Page 1
1
TC2-HDMI41_manual_en_v2.doc
TECHCONNECT TC2-HDMI41
OWNERS MANUAL
www.visionaudiovisual.com/techconnect/tc2-hdmi41
Page 2
2
TC2-HDMI41_manual_en_v2.doc
DECLARATION OF CONFORMITY
Where appli cable Vision products are certified and comply with all known local regulations to a
‘CB Cer t ificatio n’ stand ard. Vision commits to en sure all pro ducts are fully comp liant with a ll
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in com pliance wit h RoHS (EU directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be returned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dan gerous voltage” within the product’s enclosure that may be
of sufficient magnitude to consti tute a ri sk of electric shock to p er sons.
The exclamation point within an equ ilateral triangle, is intended to alert the user to the p r esen ce of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
All products are designed and imported into the EU by ‘Vision’ who is wholly o wned by ‘Azlan
Logistics Ltd.’, Registered in England Nr. 04625566 at Lion House, 4 Pi o ne er Bus i ness P ark,
Clifton Moor, York, YO30 4GH. WEEE Regis tration : GD0046SY
DECLA RATION OF ORIGI N
All Vision products are made in the People’s Republic of China (PRC).
Page 3
3
TC2-HDMI41_manual_en_v2.doc
USE ONLY D OMESTIC AC OU TL ETS
Connecting the unit to an outlet supplying a higher voltage may create a fire hazard.
HANDL E T HE PO W ER CORD W ITH CA RE
Do not disconnect the plug from the AC outlet by pulling the cord; always pull th e plug itself.
Pulling the cord may damage it. If you do not intend to use your unit for any considerable
length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and
try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could
the cord be damaged, but a short circuit could also be caused with a consequent fire hazard.
PLACE OF INSTALLATION
Avoid installin g this prod uct under the followin g conditions:
• Moist or humid pla ces
• Places exposed to direct sunlight or close to heating equipment
• Extr emely cold loc ations
• Places subject to exce ssiv e vib ratio n or du st
• Poor ly ventilat ed place s
Do not expose this pro d uct to dripping or splashing . DO NOT PLA CE OBJ E CTS FILLE D WI TH
LIQU ID S O N OR NE A R THIS P RO DUCT!
MOVING THE UNI T
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect
the interconnection cords with other units.
WARNING SIGNS
If you detect an abnormal smell or smoke, turn this product off immediately and unplug the
power cord. Contact your reseller or Vision.
PACKAGING
Save a ll packing material. It is essential fo r s hipping in the event the uni t ev er needs repair.
IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE,
DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY.
Page 4
4
TC2-HDMI41_manual_en_v2.doc
FRONT AND REAR PANELS
1. IR Receiver
2. Input Indictor LEDs
3. Select button
4. Mode button
5. 5V 2A Power input
6. HDMI Inputs
7. HDMI Output
8. RS-232
9. EDID selector
10. Mini USB-B connector - for firmware updates
1 2 5 6 7 3 8 9 10
4
Page 5
5
TC2-HDMI41_manual_en_v2.doc
INSTALLATION
1. CONNECT INPUTS Plug HDMI cables into inputs. Note input and output cables are not
included with this product.
2. CONNECT OUTPUTS
3. TURN MAIN SOURCE DEVICE ON Keep other source devices off at this stage.
4. TURN SWITCHER ON Plug in to mains power and turn on.
5. TURN DISPLAY DEVICE ON
MODE
The mode button allows the installer to set priorities. When the device is turned on, or when the
connection is lost:
1/ Resumes last input
2/ Goes to input 1
3/ Goes to last input plugged in
Page 6
6
TC2-HDMI41_manual_en_v2.doc
RS-232 CONTROL
Baud Rate 9600 bps
Data Bits 8 bits
Check Bits None
Stop Bits 1 bit
Flow Control None
1. Swit ch command: swt+space+xx+enter
xx represents:
• 01~04 Input port
• 05 Next input e.g. 3 to 4
• 06 Previous input e.g. 3 to 2
2. Obtain current port: bc+space+enter
3. Standby command: pws+enter
Page 7
7
TC2-HDMI41_manual_en_v2.doc
EDID (EXTE NDED DISP L AY IDENTIFIC ATION DATA)
This ena bles the sou r ce device to ‘a sk’ the disp lay device what resoluti o n it is, and ou tput that
resolution.
