Visam VTP-BC70, VTP-BC100 Instruction Manual

Instruction Manual

VISAM TouchPanel

VTP-BC70 / VTP-BC100

A product of the the

VBASE - HMI/SCADA – family

Document: HB_VTPBC_70_100v1.0e_FINAL.doc

Version: 1.0, English

2 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

Copyright © 2015 by VISAM GmbH

All rights reserved

VISAM GMBH

Irlicher Straße 20

D-56567 Neuwied

Tel.: [phone] – 0
Fax: [phone] – 9

E-Mail: [e-mail]

Internet: http://www.visam.de

Technical Support

Tel.: [phone] – 40

E-Mail: [e-mail]

We have taken all possible measures to ensure the correctness and completeness of this
documentation. Despite all care, errors cannot be avoided and we would appreciate any
information or ideas at any time.

We point out that the in the document used software and hardware terms as well as the
trademarks of their respective companies are generally subject to trademark protection,
trademark or patent protection.

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 3

HB_VTPBC_70_100v1.0e_FINAL
.doc

Table Of Content

1 IMPORTANT EXPLANATION ............................................................ 5

1.1 Legal Bases ..................................................................................... 5

1.1.1 Copyright ............................................................................................. 5

1.1.2 Personnel Qualification .......................................................................... 5

1.1.3 Intended Use ....................................................................................... 5

1.1.4 License Agreement ................................................................................ 5

1.2 Range of validity .............................................................................. 6

1.3 Used symbols .................................................................................. 6

2 INTRODUCTION ........................................................................... 7

2.1 Regarding this document................................................................... 7

2.2 The Article – and Model number ......................................................... 7

3 SPECIFICATION ........................................................................... 8

3.1 System data .................................................................................... 8

3.2 Interfaces ....................................................................................... 8

3.3 LCD Display ..................................................................................... 8

3.4 Touchscreen .................................................................................... 9

3.5 Power Supply ................................................................................... 9

3.6 Integrated Software ......................................................................... 9

3.7 Interface Arrangement ...................................................................... 9

3.8 Connection Assignment ................................................................... 11

3.8.1 Power Supply ......................................................................................11

3.9 Power Switch ................................................................................. 11

3.10 Environment Conditions ................................................................ 11

3.11 Safety ........................................................................................ 11

4 SOFTWARE-SETTINGS ................................................................ 12

4.1 Setup / Changing of the network (IP)-address ................................... 12

4.2 Save changes to settings permanently .............................................. 13

4.3 Automatic Startup of the HMI-Application .......................................... 13

4.4 FTP-Server, Data Transmission ........................................................ 13

4.5 Touchscreen Calibration .................................................................. 15

4.6 Remote control of the device via network .......................................... 16

4.7 Connect network share ................................................................... 18

4.8 Additional Settings in Windows CE .................................................... 19

4.9 Tools ............................................................................................ 19

4.9.1 The Tool CE NotepadPlus ....................................................................19

4.9.2 The Tool cmd .....................................................................................19

4.9.3 The Tool control ..................................................................................19

4.9.4 The Tool Registry Saver .......................................................................19

4.9.5 The Tool vncconfig ..............................................................................19

4.9.6 The Tool Wordpad ...............................................................................19

4.9.7 The Tool Resolution Utility ....................................................................19

4.10 VTP Tool ..................................................................................... 20

4.10.1 General ............................................................................................20

4.10.2 User / Rights ....................................................................................21

4.10.3 FTP-Server .......................................................................................22

4.10.4 Telnet-Server ...................................................................................24

4.10.5 Display Settings ................................................................................24

5 APPENDIX ................................................................................. 25

5.1 Fuse ............................................................................................. 25

4 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

5.2 PIN-Assignment of the serial interface .............................................. 26

5.2.1 Serial interface RS-232/422/485 (COM1) ................................................26

5.2.2 Serial interface RS-422/485 (COM2) / RS-485 (COM3) .............................26

5.2.3 USB Verbindung ..................................................................................27

5.3 Dimension and Cutout .................................................................... 28

5.3.1 Weight (VTP-BC70 / 100) .....................................................................28

5.3.2 Cutout ................................................................................................28

5.4 Illustration Directory ....................................................................... 30

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 5

HB_VTPBC_70_100v1.0e_FINAL
.doc

1 Important Explanation

To ensure the user a fast installation and startup of the described devices it is
essential to carefully read and note the following instructions and hints.

