Page 1
1.
Precautions
• Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
• Please keep the manual in good condition for your future reference and service
application.
• Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
• If any liquid or solid matter gets into the housing, immediately disconnect the
camera from power supply and have it checked by your authorized dealer before
reusing.
• Avoid installing the camera at extremely hot or cold places.
• If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts
inside that need maintenance by the user. All maintenance should be carried out
by qualified personnel.
• Avoid installing the camera at a place of high humidity.
• Avoid installing the camera at the place exposed to gas or oil.
• Keep the top glass of the lens always clean in order to obtain the best picture
Hi-Resolution Indoor Dome Camera
VD-80PN / VD-80PNV
Quick Installation Guide
(IR version)
Page 2
Page 3
Hi-Res Indoor Dome
Camera
QUICK INSTALLATION
GUIDE
(IR version)
1.
Precautions
• Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
• Please keep the manual in good condition for your future reference and service
application.
• Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
• If any liquid or solid matter gets into the housing, immediately disconnect the
camera from power supply and have it checked by your authorized dealer before
reusing.
• Avoid installing the camera at extremely hot or cold places.
• If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts
inside that need maintenance by the user. All maintenance should be carried out
by qualified personnel.
• Avoid installing the camera at a place of high humidity.
• Avoid installing the camera at the place exposed to gas or oil.
• Keep the top glass of the lens always clean in order to obtain the best picture
Hi-Resolution Indoor Dome Camera
QUICK INSTALLATION GUIDE
+
Special features
● 1/3” HIGH RESOLUTION SUPER SENSITIVE
● 700TV Lines(Color) / 750TV
●
Demoire
● 2D DNR / Dead pixel
● Wide range of Auto White
● Smart IR (IR
version)
(IR version)
Lines(B/W)
compensation
Balance
CCD
*
OPTION
: Varifocal Lens
D-WDR
(2.8~12mm)
Page 4
1.
Precautions
• Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
• Please keep the manual in good condition for your future reference and service
application.
• Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
• If any liquid or solid matter gets into the housing, immediately disconnect the
camera from power supply and have it checked by your authorized dealer before
reusing.
• Avoid installing the camera at extremely hot or cold places.
• If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts
inside that need maintenance by the user. All maintenance should be carried out
by qualified personnel.
• Avoid installing the camera at a place of high humidity.
• Avoid installing the camera at the place exposed to gas or oil.
• Keep the top glass of the lens always clean in order to obtain the best picture
quality all the time. Be careful not to be stained by fingerprint.
• Don't face the camera directly toward sunlight or sunlight reflecting area.
The sensor may go defective at this condition.
• Please give a special attention to keep the unit from dangerous drop or external
shock during the process of transportation or handling.
• Never try to touch the camera
• Do not expose the camera to radioactivity. It causes a serious damage on the
sensor.
in wet hand. It may cause an electric shock.
Page 5
• Never try to touch the camera in wet hand. It may cause an electric shock.
• Do not expose the camera to radioactivity. It causes a serious damage on the
sensor.
2. Limitation of
liability
This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability, fitness
for any particular purpose, or non-infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes
are added to the information herein, at any time, for the improvements of
this publication and/or the corresponding product(s).
3. Disclaimer of
warranty
In no event shall seller be liable to any party or any person, except for
replacement or reasonable maintenance of the product, for the cases, including
but not limited to below:
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product;
(2) Personal injury or any damage caused by inappropriate use or negligent
operation of the user;
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any
reason or cause including any failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of
the system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that
surveillance-camera's picture, including saved data, for some reason, becomes
public or is used for the purpose other than surveillance.
Page 6
4.
Package
Camera x 1
Indoor Dome Camera
QUICK INSTALLATION GUIDE
Special features
●
1/3” HIGH RESOLUTION SUPER SENSITIVE C CD
650TV Lines(Color)/ 700TV Li nes(B/W)
●
●
Smart IR and De moi re
●
D-WDR
●
2D DNR / Dead pix el compens ation
●
Wide range of Auto W hite Balanc e
Manual x 1
Drilling template x 1
Tapping screws x 3
Plastic anchor x 3
Plastic Key x 1
Page 7
5.
Installation
5-1. How to open the dome
Plastic
Key
Insert supplied plastic key into the narrow flat hole on the dome body and
*
twist to open the dome cover.
