Visa Lighting Sole Series, Sole CB1852, Sole CB1850 Installation Instructions Manual
INSTALLATION INSTRUCTIONS
Model:
CB1850, CB1852
Fixture Family:
Document Description: Installation Instructions for
SOLE
Sole Series Mirrors
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting 2016
Drawing:
762277XX
SOLE
Rev:
F
CB1850 - RECTANGULAR
PAGE 2, 3, and 4
CB1852 - OVAL
PAGE 5, 6, and 7
Sheet:
1 of 9
Eng:
CG2
Date Drawn:
10/27/19
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.
•
Make sure all connections are in accordance with the National Electrical Code and local regulations.
•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
•
Service should be performed by qualified personnel.
•
!
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
•
INSTALLATION INSTRUCTIONS
Model:
CB1850, CB1852
Fixture Family:
Document Description: Installation Instructions for
SOLE
Sole Series Mirrors
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this illuminated mirror.
WARNING:
* To reduce the risk of burns, fire, electric shock, or injury to persons:
* When using an electrical furnishing, basic precautions should always be followed, including
the following:
*Use this illuminated mirror for its intended use as described in these instructions. Do not
use attachments not recommended by the manufacturer.
WARNING:
* Risk of Death or Serious Injury
* Do not install near pools, ponds, or other bodies of water.
Drawing:
762277XX
Rev:
F
WARNING
:
To reduce risk of Ligature:
* Ensure all fasteners are fully seated and do not protrude from the mirror frame.
* Apply a pickproof sealant around the perimeter of the frame in the slight gap
between the frame and mounting substrate.
Sheet:
2 of 9
Eng:
CG2
Date Drawn:
10/27/19
SAVE THESE INSTRUCTIONS
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.
•
Make sure all connections are in accordance with the National Electrical Code and local regulations.
•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
•
Service should be performed by qualified personnel.
•
!
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
•
INSTALLATION INSTRUCTIONS
Model:
CB1850, CB1852
Fixture Family:
Document Description: Installation Instructions for
SOLE
Sole Series Mirrors
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this illuminated mirror.
GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system, or an
equipment grounding conductor must be run with the circuit conductors and connected to the
equipment grounding terminal or lead on the product. Electrical Ratings: 120-277 VAC,
50/60Hz, 50 W MAX
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
Drawing:
762277XX
Rev:
F
CLEANING AND CARE INSTRUCTIONS
Use care when cleaning this LED Luminaire. The mirror is made of polycarbonate. Do not use
abrasive cleaners, chemicals or solvents which may result in surface damage to lens or housing.
The luminaire can be cleaned by hose-directed water spray to remove any dust or debris. If
necessary, use mild soap with warm water for cleaning the exterior surfaces of this fixture.
Sheet:
3 of 9
Eng:
CG2
Date Drawn:
10/27/19
SAVE THESE INSTRUCTIONS
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use.
•
Make sure all connections are in accordance with the National Electrical Code and local regulations.
•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
•
Service should be performed by qualified personnel.
•
!
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
•
Loading...