Visa Lighting MIDBAY Series Installation Instructions Manual

INSTALLATION INSTRUCTIONS

MIDBAY

Model:
Fixture Family:
Document Description: Installation Instructions for

MIDBAY

MIDBAY Series Luminaires

LENS ATTACHMENT, JBOX MOUNTING AND ACCESS

1717 West Civic Drive Milwaukee, WI 53209

Design Modification Rights Reserved

414-354-6600

© Visa Lighting

MOUNTING
SCREWS

1. ANGLE FIXTURE JBOX THROUGH NOTCHED
AREA IN HOUSING AND SLIDE INTO POSITION
SO THAT JBOX MOUNTING FLANGE IS UNDER
HOUSING EDGE AND SCREW HOLES ARE ALIGNED.

2. ATTACH WITH (4) SCREWS PROVIDED THROUGH
HOUSING INTO JBOX FROM TOP AS SHOWN.

3. REMOVE ACCESS PLATE FOR MOUNTING
AND WIRING BY LOOSENING SCREWS (2),
THEN TURN AND SLIDE PLATE TO THE SIDE.

4. MOUNT AND WIRE PER PAGE 2 AND 3.

5. LENS IS ATTACHED BY LIFTING INTO FIXTURE
AND SECURING WITH ATTACHMENT NUT
AGAINST LENS STOPS.

BRACKET
MOUNTING
SCREWS

WIREGUARD
BRACKET

FIXTURE JBOX

NOTCHED AREA

LENS

WIREGUARD
MOUNTING
NUT

LENS STOP

FIXTURE

760635XXDrawing: DRev:

ACCESS
PLATE

1 of 3Sheet:

LENS ATTACHMENT
NUT

MAREng: 4/20/2005

FIXTURE

MOUNTING
LEG

WIREGUARD

When using electrical equipment, basic safety precautions should always be followed, including the following:

Read all instructions carefully installing and save for future use.•
Make sure all connections are in accordance with the National Electrical Code and local regulations.•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture•
Service should be performed by qualified personnel.•

•

These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

!

WIREGUARD MOUNTING

1. INSTALL ONE NUT ONTO EACH MOUNTING
LEG OF WIREGUARD (3 PLACES). TURN NUT TO
THE END OF THE THREADS.

2. ASSEMBLE WIREGUARD BRACKETS TO
FIXTURE BY INSERTING INTO SLOT ON HOUSING
AND ATTACHING WITH (2) MOUNTING SCREWS.

3. LIFT WIREGUARD AROUND FIXTURE AND INSERT
MOUNTING LEGS THROUGH HOLES IN BRACKET.
ATTACH WITH 3 ADDITIONAL NUTS.

Date Drawn:

INSTALLATION INSTRUCTIONS

MIDBAY

Model:
Fixture Family:
Document Description: Installation Instructions for

JBOX (BY
OTHERS)

MIDBAY

MIDBAY Series Luminaires

FIXTURE JBOX

1717 West Civic Drive Milwaukee, WI 53209

Design Modification Rights Reserved

414-354-6600

© Visa Lighting

SURFACE MOUNTING

1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING AND JBOX ACCESS INSIDE
FIXTURE. ASSEMBLE CLOSURE PLATE TO FIXTURE
JBOX WITH SCREWS (2) PROVIDED WHEN USING
A 4" OCTAGONAL BOX.

2. MAKE ELECTRICAL CONNECTIONS PER CODE.

760635XXDrawing: DRev:

JBOX
(BY OTHERS)

JBOX ( BY OTHERS)

LOOPED/CRIMPED
CABLE ENDS

CABLE MOUNTING
DETAIL

CHAIN
MOUNTING
DETAIL

LOOP CONNECTOR

JBOX PLATE &
HOOK OPTION
(ORDERED
SEPARATE)

LOOP
CONNECTOR

FIXTURE JBOX

JBOX PLATE &
HOOK OPTION
(ORDERED
SEPARATE)

CABLE
ASSEMBLY

FIXTURE JBOX

HOOK MOUNTING

1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING AND JBOX ACCESS INSIDE
FIXTURE. MAKE ELECTRICAL CONNECTION AT
FIXTURE.

2. ASSEMBLE LOOP CONNECTOR TO EYEBOLTS AT
FIXTURE AND JBOX PLATE, CLOSE LOOP AND
ATTACH TO STRUCTURE. (JPH OPTION CAN BE
ORDERED SEPARATE FOR ATTACHMENT TO
JBOX)

3. MAKE ELECTRICAL CONNECTIONS PER CODE.

CABLE / CHAIN MOUNTING

1. ASSEMBLE FIXTURE JBOX TO FIXTURE WITH
SCREWS (4) PROVIDED. SEE PAGE 1 FOR
JBOX MOUNTING AND JBOX ACCESS INSIDE
FIXTURE. MAKE ELECTRICAL CONNECTION AT
FIXTURE.

2. LOOP CABLE THRU EYEBOLTS (3) ON FIXTURE
AND ATTACH CABLE GRIPPER TO CABLE PER
INSTRUCTIONS IN CABLE ASSEMBLY PACKAGE.
FOR CHAIN MOUNTING, USE (3) LOOP
CONNECTORS TO ATTACH CHAIN TO FIXTURE
EYEBOLTS. (SEE DETAILS).

3. ASSEMBLE ALL CABLES OR CHAINS TO LOOP
CONNECTOR, ATTACH TO STRUCTURE AND
CLOSE LOOP. (JPH OPTION CAN BE ORDERED
SEPARATE FOR ATTACHMENT TO JBOX)

4. MAKE ELECTRICAL CONNECTIONS PER CODE.

5. IF DESIRED, ROUTE CORD ALONG THE CABLE/
CHAIN AND SECURE EVERY 6".

2 of 3Sheet:

MAREng: 4/20/2005

Date Drawn:

When using electrical equipment, basic safety precautions should always be followed, including the following:

Read all instructions carefully installing and save for future use.•
Make sure all connections are in accordance with the National Electrical Code and local regulations.•
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture•
Service should be performed by qualified personnel.•

•

These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.

!