
ArIA 2 lIGht
Eigenschaften und Klang
Die A
rIA
2 l
IGht
ist eine kleine 2-Wege
Regalbox mit 2 Tiefmitteltönern W 100 S
und der Hochtonkalotte G 20 SC. In kleinen Räumen und bei Regalaufstellung
hat sie bereits ein beachtliches Tieftonfundament, so dass ein Subwoofer nicht
unbedingt notwendig ist. Mit einem guten aktiven Subwoofer wird jedoch die
Klangfülle wesentlich größerer HiFi-Boxen erreicht.
Durch das größere Gehäuse mit der
D‘Ap polito Anordnung der A
rIA
2 l
IGht
wird im Wesentlichen ein höherer maximaler Schalldruck im Vergleich zur kleinen ArIA lIGht erzielt.
Characteristics and sound properties
The ArIA 2 lIGht is a small-sized 2-band
shelf-top speaker system that uses two
W 100 S mid-bass units and one G 20 SC
dome tweeter. In smaller rooms and if
used as a shelf-mounted unit, the system has a considerable bass foundation
which means that a separate subwoofer
is not required. However, if coupled with
a good powered subwoofer, the range
of tonality of far larger hi-fi speakers is
achieved.
The larger cabinet and the D‘Appolito arrangement in the A
rIA
2 l
IGht
provide a
far greater maximum sound pressure in
comparison with the smaller ArIA lIGht.
Nennbelastbarkeit Rated power 60 W
Musikbelastbarkeit Maximum power 100 W
Nennimpedanz Nominal impedance 4 Ω
Übertragungsbereich Frequency response (–10 dB) 65–30
000 Hz
Mittl. Schalldruckpegel Mean sound pressure level 85 dB (1 W/1 m)
Trennfrequenz Cut-off frequency 2500 Hz
Gehäuseprinzip Principle of Housing Bassreflex / bass reflex
Gehäusemaße Cabinet
Nettovolumen Net volume 8 l
Höhe Height 396 mm
Breite Width 160 mm
Tiefe Depth 210 mm
28 HiFi Bauvorschläge 2008

ArIA 2 lIGht
Bestückungsliste für 1 Box
Der Bausatz enthält alle in dieser Bestückungsliste aufgeführten Bauteile, jedoch kein Gehäuse.
Hochtöner G 20 SC - 8 Ω 1 St.
Tieftöner W 100 S - 8 Ω 2 St.
Frequenzweiche „ArIA 2 lIGht“
Bassreflexrohr BR 6.8
(volle Länge) 2 St.
Anschlussklemme ST 77 1 St.
Dämpfungsmaterial
Senkkopfschrauben 3,5 x 25 mm 18 St.
Kabel 2 x 1,5 mm² 1 m
Zuschnittliste für 1 Box
Teile Maße (mm) Anzahl
Material: 16 mm Spanplatte oder MDF
Front, Rückwand 396 x 160 2
Seiten 396 x 178 2
Deckel, Boden 178 x 128 2
Polyesterwolle
½ Btl.
Component parts list for 1 box
The kit includes all the components listed here but not the cabinet.
Tweeter G 20 SC - 8 Ω 1 pc.
Woofer W 100 S - 8 Ω 2 pc.
Crossover „
Bass reflex BR 6.8
tube (full length) 2 pcs.
Terminal ST 77 1 pc.
Damping Polyester
material wool ½ bag
Countersunk
screws 3.5 x 25 mm 18 pcs.
Cable 2 x 1.5 mm² 1 m
Aufbau
Für den Korpus benötigt man 16 mm
starke Platten. Zuerst werden in die Platten die nötigen Aussparungen gesägt
und die Fasen angebracht. Dafür eignet sich z.B. eine auf Gehrung einstellbare Stich- oder Handkreissäge. Nachdem dann das Gehäuse komplettiert
wurde, werden nach Möglichkeit die
Einfräsungen für die Lautsprecher realisiert. Zum Schluss wird die Box noch
bestückt.
ArIA 2 lIGht“
Bedämpfung
Das Dämpfungsmaterial wird locker in
die Gehäuse gestopft.
Inner damping
The damping material is loosely arranged in the cabinet.
Cabinet parts list for 1 box
Parts Size (mm) Quantity
Material: 16 mm MDF or chipboard
Front, rear panel 396 x 160 2
Side panle 396 x 178 2
Top, bottom panel 178 x 128 2
Aufgrund der geringen Gehäusegröße
ist eine Befestigung der Frequenzweiche im Gehäuse schwierig. Sie kann aber
auch einfach in Dämpfungsmaterial gewickelt und in die Box gelegt werden,
wenn die Rückwand nicht abschraubbar montiert wird.
Construction
The cabinet body uses 16 mm boards.
First of all, cut the holes in the boards
and apply the bevels. This can be done
using an electric jigsaw or hand-held circular saw set to the required angle. Once
the cabinet has been completed, apply
the milling work for the loudspeaker. Finally, fit the cones.
Since the cabinets are relatively small, it
is hardly possible to mount the cross over
inside the housing. It can, however, simply be wrapped in damping material and
placed inside the speaker if the rear wall
is not removable.
HiFi Bauvorschläge 2008 29

ArIA 2 lIGht
30 HiFi Bauvorschläge 2008