Position Function
000
(default)
Use video resolution and au dio capabilit ies of output dev ice.
If display dev i ce no t on switcher defaults to 1080P 3D (stereo audio)
001 Fixed to 1080P 3D (stereo audio)
010 Fixed to 1080P (stereo audio)
011 Fixed to 1080I (stereo audio)
100 Fixed to 1080P (5.1 audio)
101 Fixed to 1080P (7.1 audio)
TROUBLESHOOTING
If your system is not operating properly, please refer to the following information. If the
problem persists, disconnect from power and contact your AV reseller immediately.
Problem
Correction
No status lights
• Check input and output cables
• Check active source is turned on
Sta tu s light flashing
• Chec k HDMI output cable
No power light
• Try alternative power supply
Page 8
8
TC2-HDMI41_manual_en_v2.doc
SPECIFICATIONS
PRODUCT DIMENSIONS:280 x 95 x 24 mm (length x width x height)
PACKAGED DIMENSIONS: 300 x 145 x 60 mm
PRODUCT WEIGHT: 0.5 kg
CONSTRUCTION MATERIAL: Metal
COLOU R: W hi t e
TECHNICAL DETAIL S:
Input Video Signal: 0.5-1.0 volts p-p
Input DDC Signal: 5 volts p-p (TTL)
Maximum Video Format Supported: 1080P
Audio Format Supported: DTS-HD、Dolby HD、PCM 7.1
Output Video: HDMI 1.4 with 3D
Operati ng Tem p eratur e R a n ge: -5 to +35°C (-41 to +95 °F)
Operat i n g H umidity Range: 5 to 9 0 % RH (no condens a ti o n)
Power Consumption: 4 watts (Max.)
INPUTS:
4 x HDMI (type A)
1 x RS-232 (9-pi n D-sub)
OUTPUTS:
1 x HDMI (type A)
POWER SUPPLY: 100-240v 50/60Hz AC 5 volt / 2 amp
Transformer integrated into plug. Includes interchangeable plugs: UK/EU/US/AU. DC tail length:
1.8m. Transformer dimensions: 66 x 43 x 32mm
COMPLIANCE RoHS, WEEE & CE Compliant
ACCESSORIES
2 x Mounting ears
1 x Remote Control
Page 9
9
TC2-HDMI41_manual_en_v2.doc
WARRANTY
This product comes with a 2-year return to base warranty, effective from the date of purchase.
This warranty applies only to the original purchaser and is not transferable. For the avoidance of
doubt , th is will be taken fr o m th e informa tion held by the appointed nationa l distribu tor at the
point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to
notify the national distributor via your AV reseller. The lia bility of the manufacturer and it s
appointed service company is limited to the cost of repair and/or replacement of the faulty unit
under warranty, except for death or injury (EU85/374/EEC). This warranty protects you against
the following:
• Failure of any components, including the power supply.
• Damage when the product is first removed from its packaging if reported within 24 hours of
purchase.
If you find you do have a problem with this product, you should contact the AV reseller you
purchased this product from. The original purchaser is responsible for shipment of the product
to the manufacturer’s appointed service centre for repair.
We will endeavou r to return repaired units within 5 work ing days, h owe ver this may no t always
be possibl e, in which case it will be returned as soon as pr ac ticably possible. In line with our
WEEE commitments, the manufacturer endeavours to replace the faulty parts of the product
rather than replacing the whole unit. This warranty does not protect this product against faults
caused by abuse, misuse, incorrect installation, unstable or faulty power input, which might be
cau sed by ignoring the guidelines se t out in t his manual.
LEGAL DISCLAIMER: Because we are committed to improving our products, the details above
may change without prior warning. This User Manual is published without warranty and any
improvements or changes to the User Manual necessitated by typographical errors, inaccuracies
of current information, or improvements to programs and/or equipment, may be made at any
time an d wit hout not ice. Such changes will be incorporated into new editions o f the Us er
Manual.
Loading...