1.1 Legal Bases

1.1.1 Copyright

This document including all images therein is copyrighted. Any use of this
document that infringes the copyright provision is not permitted. Reproduction,
translation into other languages as well as electronic and photo-technical
archiving and alteration requires the written approval of VISAM GmbH, D-56567
Neuwied. Violations will be prosecuted with damage claims.
The VISAM GmbH reserves changes that serve the technical improvement.
All rights in the event of grant of a patent or utility model protection are
reserved to VISAM GmbH. Foreign products are always named without referring
to patent rights. The existence of such rights cannot be excluded.

1.1.2 Personnel Qualification

The construction of the following instruction and the usage of the VBASE-product
family require basic knowledge about the used windows operating system and
the used remote systems. (e.g. SPS)!

The in this document described product use is directed exclusively to
professionals or trained personnel, who are also familiar with the valid
standards.
The VISAM GmbH offers at request inexpensive training for the use of the here
described products.

1.1.3 Intended Use

The systems are delivered from factory with the specific use case and with a
dedicated hardware and software configuration. Alterations are only allowed in
the context of the in the documentation featured possibilities. All other changes
to the hardware or software and the non-conforming use of the systems nullify
the liability of VISAM GmbH.

1.1.4 License Agreement

The usage of all in this documentation described programs and program parts
are subject to the VBASE license agreement.

6 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

1.2 Range of validity

This document provides a general description, in conjunction with certain
hardware and/or software. Note the latest and detailed descriptions
accompanying the products!

1.3 Used symbols

Note

Information that should be noted to ensure a faultless and
effective operation.

Hint
Tips and hints for the efficient use of the system respectively
system optimization.

ESD
Warning of damage to the systems / components by electrostatic
discharge. Precautions should be taken when handling
electrostatically sensitive components.

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 7

HB_VTPBC_70_100v1.0e_FINAL
.doc

2 Introduction

2.1 Regarding this document

This manual is intended to clarify the use of the VISAM TouchPanel devices
(„VTP“). In this document the device specific setting and possibilities are
described.
The handling of the on this device installed VBASE HMI/SCADA software is
described in a separate description.

2.2 The Article – and Model number

At this point a brief commentary on the article and model numbers of these VTP
series is given.
The model number is rather general and serves as a rough identification of the
VTP. The model number provides information about the operation system, the
display size and the built-in version of the VTP.
The article number however contains even more information. In the following
figure, the part of the article number is further explained.

Figure 1 The Information of the article number

8 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

3 Specification

3.1 System data

VTP-BC70 / BC100
Processor (CPU): ARM Cortex A8, 600MHz
RAM: 256MB DDR2 SDRAM onboard
Data memory: 512MB SLC onboard, 128KB FRAM for data backup
LAN: Intel 10/100 Base-T Ethernet controller, IEEE 802.3
Watchdog Timer: EC watchdog timer, 1.0 second timeout period

3.2 Interfaces

VTP-BC70/ BC100
Serial interface: 10/100 Base-T Ethernet,

RS-232/422/485 (COM1, D89) x 1, RS-422/485 (COM2, 4-Pin connector) x 1,
RS-485 (COM3, 2-Pin connector)

USB: 1 x USB 2.0 (Client), 1 x USB 2.0 (Host)
Extensions: 1 x Micro-SD Memory Card Slot

3.3 LCD Display

VTP-BC70
Size: 7“ WVGA TFT LCD
Brightness: 500 cd/m²
Viewing angle: 140°/120° (H/V)
Contrast ratio: 700:1
Resolution: 800 x 480 Pixel



VTP-BC100
Size: 10,1“ WSVGA TFT LCD
Brightness: 550 cd/m²
Viewing angle:140°/110°
Contrast ratio: 500:1
Resolution:1024 x 600 Pixel

All
MTBF (Backlight): 50000 hours
Maximum amount of colors: 64.000
Backlight: LED

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 9

HB_VTPBC_70_100v1.0e_FINAL
.doc

3.4 Touchscreen

Type: 5- wire, analog resistive
Translucent: above 80%

Lifespan: 36 million touches (with a silicon pen)

3.5 Power Supply

Supply voltage: 24 VDC
Electricity demand (maximum): 7 W (VTP-BC 70) / 9 W (VTP-BC 100)

3.6 Integrated Software

Operation system: Microsoft Windows Embedded CE 6.0 R3
HMI/SCADA: VBASE Compact-RT

The integrated software is embedded software that may be only operated on the
delivered hardware system!

