Vision VE810 S5, Express S5 Installation Manual

Page 1
Vision VE810 Engraver S5
Installation Guide
© 2018 Vision Engraving & Routing Systems
Revised: 11/5/2018Part number 12-1085-01
Page 2
Vision VE810 Engraver S5 Installation Guide
© 2018 Vision Engraving & Routing Systems
All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher.
While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document.
Revised: 11/5/2018
Page 3
Table of Contents
3Contents
Part I
Part II
Part III
Introduction
................................................................................................................................... 51 Computer Requirements
................................................................................................................................... 62 General Electrical and Facility Requirements
................................................................................................................................... 63 VE810 Engraver Installation Layout
Vision Software Installation Machine Setup
................................................................................................................................... 211 Direct Connection to Computer
................................................................................................................................... 272 Network Connection
4
7
18
© 2018 Vision Engraving & Routing Systems
3
Page 4
Vision VE810 Engraver S5 Installation Guide4
1 Introduction
This guide contains information to prepare the new owner of a Vision Express for the proper installation of their machine. It is the customer's responsibility to read through this guide and make sure the work area, electrical and computer requirements are met. If for any reason, there are questions about these requirements, please call your Vision representative as soon as possible.
In the following sections, the complete machine and Vision software installation will be outlined. Please call your distributor or the service department at Vision for assistance if you have any questions
with this procedure. FOR MORE DETAILED INFORMATION, PLEASE REFER TO THE USER GUIDE FOR YOUR MACHINE
INSTALLED WITH THE VISION SOFTWARE. USER GUIDES ARE ALSO AVAILABLE ONLINE AT
http://www.visionengravers.com/support/vision-engraver-manuals.html
Important Note:
The Vision software is available in two versions; one with a dongle, and one that is " dongle-less" and is loaded on to a USB Memory stick. If your machine was delivered with, or you currently have the white/blue or orange software dongle, DO NOT LOSE IT! The Vision software will NOT run without the dongle plugged into the computer.
© 2018 Vision Engraving & Routing Systems
Page 5
1.1 Computer Requirements
Minimum System
Requirements:
CPU:
Dual Core (2.0GHz or higher)
Hard Drive:
750 GB free space
RAM:
1GB + OS Requirements
Operating System:
Windows 10 (32/64 bit) Windows 8 (32/64 bit) Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1
Ports:
USB port for security dongle Local or network Ethernet port to connect machine
Suggested System
Requirements
CPU:
Core i3 (or faster)
Hard Drive:
1 TB (or more)
RAM::
4GB + OS Requirements
Operating System:
Windows 10 (32/64 bit) Windows 8 (32/64 bit) Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1
Ports
USB port for security dongle Local or network Ethernet port to connect machine
Introduction 5
© 2018 Vision Engraving & Routing Systems
Page 6
Vision VE810 Engraver S5 Installation Guide6
Machine Model
Requirements
VE810
One 110 VAC 15 Amp or One 220 VAC 10 Amp Single Phase
Optional Equipment
Engraving Vacuum Chip Removal System
One 110 VAC 15 Amp
1.2 General Electrical and Facility Requirements
NOTE: In addition to the above requirements, a standard outlet is required for the computer.
1.3 VE810 Engraver Installation Layout
VE810 Layout Diagram
© 2018 Vision Engraving & Routing Systems
Page 7
2 Vision Software Installation
Insert the Vision USB dongle into the USB port on the computer. Navigate to the Devices and Drives area on your PC. Double click on the Vision icon to open the files on the USB dongle.
Select the Start or Start.exe file to begin.
Introduction 7
Click on the Install Vision Software button.
© 2018 Vision Engraving & Routing Systems
Page 8
Vision VE810 Engraver S5 Installation Guide8
The Vision S5 Software Wizard will guide you through the process of installing the software. Press Next to continue.
Press Install to continue
© 2018 Vision Engraving & Routing Systems
Page 9
Setup wizard will install the program.
