Visidec VF-AT Installation Instructions Manual

Installation Instructions

VF-AT

Component Checklist

Focus | Articulated Arm

M4x10/12/16mm (x4)

Phillips Head Mounting Screws

Primary Arm

Cable Cover

Cable Stops

(x2)

Pole Top Cap

Cable Clip

Secondary Arm

Cable Cover

M8x30mm

Screw

Bolt Through

Base

Steel Washer

Arm Assembly

Pole Assembly Desk Clamp Assembly

5mm Allen Key

HARDWARE Display Mounting

Screws

! IMPORTANT - Install Visidec Focus Articulated Arm as per installation instruction.

! This product supports a maximum load of 8kg (17.6lbs).
! The manufacturer accepts no responsibility for incorrect installation.

IMPORTANT INFORMATION:

Step 1. Check Components

Check what you have received against the component checklist and hardware above.

Step 2. Mount Pole Assembly

Option 1: Bolt Through Option 2: Mount using Desk Clamp

Pole Assembly

Pressure Plate

2.1 Remove both the Pressure
plate and M10 Desk Clamp
Screw.

2.2 Fasten the Desk Clamp to the Bolt
Through Base & Pole Assembly using the
M8 x 30mm Screw and Tighten Firmly.

M10 Desk Clamp
Screw

M8 x 30mm Screw

Bolt Through Base

Pole Assembly

Slot

Slot Tab

Bolt Through Base

Steel Washer

M8x60mm Screw

5mm Allen Key

It is recommended that the Pole Assembly be
mounted towards the rear edge of the work surface.

Note: Ensure that the Slot Tab in the Bolt
Through Base fits snugly into the Slot on the
Pole Assembly.

The Visidec logo on the Bolt Through Base
must face the front of this assembly.

5mm Allen Key

5mm Allen Key

M8x60mm

Screw

Step 2. Mount Pole Assembly (cont.)

Step 3. Mount Arm Assembly

2.4 Remove the M8 x 16mm Socket Head Countersunk

Screws to release the Desk Clamp Bracket.

2.3 The Desk Clamp bracket can be repositioned to suit different mounting
surface thicknesses. The maximum mounting surface thicknesses supported
are listed below from the Top to Middle and Bottom Screw Holes.

TTMMBB

M8 x 16mm Socket
Head Countersunk
Screw

5mm Allen Key

Desk Clamp Bracket

Pressure Plate

Table Top

M8 x 16mm Socket
Head Countersunk
Screw

M10 Desk Clamp Screw

5mm Allen Key

5mm Allen Key

5mm Allen Key

Arm Assembly

Pole Top Cap

2.5 Place in desired
location.

If you need to reposition the desk clamp bracket or you have no
access to the rear of your table continue to Step 2.4.
If you DO NOT need to reposition the desk clamp bracket and
you have access to the rear of your table skip to Step 2.7.

2.6 Reattach Desk
Clamp Bracket.

2.7 After positioning
your Pole Assembly,
screw Pressure Plate in
and Tighten Firmly.

3.1 Unlock Handgrip
and raise so that
Handgrip Tab
protrudes.

3.2 Slip the Arm
Assembly over the
Handgrip Tab and then
onto the Pole.

3.3 Slide the Arm
Assembly and Handgrip
down the pole before
locking the handgrip at
the desired height.

3.4 Insert Pole Top
Cap into Pole. This is
also where the Allen
Key is stored.

Desk Clamp Bracket

Handgrip Tab

Top 0 - 32mm (default)
Middle 7 - 47mm
Bottom 22 - 62mm

Top 29 - 69mm
Middle 43 - 84mm
Bottom 59 - 99mm