3.7 Interface Arrangement

The arrangements of the interfaces are depicted in the following figures:

Figure 2 Interface Arrangement VTP-BC 70

10 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

Figure 3 Interface Arrangement VTP-BC 100

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 11

HB_VTPBC_70_100v1.0e_FINAL
.doc

3.8 Connection Assignment

3.8.1 Power Supply

Figure 4 Plug Power Supply

3.9 Power Switch

VTP-BC70 and VTP-BC100 do not have power switches.

3.10 Environment Conditions

Environmental Temperature (while operating): -20 ~ 60°C
Storage Temperature: -30 ~ 70 °C
Humidity: 40°C @ 10 ~ 90% relative (non condensing)
Vibration Resistance: 1 Grms (in average and while operating with a HDD)

3.11 Safety

Safety front side: IP66 / BSMI, CCC, FCC, UL

12 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

4 Software-Settings

4.1 Setup / Changing of the network (IP)-address

To change the network-address of the device, follow these instructions:
Open the windows start-menu << Settings. Select the point “Network and Dial­Up Connections”.

Figure 5 Windows Start-menu

Figure 6 Connection

Here open the property of the network card by a double click on its name, here
„IAG81681.

Figure 7 Ethernet-Setup

In the now opened property-window insert the desired network „IP-address“,

„Subnet Mask“, and if needed the „Default Gateway“. In the second tab „Name
Server“ the IP-address of the „DNS-Server“ and the „WINS-Server“ can be
inserted. Confirm the input by clicking on „OK“ (top right). Close the window
„Network and Dial-Up Connections“.

Save your settings by saving the „Registry“ as described in the
following section!

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 13

HB_VTPBC_70_100v1.0e_FINAL
.doc

4.2 Save changes to settings permanently

If you make changes in the area of the operating system (e.g. network- or
display-settings) please note that after each change, the registry file „Registry“
must be saved. f not, all changes are lost at the shutdown respectively
restart of the device!

The tool for the permanent saving of the registry “Registry Saver” can be found
in the Start-Menu >>”Programs” >> “Tools”.

Figure 8 Registry Saver

After saving the registry a confirmation is shown by the program.

Figure 9 Confirmation about saving of the registry

4.3 Automatic Startup of the HMI-Application

The VBASE-HMI-runtime environment (VOK) starts automatic after starting and
booting of the device.
Was the HMI-Application and as such the runtime environment shutdown, it can

be restarted with the help of the icon “START HMI” respectively by selecting it

from the Start-Menu > “Programs” without having to restart the whole device.

The runtime environment with all accessories is located (ex-factory) in the
directory:
"\HardDisk\VOK\"

4.4 FTP-Server, Data Transmission

The device features an integrated FTP-server which enables a simple data
transfer with the device.
Please note that the FTP-Server is configured ex-factory in a way that after
inputting username and password, full access to the device is granted.
To restrict the accesses respectively to secure the device against unauthorized
usage, the on the device installed VTP-Tool (see section 4.10) can be used.

The default settings ex-factory are:
IP-Address: Default = DHCP (the device tries to retrieve an IP-address from
the DHCP-server).
User: admin

14 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

Password: visam
FTP-Directory: /Harddisk/

The FTP-Server is also used by the VBASE-Editor for the transmission of projects
and the setup of the device (see Help-system of the editor).

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 15

HB_VTPBC_70_100v1.0e_FINAL
.doc

4.5 Touchscreen Calibration

It is possible to recalibrate the Touchscreen controller of the VTP from time to
time. A recalibration is needed if the mouse cursor is not displayed at the touch
point, but at a different position.

To calibrate select from the Start-Menu: „Settings“ >> Control Panel and then
the program „Stylus“.

A window with two tabs opens.

Figure 10 Touchscreen Calibration

Double-Tap – setting up the double-click speed
Calibration – to recalibrate the touchscreen

Follow the instructions on the screen and touch the corresponding calibration
points successively on the touchscreen.

