Vision ZS 5101 EU, ZS 5101 US, ZS 5101 BR, ZS 5101 JP, ZS 5101 IN Installation & Operation Manual

7. NoExternal Switch: If you need to add external switch function, please connect with

ZS5101 for extending detection. The ZS5101 has 2 normally closed contact
terminals. These can be used for additional external switch wired contacts. The
external switch will send an alarm report (type: 07, level: 0xFF) by opening the
window/door.

Operation

1. Vibrate the ZS 5101, sensor will send status of “ON”(Basic Set,Value:0xFF) & alarm
report (type:07, level:0Xff) to any associated nodes. With no triggered in 10
seconds, the senor will send status of “OFF”(Basic Set,Value:0x00) & alarm report
(type:07, level:0x00)

2. Normal operation, the LED will not light.

3. The ZS 5101 sensor equipped with tamper switch. If the cover of sensor is removed,

the ZS 5101 will send an alarm report (type:07,level:0xFF) to the Z-Wave™
Interface Controller, and the LED will go solid.

Federal Communications Commission Statement

This equipment has been followed to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
and correct the interferene by one of the following measures:
Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiver,
Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undersired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.

Limited Warranty

Vision Guarantees that every wireless shock sensor is free from physical defects in material and
workmanship under normal use for one year from the date of purchase. If the product proves
defective during this one-year warranty period, Vision will replace it free of charge. Vision does not
issue any refunds. This warranty is extended to the original end user purchase only and is not
transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or
abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair,
taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages
exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost, or
reinstallation cost.

For information on addional devices, plesae visit us at www.visionsecurity.com.tw

-3-

Installation & Operation Manual

ZS 5101 EU
ZS 5101 US
ZS 5101 BR
ZS 5101 JP
ZS 5101 IN

Wireless Shock Sensor

ZS 5101

V0

1011123

6B1Z-51001

Introduction

Thanks for choosing the Vision’s wireless shock sensor of the home security device. This
sensor is a Z-Wave™ enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave™ enabled network. Every mains
powered Z-Wave enabled device acts as a signal repeater and multiple devices result in
more possible transmission routes which helps eliminate “RF dead-sports”
Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer’s
Z-Wave™ enabled networks. This sensor detects the vibrations made by an intruder
trying to break a window or door, and also detect tamper situations, it will send Z-Wave™
signal when vibrations or tamper situations are detected.

Product Description and Specification

*** For indoor use only ***

Specification:

Package Content

Protocol: Z-Wave™ (ZM3102N)
Frequency Range:

868.42MHz (ZS5101EU)

908.42MHz (ZS5101US)

921.42MHz (ZS5101BR)

920.00MHz (ZS5101JP)

865.22MHz (ZS5101IN)

Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F~140°F)
Battery: Panasonic CR123A * 1PC

1pc ZS 5101 Shock sensor
1pc Bracket Holder
1pc Adhesive tape for sensor
3pc Screw
1pc CR123A Lithium Battery
1pc Installation & Operation

Manual

Z-Wave Command Classes:
COMMAND_CLASS_BASIC
COMMAND_CLASS_ALARM_V2
COMMAND_CLASS_ASSOCIATION_V2 (_V1 JP only)
COMMAND_CLASS_BATTERY
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_SENSOR_BINARY
COMMAND_CLASS_VERSION
COMMAND_CLASS_WAKE_UP_V2

Installation

Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to
the installation guide of Z-Wave™ Interface Controller before installing ZS 5101 Shock
Sensor.

1. Install Battery: Use care when installing the battery. Press the locking tab on the top sensor

cover, and then gently pull up the cover. Observe the correct polarity before insert the
battery.

2. After insert the battery, the LED will start to flash slowly, which means the sensor
has not yet been “inclusion”.

3. For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller
into “inclusion” mode, and following its instruction to add the ZS 5101 to your
controller. To get in the “inclusion” mode, the distance between sensor and

controller is suggested to be in one meter. Press the program switch of ZS 5101
for 1 second at least to be included. The LED on the ZS 5101 should go off, if not,
please try again.

For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface
Controller into “exclusion” mode, and following its instruction to delete the ZS 5101
from your controller. Press the program switch of ZS 5101 for 1 second at least to
be excluded.

For “Association” :removing the cover of the ZS 5101 to get into the “Awake”
mode, then put the Z-Wave™ Interface Controller into “Association”, and following
its instruction to associate the ZS 5101 with other device. Close the cover back after
“association” done, afterward the ZS 5101 will get into “Sleep” mode for power
saving. Support one association group (5 nodes).

|

”Awake” mode: it is to leave the “Sleep” mode by removing the cover of ZD5101,
to allow the Z-Wave™ Interface Controller to do “Inclusion”, “Exclusion”,

“Association” and to reply and receive the commands from controller.

4. Slide back the rear cover and screw fastening with the front cover, the LED should
go off.

5. Using the adhesive tape or fixing screws to fix the bracket holder with shock sensor.

6. Sensitivity Adjustment:

To increase sensitivity, turn the adjustment clockwise.
To decrease sensitivity, turn the adjustment counter-clockwise.

-2-

-1-