5-2. Tool-free 3-Axis mounting mechanism
-Perfect 3-axis
▪ Panning axis up to 360° degree
▪ Tilting axis up to 90° degree
▪ Rotation axis up to 180° degree
a. Panning 360 degree
Turn the pan base right or left to
adjust the pan angle.
b. Tilting 90 degree
Loosen the tilt lever on the right or
left side of the camera board.
Control the camera tilt angle and
fasten the tilt lever again.
c. Rotation 180 degree
Tilt 90˚
The front side of the camera
Pan base
Pan 360˚
Tilt lever
Rotation 180˚
Grasp the front side of the camera board and turn it right or left to set the exact
angle of image.
Page 8
ModDeEl L
Hi-Res Indoor Dome Camera
Image Device
1/3" HIGH RESOLUTION SUPER SENSITIVE CCD
Effective Pixels
NTSC : 976(H)X494(V), PAL : 976(H)X582(V)
Scanning System
NTSC 525 Lines PAL 625 Lines 2:1 Interlaced
Synchronization
Internal
H.Resolution
700TV Lines(Color)/ 750TV Lines(B/W)
Min. illumination
0.1 lux / IR version (0 lux, 3 lux/IR ON)
Video OUT
1.0 Vp-p / 75 ohm
S/N Ratio
More than 50db
Gain Control
AUTO
LENS
3.6mm, 4.3mm, 6mm board Lens
2.8~12mm VF Auto DC iris Lens
Shutter speed
AUTO
White Balance
ATW (2,500°K ~ 10,000°K)
Day&Night
AUTO (COLOR, B/W)
DPC
Dead Pixel Compensation
Power Source
12VDC
Power Consumption
Board Type : 80mA
Board IR Type : 90mA(IR OFF) / 285mA(IR ON)
VF Type : 100mA
VF IR Type : 140mA(IR OFF) / 330mA(IR ON)
Viewable Distance
UP to 20M at Moonless Night
MTBF
20,000 hours
Operating Temp.
-10°C ~ 50°C
Storage Temp.
-20°C ~ 60°C
Measurement (mm)
114(Φ) x 90(H)
Weight (Approx.g)
Board Type : 160g / Board IR Type : 180g
VF Type : 185g / VF IR Type : 205g
Problems
Troubleshooting
Nothing appears on the
screen.
· Please check that the power cord and line connection
between the camera and monitor are fixed properly.
· Please check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the screen
is dim.
· Is lens stained with dirt? Clean your lens with soft,
clean cloth.
· Set the monitor to proper condition.
· If the camera is exposed to too strong light, change
the camera position.
The image on the screen
is dark.
· Adjust the contrast feature of the monitor.
· If you have an intermediate device,
set the 75Ω / Hi-Z properly
(Please check the impedance)
The camera is not working
properly, and the surface
of the camera is hot.
· Please check that you have properly connected the
camera to an appropriate power source.
The screen flickers
continually.
· Please check that direction of camera turns toward
the Sun.
5. Installation
*
OPTION
- Varifocal Lens adjustment
: Varifocal Lens (2.8~12mm)
Focus
Knob
Zoom
Knob
LED
COVER
- Zoom (Tele-Wide)
Unlock the zoom lever by turning
counterclockwise.
Move the lever to adjust the zoom.
Lock the lever by turning clockwise.
- Focus (Near-Far)
Unlock the focus lever by turning
counterclockwise.
Move the lever to adjust the focus.
Lock the lever by turning clockwise.
< NOTE : >
With difficulty of lens adjustment of VF IR Type.
You could uncover the LED cover.
Push the hook on both sides to separate the LED COVER and adjust
the lens.