Select Finish to continue the software installation.
Vision Software Installation 9
Choose your preferred language and click ok.
© 2018 Vision Engraving & Routing Systems
Page 10
Vision VE810 Engraver S5 Installation Guide10
The Vision 10 Setup Screen will appear. Press Next.
After accepting the license agreement, click on the Next button.
© 2018 Vision Engraving & Routing Systems
Page 11
Vision Software Installation 11
Select Next (or change the destination folder - not recommended).
Select Next to create the folder.
© 2018 Vision Engraving & Routing Systems
Page 12
Vision VE810 Engraver S5 Installation Guide12
The installation will continue.
© 2018 Vision Engraving & Routing Systems
Page 13
Vision Software Installation 13
Select the VE810 S5 by placing a check mark in the box to the left of VE810 in the Manufacturer list, then select Next. If you purchase another engraving system from Vision, it can be added to the machine list at a later date from within the Vision software.
Select the VE810 S5. Note – The VE810 Vice/Center Origin S5 is used when using the center vice accessory.
© 2018 Vision Engraving & Routing Systems
Page 14
Vision VE810 Engraver S5 Installation Guide14
Select Continue to install True Type fonts and Vision Engraving Fonts on your computer.
© 2018 Vision Engraving & Routing Systems
Page 15
Click yes to install all additional fonts from your C:\ Drive.
Vision Software Installation 15
All system fonts will be installed.
© 2018 Vision Engraving & Routing Systems
Page 16
Vision VE810 Engraver S5 Installation Guide16
Press OK
Press on the Finish button.
© 2018 Vision Engraving & Routing Systems
Page 17
Press the Exit button .
Vision Software Installation 17
The Vision manuals icon should now appear on your computer's desktop along with an icon for your version of Vision 10 software.
© 2018 Vision Engraving & Routing Systems
Page 18
Vision VE810 Engraver S5 Installation Guide18
3 Machine Setup
On the rear of the VE810, there are four connection ports. The input power, the RJ-45 Ethernet port, the USB port and the remote vacuum chip removal system on/off port.
VE810 (rear view)
Connect the power supply cord to a 100 - 240 volt AC power source. Then plug the power cable into the port on the back of the machine. Plug one side of the network cable (black network cable) to the back of the machine and the other side to either the PC Ethernet port, a network switch box or a company network port.
NOTE: The Ethernet crossover cable is gray and should not be needed. If the emergency stop screen appears on the LCD when the machine is powered on, then the emergency
stop button is pressed in. Release the button twisting it until it "pops up". This will clear the emergency stop screen.
© 2018 Vision Engraving & Routing Systems
Page 19
Machine Setup 19
The VE810 IP address configuration setup will vary depending on how it is connected to the PC. The two options for connecting the VE810 to the computer are:
- Direct connection to the computer or direct connection using a network hub or switch. Both of these methods require the same setup.
- Connection through a company network
© 2018 Vision Engraving & Routing Systems
Page 20
Vision VE810 Engraver S5 Installation Guide20
Follow the steps from one of the two sections below to configure the IP address depending on the connection type above.
© 2018 Vision Engraving & Routing Systems
Page 21
3.1 Direct Connection to Computer
Direct connection to the computer or direct connection using a network hub or switch.
Machine Setup 21
Once the machine is connected directly to the computer's network port or is connected directly to a network hub or switch with the black Ethernet cable, power the machine on. The power switch for the VE810 is located on the power supply box for the machine. Once the machine has initialized, the home screen will appear on the LCD screen.
Select the Settings Screen icon.
© 2018 Vision Engraving & Routing Systems
Page 22
Vision VE810 Engraver S5 Installation Guide22
Select the Connectivity Screen icon.
Confirm that the LCD shows the Mode is set to static.
If the Mode displays DHCP, press the mode icon. This will change the Mode to display Static.