Save your settings by saving the „Registry“ as described in the
section „Save Changes to settings permanently”!

16 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

4.6 Remote control of the device via network

To remote control the device for a comfortable setup and maintenance, the
application „VNC-Server“ is available. Ex-factory the license-free tool “Efon VNC”
is installed on the device.

On the PC-system from which you want to connect to the panel, a compatible
VNC-Viewer (e.g. UltraVNC, VNCviewer) must be installed and a network
connection must be established

Ex-factory the VNC-Server is provided with a default-password („visam“). At the
connection establishment the password will be queried.

Figure 11 VNC-Connection Establishment Remote Control

After the successful connection establishment the surface of the device can be
used in a window (the VNC-Viewer) on the PC-system.

Figure 12 Remote-Desktop

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 17

HB_VTPBC_70_100v1.0e_FINAL
.doc

Within this window the VTP (depending on the settings of the VNC-connection)
can be remotely controlled with the mouse and the keyboard.

The password and additional settings for the VNC-Server respectively the VNC­Connection can be changed according to your needs with the help of the
program „vncconfig“. The VNC-Server is configured ex-factory that you don’t
need to make any changes. The program “vncconfig” can be found in the Start­Menu >> „Programs“ >> “Tools”.

Figure 13 VNC-Server Einstellungen

The password of the VNC-Connection can be changed by clicking the button

„Configure“ (see Figure 12).

Save your settings by saving the „Registry“ as described in the
section „Save Changes to settings permanently”!

18 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

4.7 Connect network share

A VTP can be connected to a PC-system respectively a server in a network to
directly transmit data to these (e.g. Journaling).

To connect the VTP with a shared drive or directory on a tot he network
connected system, proceed as follows:

Select in the Start-Menu >> „Programs“ >> „cmd“.

Figure 14 Prompt

Enter here the following commands:

"net use share-name \\servername\share /user:<user>
/password:<password>"

„share-name“ – represents individual used name for the share.

„\\servername\share“ – describes the share on a distant device.

„<user>“ – represents the name of the user, who has the authorization to use

the share.

„<password>“ – Represents the password which is used for the user that has
the authorization to use the share.

After the successful input the share can be found "My Device" >> "Network" >>
"share-name".

Save your settings by saving the „Registry“ as described in the
section „Save Changes to settings permanently”!

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 19

HB_VTPBC_70_100v1.0e_FINAL
.doc

4.8 Additional Settings in Windows CE

The installed operating system allows a series of additional settings which will
not be considered in this description.

Always save your settings by saving the „Registry“ as described in
the section „Save Changes to settings permanently”!

4.9 Tools

In the menu „programs“ – „Tools“ some helpful programs can be found:

Figure 15 Tools in the menu "Tools"

4.9.1 The Tool CE NotepadPlus

„CE NotepadPlus“ is a simple text editor for Windows CE.

4.9.2 The Tool cmd

„cmd“ provides the prompt of the operating system Windows.

4.9.3 The Tool control

„control“ opens the settings-directory of the operating system Windows CE.

4.9.4 The Tool Registry Saver

„Registry Saver“ saves he registry (see chapter 4.2).

4.9.5 The Tool vncconfig

„vncconfig“ opens the configuration of the VNC-Server (see also chapter

4.6).

4.9.6 The Tool Wordpad

„Wordpad“ is the Microsoft Text Editor for Windows CE.

4.9.7 The Tool Resolution Utility

With the tool “Resolution Utility” the display resolution, the refresh rate

and if the screen should be rotated can be set with this tool.

20 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

4.10 VTP Tool

4.10.1 General

With the „VTP Tool“ a tool is provided that can adjust a series of system-settings
on your VTP.

In the following chapter the possibilities of these programs are described.
beschrieben.

Always save your settings by saving the „Registry“ as described in the
section „Save Changes to settings permanently”!

To open the program double-click the symbol „My Device“ on the desktop of the
VTP. In the now open window double-click on the symbol “HardDisk”. In the next
view the program “VTP Tool” can be found and opened by double-clicking. After
starting the program the following surface appears:

Figure 16 VTP Tool Start Picture

In the top area of the program window five tabs are lined up, which contain the
different setting options.
By clicking the corresponding tab the view changes accordingly.
As in the figure 15 depicted the other tabs cannot be completely displayed. But
the tabs can be moved by clicking the small arrows in the top right.