PUSH
PUSH
Page 9
ModDeEl L
Hi-Res Indoor Dome Camera
Image Device
1/3" HIGH RESOLUTION SUPER SENSITIVE CCD
Effective Pixels
NTSC : 976(H)X494(V), PAL : 976(H)X582(V)
Scanning System
NTSC 525 Lines PAL 625 Lines 2:1 Interlaced
Synchronization
Internal
H.Resolution
700TV Lines(Color)/ 750TV Lines(B/W)
Min. illumination
0.1 lux / IR version (0 lux, 3 lux/IR ON)
Video OUT
1.0 Vp-p / 75 ohm
S/N Ratio
More than 50db
Gain Control
AUTO
LENS
3.6mm, 4.3mm, 6mm board Lens
2.8~12mm VF Auto DC iris Lens
Shutter speed
AUTO
White Balance
ATW (2,500°K ~ 10,000°K)
Day&Night
AUTO (COLOR, B/W)
DPC
Dead Pixel Compensation
Power Source
12VDC
Power Consumption
Board Type : 80mA
Board IR Type : 90mA(IR OFF) / 285mA(IR ON)
VF Type : 100mA
VF IR Type : 140mA(IR OFF) / 330mA(IR ON)
Viewable Distance
UP to 20M at Moonless Night
MTBF
20,000 hours
Operating Temp.
-10°C ~ 50°C
Storage Temp.
-20°C ~ 60°C
Measurement (mm)
114(Φ) x 90(H)
Weight (Approx.g)
Board Type : 160g / Board IR Type : 180g
VF Type : 185g / VF IR Type : 205g
Problems
Troubleshooting
Nothing appears on the
screen.
· Please check that the power cord and line connection
between the camera and monitor are fixed properly.
· Please check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the screen
is dim.
· Is lens stained with dirt? Clean your lens with soft,
clean cloth.
· Set the monitor to proper condition.
· If the camera is exposed to too strong light, change
the camera position.
The image on the screen
is dark.
· Adjust the contrast feature of the monitor.
· If you have an intermediate device,
set the 75Ω / Hi-Z properly
(Please check the impedance)
The camera is not working
properly, and the surface
of the camera is hot.
· Please check that you have properly connected the
camera to an appropriate power source.
The screen flickers
continually.
· Please check that direction of camera turns toward
the Sun.
3EA)
Camera
set
3EA)
48.2
90
120°
PUSH
PUSH
5-3. How to mount to Celling
DC
BNC or
JACK
Female
Female
RCA
Driling
template
Plastic
anchor (
Tapping
Dome Cover
① Fix the supplied drilling template on the
② Drill holes and Insert plastic anchors into the
(in case of masonry ceiling or
③ Fix the camera set using supplied tapping
④ Push lock the dome cover ass’y after checking camera
wall).
wall.
screws.
hole
Screw (
Ass'y
direction.
Page 10
ModDeEl L
Hi-Res Indoor Dome Camera
Image Device
1/3" HIGH RESOLUTION SUPER SENSITIVE CCD
Effective Pixels
NTSC : 976(H)X494(V), PAL : 976(H)X582(V)
Scanning System
NTSC 525 Lines PAL 625 Lines 2:1 Interlaced
Synchronization
Internal
H.Resolution
700TV Lines(Color)/ 750TV Lines(B/W)
Min. illumination
0.1 lux / IR version (0 lux, 3 lux/IR ON)
Video OUT
1.0 Vp-p / 75 ohm
S/N Ratio
More than 50db
Gain Control
AUTO
LENS
3.6mm, 4.3mm, 6mm board Lens
2.8~12mm VF Auto DC iris Lens
Shutter speed
AUTO
White Balance
ATW (2,500°K ~ 10,000°K)
Day&Night
AUTO (COLOR, B/W)
DPC
Dead Pixel Compensation
Power Source
12VDC
Power Consumption
Board Type : 80mA
Board IR Type : 90mA(IR OFF) / 285mA(IR ON)
VF Type : 100mA
VF IR Type : 140mA(IR OFF) / 330mA(IR ON)
Viewable Distance
UP to 20M at Moonless Night
MTBF
20,000 hours
Operating Temp.
-10°C ~ 50°C
is not working
6. Troubleshooting
If there are problems in operating, please refer to the checklist below.
If the problem persists, please contact the agent where this product is purchased.
Problems Troubleshooting
· Please check that the power cord and line connection
Nothing appears on the
screen.
The image on the screen
is dim.
between the camera and monitor are fixed properly.
· Please check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
· Is lens stained with dirt? Clean your lens with soft,
clean cloth.
· Set the monitor to proper condition.
· If the camera is exposed to too strong light, change
the camera position.
The image on the screen
is dark.
The camera
properly, and the surface
of the camera is hot.
The screen flickers
continually.
· Adjust the contrast feature of the monitor.
