Visa Lighting Linesse CV2424 Installation Instructions Manual
Linesse Linear Luminaire
3” Recessed
Installation Instructions
1717 W Civic Drive, Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© 2018 Visa Lighting
LINESSE LINEAR LUMINAIRE
3” RECESSED
CV2424
Page 2: Warnings
Page 3: Mounting Types and Dimensions
Page 4: T-Grid and Joining Fixtures
Page 5: Hard Ceiling and Joining Fixtures
Page 7: Corners
Page 8: Corners – T-Grid and Joining Fixtures
Page 9: Corners – Hard Ceiling and Joining Fixtures
Page 10: Power Feed
When using electrical equipment, basic safety precautions should always be followed, including the following:
•Read all instructions carefully before installing and save for future use.
•Make sure all connections are in accordance with the National Electrical Code and local regulations.
•To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
•Service should be performed by qualified personnel.
!
•These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
1
Model: CV2424
Linesse Linear Slot
Publication: 762302XX
Document Description: Installation Instructions
for 3” Linesse Linear Recessed
Series Luminaires
1717 W Civic Drive, Milwaukee, WI 53209
Design Modification Rights Reserved
WARNING
To reduce the risk of death, injury or property damage
from fire, electric shock, cuts, abrasions, falling parts and other hazards:
• Installation and maintenance must be performed by a person familiar with the construction and
operation of this product and any hazards involved. All applicable codes and ordinances must be followed
• Read this document before installing, servicing or maintaining this equipment. These instructions do
not cover all installation, service and maintenance situations. If your situation is not covered, or, if you
do not understand these instructions or additional information is required, contact your distributor
Before installing, servicing or maintaining this equipment, follow these general precautions.
To reduce the risk of electrocution:
• Make sure the equipment is properly grounded
• Always deenergize the circuit and/or equipment before connecting to, disconnecing from or servicing
the equipment
To prevent luminaire row from over-current:
• By adding the input current of each luminaire section marked on the luminaire, the total current per
power feed must not exceed the maximum line wire amperage marked on the luminaire and the power
feed cord/wire amperage rating whichever is the least
To reduce the risk of fire:
• Use supply conductors with a minimum installation temperature rating as specified on equipment
To reduce the risk of personal injury from cuts, abrasions or falling parts:
• Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton, handling
and maintaining this equipment
• Do not use abrasive materials, glass cleaners or other solvents on reflector or lens. These substances
may damage equipment and cause parts to eventually break and fall
• Do not install a damaged fixture
414-354-6600
© 2018 Visa Lighting
When using electrical equipment, basic safety precautions should always be followed, including the following:
•Read all instructions carefully before installing and save for future use.
•Make sure all connections are in accordance with the National Electrical Code and local regulations.
•To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
•Service should be performed by qualified personnel.
!
•These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
2
Model: CV2424
Linesse Linear Slot
Publication: 762302XX
Document Description: Installation Instructions
for 3” Linesse Linear Recessed
Series Luminaires
MOUNTING TYPES AND DIMENSIONS
1717 W Civic Drive, Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© 2018 Visa Lighting
Flange Flangeless/Trimless 9/16” Grid
Tegular Lay-in
“Rough In” Width
Mounting Type 3” 4”
Flange 3-5/8” 4-5/8”
Flangeless/Trimless 3-5/8” 4-5/8”
Ceiling Type 3” 4”
9/16” Tegular/Lay-in 3-13/16” 4-13/16”
15/16” Tegular/Lay-in 4-1/8” 5-1/8”
9/16” Grid
Slot
Grid Mounting Center Widths
9/16” Slot 4” 5”
15/16” Grid
Tegular Lay-in
3-11/16”
Rough-In Width Grid Width
When using electrical equipment, basic safety precautions should always be followed, including the following:
•Read all instructions carefully before installing and save for future use.
•Make sure all connections are in accordance with the National Electrical Code and local regulations.
•To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
•Service should be performed by qualified personnel.
!
•These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
3
Loading...