© 2018 Vision Engraving & Routing Systems
Page 23
Machine Setup 23
Confirm that the LCD shows the Address is set to 192.168.5.101.
If the Address is not set to 192.168.5.101, it will need to be changed. Press the tools icon.
Enter the numbers 192.168.5.101 with the numbers on the LCD. If you make a mistake, you can press the left arrow to erase a number.
Press the green check mark to accept the value.
The Mask value will be blank. Press the green check mark a second time and the mask will change to
255.255.255.0. If the Mask does not change to this value, enter it with the numbers on the LCD.
© 2018 Vision Engraving & Routing Systems
Page 24
Vision VE810 Engraver S5 Installation Guide24
The LCD should now look like below:
Press the X to exit the connection screen.
Press the X to return to the home screen. NOTE - This follow section is shown on a Windows 10 PC. For Windows 7 or Windows 8, the screens
are slightly different. The IP address of the computer IP address will need to be set to match the machines network settings. To set the computer's IP address, right click on the network icon in the lower right corner of the Windows
desktop screen.
Select "Open Network & Internet settings". (In Windows 7 and Windows 8 select "Open Network and Sharing Center")
© 2018 Vision Engraving & Routing Systems
Page 25
Machine Setup 25
Select "Change adaptor options". (In Windows 7 and Windows 8 select "Change adapter settings")
Right click on the Ethernet adapter shown and select "Properties".
© 2018 Vision Engraving & Routing Systems
Page 26
Vision VE810 Engraver S5 Installation Guide26
Select "Internet Protocol Version 4 (TCP/IPv5) and select "Properties".
Select "Use the following IP address:" and enter 192.168.5.100 for the IP address and enter
255.255.255.0 for the Subnet mask.
Select OK. The Windows network settings are the machine are now configured.
© 2018 Vision Engraving & Routing Systems
Page 27
3.2 Network Connection
Connecting through an office network
Once the machine is connected to the company network port, power the machine on. The power switch for the VE810 is located on the power supply box for the machine. Once the machine has initialized, the home screen will appear on the LCD screen.
Select the Settings Screen icon.
Machine Setup 27
Select the Connectivity Screen icon.
© 2018 Vision Engraving & Routing Systems
Page 28
Vision VE810 Engraver S5 Installation Guide28
Confirm that the LCD shows the Mode is set to DHCP.
If the Mode displays Static, press the mode icon. This will change the Mode to display DHCP. Make a note of the address that is displayed. This will be needed at a later step in the setup. NOTE: If
an IP address is not displayed, check with your network administrator to confirm that your network is configured for DHCP.
Press the green check mark button.
© 2018 Vision Engraving & Routing Systems
Page 29
Machine Setup 29
Press the X to exit the connection screen.
Press the X to return to the home screen.
Open the Vision 10 Software by selecting the Vision Expert 10, Vision Express 10 or Vision Pro 10 icon from the Windows desktop.
Go to the Engrave menu and select engraving defaults.
© 2018 Vision Engraving & Routing Systems
Page 30
Vision VE810 Engraver S5 Installation Guide30
In the Engraving defaults window select the setup button.
Select the port tab.
© 2018 Vision Engraving & Routing Systems
Page 31
Machine Setup 31
In the "IP address" box, enter the IP address that was displayed on the Vision Express in a previous step. You can see this address from the machine home screen by pressing settings icon and then the connectivity screen icon.
Verify that the method is set to "Use Production Spooler", the Port location is set to "TCIP raw", and the port is set to "22000".
IMPORTANT: If more than one driver is installed, you must change the IP address in the port tab for all drivers.
© 2018 Vision Engraving & Routing Systems
Page 32
Vision VE810 Engraver S5 Installation Guide32
Next, press Apply and OK to save the settings.
The machine and Vision software are now configured.
© 2018 Vision Engraving & Routing Systems
Page 33
Machine Setup 33
© 2018 Vision Engraving & Routing Systems
Page 34
Loading...