· If you have an intermediate device,
set the 75Ω / Hi-Z properly
(Please check the impedance)
· Please check that you have properly connected the
camera to an appropriate power source.
· Please check that direction of camera turns toward
the Sun.
Page 11
ModDeEl L
Hi-Res Indoor Dome Camera
Image Device
1/3" HIGH RESOLUTION SUPER SENSITIVE CCD
Effective Pixels
NTSC : 976(H)X494(V), PAL : 976(H)X582(V)
Scanning System
NTSC 525 Lines PAL 625 Lines 2:1 Interlaced
Synchronization
Internal
H.Resolution
700TV Lines(Color)/ 750TV Lines(B/W)
Min. illumination
0.1 lux / IR version (0 lux, 3 lux/IR ON)
Video OUT
1.0 Vp-p / 75 ohm
S/N Ratio
More than 50db
Gain Control
AUTO
LENS
3.6mm, 4.3mm, 6mm board Lens
2.8~12mm VF Auto DC iris Lens
Shutter speed
AUTO
White Balance
ATW (2,500°K ~ 10,000°K)
Day&Night
AUTO (COLOR, B/W)
DPC
Dead Pixel Compensation
Power Source
12VDC
Power Consumption
Board Type : 80mA
Board IR Type : 90mA(IR OFF) / 285mA(IR ON)
VF Type : 100mA
VF IR Type : 140mA(IR OFF) / 330mA(IR ON)
Viewable Distance
UP to 20M at Moonless Night
MTBF
20,000 hours
Operating Temp.
-10°C ~ 50°C
Storage Temp.
-20°C ~ 60°C
Measurement (mm)
114(Φ) x 90(H)
Weight (Approx.g)
Board Type : 160g / Board IR Type : 180g
VF Type : 185g / VF IR Type : 205g
Problems
Troubleshooting
Nothing appears on the
screen.
· Please check that the power cord and line connection
between the camera and monitor are fixed properly.
· Please check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the screen
is dim.
· Is lens stained with dirt? Clean your lens with soft,
clean cloth.
· Set the monitor to proper condition.
· If the camera is exposed to too strong light, change
the camera position.
The image on the screen
is dark.
· Adjust the contrast feature of the monitor.
· If you have an intermediate device,
set the 75Ω / Hi-Z properly
(Please check the impedance)
The camera is not working
properly, and the surface
of the camera is hot.
· Please check that you have properly connected the
camera to an appropriate power source.
The screen flickers
continually.
· Please check that direction of camera turns toward
the Sun.
48.2
90
7. Dimension
Ø81.4
(mm)
120°
Ø1
13.8
Page 12
ModDeEl L
1.0 Vp-p / 75 ohm
More than 50db
Shutter speed
Power Source
12VDC
-10°C ~ 50°C
8.
Specification
Model
Image Device
Effective Pixels
Scanning System
Synchronization
H.Resolution
Min. illumination
Video OUT
S/N Ratio
Gain Control
LENS
White Balance
Day&Night
Hi-Res Indoor Dome Camera
1/3" HIGH RESOLUTION SUPER SENSITIVE CCD
NTSC : 976(H)X494(V), PAL : 976(H)X582(V)
NTSC 525 Lines PAL 625 Lines 2:1 Interlaced
Internal
700TV Lines(Color)/ 750TV Lines(B/W)
IR version (0 lux, 3 lux / IR ON)
0.1 lux / IR version (0 lux, 3 lux/IR ON)
AUTO
3.6mm, 4.3mm, 6mm board Lens
2.8~12mm VF Auto DC iris Lens
AUTO
ATW (2,500°K ~ 10,000°K)
AUTO (COLOR, B/W)
DPC Dead Pixel Compensation
Board Type : 80mA
Power Consumption
Viewable Distance
MTBF
Operating Temp.
Storage Temp.
Measurement (mm)
Weight (Approx.g)
* Specifications are subject to change without prior notice for improvement.
Board IR Type : 90mA(IR OFF) / 285mA(IR ON)
VF Type : 100mA
VF IR Type : 140mA(IR OFF) / 330mA(IR ON)
UP to 20M at Moonless Night
20,000 hours
-20°C ~ 60°C
114(Φ) x 90(H)
Board Type : 160g / Board IR Type : 180g
VF Type : 185g / VF IR Type : 205g
Loading...