USB 1.1 port, an information bubble may open
explaining that “A HI-SPEED USB device is plugged into a non­HI-SPEED USB hub”. Plug the USB cable into a USB 2.0 port (if
available) or just disregard the message. If you leave it plugged into
the USB 1.1 port, your scanner may scan a bit slower.

STEP 4: CONNECT THE USB CABLE AND TURN ON THE POWER 19

4. Your computer recognizes that a scanner is plugged into the USB
port and automatically loads the appropriate driver software to run
the scanner.

Do not proceed until you receive a message that your computer has
found the new hardware, or updated the driver database. If your
computer is running Windows XP, you will see the following message.

5. When you’re certain that the software has completely loaded, return
to the “Complete the installation by connecting your hardware”
window.

Note: To see more information about your scanner, click the More
button on the window. When you’re finished, return to the window
above to continue with the installation process.

20 VISIONEER 9650 SCANNER USER’S GUIDE

6. Click OK.

7. Click Close on the Installation Complete window to close and exit
the software installer.

8. When the window appears for installing the QuickScan software,
click Next and follow the instructions on the screen.

VIEW THE USER GUIDES 21

VIEW THE USER GUIDES

The User’s Guides for your Visioneer 9650 scanner, and for the
PaperPort software are also on the Installation CD.

To view the user’s guides:

1. Return to the Installation window and click User Guides.

The Visioneer User Guides window opens. Use this window to view
and save the User Guides you want.

22 VISIONEER 9650 SCANNER USER’S GUIDE

The User Guides are in Adobe® Acrobat® PDF format. The CD

also includes a free copy of Acrobat
computer does not have it already installed. The Scanner Readme
file is in HTML format and will open in any standard browser.

If you need to, click Acrobat Reader to install it now. Follow the
instructions on the installation windows.

To view and save the User Guides:

1. Click the name of a User Guide you want to view and it will open
in Acrobat Reader. Use the Acrobat Reader Save command to save
that User Guide on your computer.

2. Return to the Visioneer User Guides window and repeat the process
to open, view, and save the other User Guides you want. The

Scanner Readme file has late-breaking news about your scanner.

®

Reader® in case your

3. When you’re finished, click Main Menu to return to the main
Visioneer Installation window and click Exit.

That’s it! Installation is finished and your Visioneer 9650 scanner is ready to
scan.

REGISTER YOUR SCANNER AND CHECK FOR UPDATES 23

REGISTER YOUR SCANNER AND CHECK FOR UPDATES

Registering your scanner is important as it provides you with access to
our free telephone support service. Registration also gives you free access
to software updates for your scanner.

To register your scanner:

The OneTouch Icon.

1. Right-click on the OneTouch icon in the Windows Notification
Area (at the bottom right corner of the screen).

2. Choose Check for Online Updates from the pop-up menu.

3. Follow the instructions on the screen and register your scanner by
entering your scanner’s serial number and your email address.

Note: A valid email address is required.

The serial number is located on the side of the scanner.

4. After receiving your RegID, write it down on a piece of paper and

The Serial Number

After registration is complete you will receive an email message with
your RegID. Your RegID is important as you will need it when
accessing free telephone support, or checking for online updates.

keep it with your scanner so you will be able to find it easily.