Page 1
1
TC2-HDMIIP_manual_en
TECHCONNECT TC2-HDMIIP
OWNERS MANUAL
www.visionaudiovisual.com/techconnect/tc2-hdmiip
Page 2
2
TC2-HDMIIP_manual_en
DECLARATION OF CONFORMITY
Where applicable Vision products are certified and comply with all known local regulations to a
‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in compliance with RoHS (EU directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be returned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle, is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
All products are designed and imported into the EU by ‘Vision’ who is wholly owned by ‘Azlan
Logistics Ltd.’, Registered in England Nr. 04625566 at Lion House, 4 Pioneer Business Park,
Clifton Moor, York, YO30 4GH. WEEE Registration: GD0046SY
DECLARATION OF ORIGIN
All Vision products are made in the People’s Republic of China (PRC).
Page 3
3
TC2-HDMIIP_manual_en
USE ONLY DOMESTIC AC OUTLETS
Connecting the unit to an outlet supplying a higher voltage may create a fire hazard.
HANDLE THE POWER CORD WITH CARE
Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself.
Pulling the cord may damage it. If you do not intend to use your unit for any considerable
length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and
try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could
the cord be damaged, but a short circuit could also be caused with a consequent fire hazard.
PLACE OF INSTALLATION
Avoid installing this product under the following conditions:
• Moist or humid places
• Places exposed to direct sunlight or close to heating equipment
• Extremely cold locations
• Places subject to excessive vibration or dust
• Poorly ventilated places
Do not expose this product to dripping or splashing. DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS PRODUCT!
MOVING THE UNIT
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect
the interconnection cords with other units.
WARNING SIGNS
If you detect an abnormal smell or smoke, turn this product off immediately and unplug the
power cord. Contact your reseller or Vision.
PACKAGING
Save all packing material. It is essential for shipping in the event the unit ever needs repair.
IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE,
DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY.
OVERVIEW
This product converts HDMI signal into native ethernet signal and allows the signal to be routed
through a normal local area network.
Page 4
4
TC2-HDMIIP_manual_en
TRANSMITTER
1. 5V 2A Power input
2. HDMI Input
3. CAT5e/6 Output
4. Reset Button
1 2 3
4
Page 5
5
TC2-HDMIIP_manual_en
RECEIVER
1. CAT5e/6 Output
2. Reset button
3. 5V 2A Power input
4. HDMI Output
1 2 3
4
Page 6
6
TC2-HDMIIP_manual_en
INSTALLATION
NOTE: This product is peer to peer and must be used as a set.
NOTE: A power supply is required at each end.
Connect cables. Notes:
1. CAT5e/6 cables used should be wired to IEEE-568B standard. Unshielded Twisted Pair
(UTP) or Shielded Twisted Pair (STP) are both acceptable.
2. Transmitter can connect directly to receiver without a cross-over cable.
3. The transmitter and receiver automatically find each other on a network when patched
through a network switcher.
NOTE: It is not possible to use a network router as a distribution amplifier.
MULTIPLE SETS ON LAN
If more than one transmitter / receiver sets share same network:
METHOD 1:
Create a Virtual LAN on the network switch
for each
transmitter and receiver set. Example:
Connect 15 transmitters to ports 1-15
Connect 15 receivers to ports 16-30
Create VLAN_1 and assign ports 1 and 16
Create VLAN_2 and assign ports 2 and 17 etc…
METHOD 2:
If method 1 does not work:
1. Connect transmitter or receiver directly to computer.
2. Power on device
Page 7
7
TC2-HDMIIP_manual_en
3. Change IP address of computer. On a Windows PC go Control Panel > Network and
Internet > Network and Sharing Centre. Click on Local Area Network.