Requirements for the functionality of the VBASE-runtime environment:

The following settings should not be changed at all. They are part requirements
for the VBASE-project transmission from and to the VBASE-runtime environment
(VOK).
Firstly, the FTP-Server must be activated that a VBASE-project (files) from the
VBASE-Editor can be transmitted to the VTP or vice versa. On the other hand the
Telnet-Server must be activated. This is necessary so that the VBASE runtime
environment can be stopped by the VBASE-Editor for example before
transmitting a VBASE project and subsequently be restarted.

At the delivery of the VTP the FTP-Server and the Telnet-Server are both
activated with all options. The FTP-Server has also a default directory specified.
This is the directory which is accessed by default when connecting via a FTP­Connection (even anonymous, if this option is checked). This directory must

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 21

HB_VTPBC_70_100v1.0e_FINAL
.doc

contain the folder “VOK”. Both connection types can be specified, if they can be
processed password-protected or anonymous. If you decide to password-protect

the connections (the option „Use user login“ must be activated) ensure that the

corresponding user have the required authorizations. In this case it is advised to
deactivate the option for the anonymous access to the FTP-Server.

4.10.2 User / Rights

This tab features the user administration for your VTP. Here you have the
possibility to create new user, change user authorizations or to delete user. To
change the password of an user, create the user another time but enter another
password. The settings for the user remain. The user „admin“ is already created

at delivery. The password for the user „admin“ is „visam“. So the user „admin“ is

already shown in the list (see figure 15).

Add user:
To add a new user click on the button „Add User“. Another window opens up in
which the new user-name and the corresponding password can be entered. (see
figure 16). Note that the user password will be displayed in clear text.
As soon as you click in one of the input fields a small window with a desktop­keyboard appears - the „Input Panel“. With the help of this keyboard you can
directly process the inputs on the VTP if you do not remotely control the device.

Figure 17 VTP Tool - Creation of a new user and the "Input Panel"

Confirm your inputs by clicking on the button “Add User”. The window will be
closed and the new user will be inserted in the first place of the list (see figure

17). Additionally the home directory (“\Harddisk\“) will be inserted
automatically. This directory is the default directory on the VTP on which the
user has access via the FTP-connection. At this point the access can be restricted
to another directory.

Change of user authorizations:
To change the authorizations of a user the corresponding user must be selected
by double-click from the entry of the list. The selected user is then displayed
with a black frame (see red highlight in figure 17). Now the authorizations of this
user can be changed. It can be determined if this user has access has access to
the VTP via FTP- or Telnet-connection. The setting of these authorizations
respectively their functionality require the activation of the Telnet- respectively
the FTP-server on the VTP (see chapter 4.10.3 and 4.10.4). If the user was
granted access via FTP-connection, the input field „Home directory“ must be

22 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

edited to the directory to which the user should have access to. The default­home directory („\Hardisk\“) is automatically inserted when creating a new user.
This entry can be changed according to your needs. By clicking into the input
field the „Input Panel“ will be shown, to directly allow inputs on the VTP.
Additionally the access authorizations of the FTP-connection of the user can be

restricted. Thereby the option “FTP read” means a read-access to the home
directory. The option “FTP write” allows the user to write files into the home­directory and to change or delete existing files. If the option “hidden files” is

checked, the user can see all hidden system-files in this directory and is able to
change and/or delete them.

Figure 18 VTP Tool - Change of user authorization

Delete user:
To delete a user the corresponding user must be selected with a double-click
from the entry in the list. The selected user will then be displayed with a black
frame (see red highlight in figure 17). Now click on the button “Delete user”. The
corresponding user will be deleted from the list.

4.10.3 FTP-Server

Figure 19 VTP-Tool FTP-Server settings

In this tab the „global“ settings for the FTP-server can be determined. The first
option activates – if checked – the FTP-server on this VTP. This and the fourth

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 23

HB_VTPBC_70_100v1.0e_FINAL
.doc

option are prerequisites that user, which were granted FTP-access, can properly
use these authorization.
The second options allows an anonymous user to establish a FTP-connection to
the below stated default-directory. Neither a user name nor a password must be
specified.
The third option allows an anonymous user to write files into the default­directory.
The fourth option allows besides an anonymous FTP-connection to the default­directory also the FTP-connection to the home-directory with a corresponding
user login.
The entry in the input field „Default-directory“ determines the directory to which
an anonymous user has access to.