4. Click Properties
5. Select Internet Protocol Version 4 (TCP/IPv4). Click Properties.
Page 8
8
TC2-HDMIIP_manual_en
6. Set IP address as follows:
7. In browser enter device IP address to access the control panel. Default addresses:
Transmitters (Tx) 192.168.168.55 / Receivers (Rx) 192.168.168.56
8. Set IP addresses for devices to:
Page 9
9
TC2-HDMIIP_manual_en
a. 1
st
set: Tx 192.168.168.55 / Rx 192.168.168.56
b. 2
nd
set: Tx 192.168.168.57 / Rx 192.168.168.58
c. 3
rd
set: Tx 192.168.168.59 / Rx 192.168.168.60
d. etc
TROUBLESHOOTING
If your system is not operating properly, please refer to the following information. If the
problem persists, disconnect from power and contact your AV reseller immediately.
Problem
Correction
Yellow light flashing
slowly
Transmitter and receiver are reversed
Source device not outputting signal
HDMI input cable not working
Yellow light flashing
quickly, no image
Reduce resolution of source to match display device.
Check HDMI output cable
No yellow light
Check network cable
Network cable is too long
(network cables are limited to 100m between devices)
Image flashing or
colour incorrect
Press reset button
Check CAT5e/6 cable wiring. It should be wired to 568B
standard at both ends:
If one end has green and orange swapped this is a crossover cable and cannot be used.
Page 10
10
TC2-HDMIIP_manual_en
SPECIFICATIONS
TRANSMITTER DIMENSIONS: 110 x 58 x 26 mm (length x width x height)
RECEIVER DIMENSIONS: as above
PRODUCT WEIGHT: 0.48 kg per set
CONSTRUCTION MATERIAL: Metal
COLOUR: White
TECHNICAL DETAILS:
Standard: IEEE-568B
Cable: CAT5/5E/6
Bandwidth: 50mbs
Frame rate: 30fps
HDMI format supported: 1080p @ 50/60Hz
HDMI Version: partial 1.4 e.g. 3D not supported
Maximum cable length: Standard Ethernet rules apply
CAT5: 80m between ethernet devices
CAT5e: 100m between ethernet devices
CAT6: 120m between ethernet devices
Maximum resolution: 1080p@50/60Hz
Operating temperature range: -5 ~35
Operating humidity range: 20%~90%
Power Consumption: 3 Watts (max) each
INPUTS:
1 x HDMI (type A)
OUTPUTS:
1 x HDMI (type A)
2 x POWER SUPPLY: 100-240v 50/60Hz AC External Power Supply – integrated transformer/plug
type. DC Output 5V 2A, DC Cable 1.8m. Transformer dimensions: 76 x 44 x 26mm.
Interchangeable prongs including UK, EU, AU, US.
Note: a normal figure-8 cable can be plugged into the transformer if preferred.
COMPLIANCES: RoHS, WEEE, CE, and CB compliant.
ACCESSORIES
2 x Mounting ears
Page 11
11
TC2-HDMIIP_manual_en
WARRANTY
This product comes with a 2-year return to base warranty, effective from the date of purchase.
This warranty applies only to the original purchaser and is not transferable. For the avoidance of
doubt, this will be taken from the information held by the appointed national distributor at the
point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to
notify the national distributor via your AV reseller. The liability of the manufacturer and its
appointed service company is limited to the cost of repair and/or replacement of the faulty unit
under warranty, except for death or injury (EU85/374/EEC). This warranty protects you against
the following:
• Failure of any components, including the power supply.
• Damage when the product is first removed from its packaging if reported within 24 hours of
purchase.
If you find you do have a problem with this product, you should contact the AV reseller you
purchased this product from. The original purchaser is responsible for shipment of the product
to the manufacturer’s appointed service centre for repair.
We will endeavour to return repaired units within 5 working days, however this may not always
be possible, in which case it will be returned as soon as practicably possible. In line with our
WEEE commitments, the manufacturer endeavours to replace the faulty parts of the product
rather than replacing the whole unit. This warranty does not protect this product against faults
caused by abuse, misuse, incorrect installation, unstable or faulty power input, which might be
caused by ignoring the guidelines set out in this manual.
LEGAL DISCLAIMER: Because we are committed to improving our products, the details above
may change without prior warning. This User Manual is published without warranty and any
improvements or changes to the User Manual necessitated by typographical errors, inaccuracies
of current information, or improvements to programs and/or equipment, may be made at any
time and without notice. Such changes will be incorporated into new editions of the User
Manual.
Loading...