24 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

4.10.4 Telnet-Server

Figure 20 VTP Tool Telnet-Server settings

In this tab the „global“ settings for the Telnet-server can be edited. The first
options - if checked – activates the Telnet-server on this VTP. This option allows
the Telnet-access to the VTP without specifying any user information. This
function is required to start or stop the VBASE-runtime environment (VOK) via
the VBASE-editor
The second option restricts the access to the VTP via Telnet to the users, that
have the corresponding authorization for the Telnet-access. If this option is
checked, a user login is required for the Telnet-access.

4.10.5 Display Settings

For display settings see chapter 4.9.7 (“Resolution Utility”)

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 25

HB_VTPBC_70_100v1.0e_FINAL
.doc

5 Appendix

5.1 Fuse

These VTP are protected against electrical damage by a fuse.

The fuse cannot be changed readily, as trained personnel is required.

The fuse is triggered if a voltage > 32VDC is applied.

26 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

5.2 PIN-Assignment of the serial interface

5.2.1 Serial interface RS-232/422/485 (COM1)

Figure 21 RS-232/422/485(COM1)

5.2.2 Serial interface RS-422/485 (COM2) / RS-485 (COM3)

Figure 22 RS-422/485 (COM2) RS-485 (COM3)

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 27

HB_VTPBC_70_100v1.0e_FINAL
.doc

5.2.3 USB Verbindung

Figure 23 PIN Assignment USB-connection

28 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

5.3 Dimension and Cutout

5.3.1 Weight (VTP-BC70 / 100)

Weight: 1 kg / 1,2 kg

5.3.2 Cutout

VTP-BC 70
Dimension: 203 x 150 x 44 mm (width x height x depth)
Cutout: 192 x 138,5 mm
Maximum mounting panel thickness: < 6mm

VTP-BC 100
Dimension: 272 x 214 x 43 mm (width x height x depth)
Cutout: 260 x 201,5 mm
Maximum mounting panel thickness: < 6mm

Figure 24 Panel mounting

V I S A M T O U C H P A N E L V T P - BC70 / 100 - 29

HB_VTPBC_70_100v1.0e_FINAL
.doc

Figure 25 Dimension VTP-BC 70

Figure 26 Dimension VTP-BC 100

30 – V I S A M T O U C H P A N E L V T P - B C 7 0 / 100

HB_VTPBC_70_100v1.0e_FINA
L.doc

5.4 Illustration Directory

Figure 1 The Information of the article number .............................................. 7

Figure 2 Interface Arrangement VTP-BC 70 ................................................... 9

Figure 3 Interface Arrangement VTP-BC 100 ............................................... 10

Figure 4 Plug Power Supply ....................................................................... 11

Figure 5 Windows Start-menu ................................................................... 12

Figure 6 Connection ................................................................................. 12

Figure 7 Ethernet-Setup ........................................................................... 12

Figure 8 Registry Saver ............................................................................ 13

Figure 9 Confirmation about saving of the registry ....................................... 13

Figure 10 Touchscreen Calibration ............................................................. 15

Figure 11 VNC-Connection Establishment Remote Control ............................. 16

Figure 12 Remote-Desktop ....................................................................... 16

Figure 13 VNC-Server Einstellungen ........................................................... 17

Figure 14 Prompt ..................................................................................... 18

Figure 15 Tools in the menu "Tools" ........................................................... 19

Figure 16 VTP Tool Start Picture ................................................................ 20

Figure 17 VTP Tool - Creation of a new user and the "Input Panel" ................. 21

Figure 18 VTP Tool - Change of user authorization ....................................... 22

Figure 19 VTP-Tool FTP-Server settings ...................................................... 22

Figure 20 VTP Tool Telnet-Server settings ................................................... 24

Figure 21 RS-232/422/485(COM1)............................................................. 26

Figure 22 RS-422/485 (COM2) RS-485 (COM3) ........................................... 26

Figure 23 PIN Assignment USB-connection .................................................. 27

Figure 24 Panel mounting ......................................................................... 28

Figure 25 Dimension VTP-BC 70 ................................................................ 29

Figure 26 Dimension VTP-BC 100 .............................................................. 29