ViSAGE VIS122 Instruction Manual

MINI-BEAMWASH Page 1

MINI-BEAMWASH

(VIS122)

GB - INSTRUCTION MANUAL

MINI-BEAMWASH Page 2

Thank you for having chosen our VISAGE LED EFFECT. For your own safety, please read this user manual carefully
before installing the device.

SAFETY INTRODUCTION

• If the device has been exposed to temperature changes due to environmental changes, do not switch it on
immediately. The arising condensation could damage the device. Leave the device switched off until it has reached
room temperature.

• It is essential that the device is earthed. A qualified person must carry out the electric connection.

• Make sure that the available voltage is not higher than stated at the end of this manual.

• Make sure the power cord is never crimped or damaged. If it is damaged, ask your dealer or authorized agent to

replace the power cord.

• Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord
by plug. Never pull out the plug by tugging the power cord.

• DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.

• Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that
their effectiveness is impaired, for example by cracks or deep scratches.

• The lamp shall be changed if it has become damaged or thermally deformed

CAUTION:

1. Be very careful during installation. Since you will be working with a dangerous voltage you can suffer a life­threatening electric shock when touching live wired.

2. Never look directly into the light source, as sensitive persons may suffer an epileptic shock.

3. Please be aware that damages caused by manual modifications to the device are not subject to warranty. Keep
away from children and non-professionals.

4. The light doesn’t include any spare parts for repair, please check if all the parts are well installed and screws are
fitted tightly before operating. Do not use the light when the cover is open.

GENERAL GUIDELINES

• This device is only allowed to be operated with an alternating current of max. 100-240VAC/50-60Hz and was
designed for indoor use only.

• Do not shake the device. Avoid brute force when installing or operating it.

• When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture

or dust. The minimum distance between light-output from the projector and the illuminated surface must be more
than 1 meter. Keep a distance to any flammable objects of at least 5m.

• Operate the device only after having familiarized yourself with its functions. Do not permit operation by person not
qualified for operating the device. Most damages are the result of unprofessional operation.

• Please use the original packaging if the device is to be transported.

• For safety reasons, please be aware that all modifications on the device are forbidden. Furthermore, any other

operation may lead to short-circuit, burns, electric shock, lamp explosion, crash, etc. If this device will be operated
in any way different to the one described in this manual, the product may suffer damages and the guarantee
becomes void.

GB

MINI-BEAMWASH Page 3

MOUNTING Orientation

This fixture may be mounted in any position, provided there is adequate room for ventilation It
is important never to obstruct the fan or vents pathway.
When selecting installation location, take into consideration lamp replacement access and routine maintenance.
Safety cables must always be used.
Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature changes or
restricted ventilation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or his service agent or a similar qualified person in order to avoid a hazard.
Make sure the installation position is stable before you fix the light. When the light is reverse hanging, make sure the
light will not fall from the truss, use the safety cable go through the truss and bracket of the light as a supporting, to
avoid the light to fall down. There is no entrance to the work area during mounting. Periodically check if the safety
cable has fretted away or clamp is loosened. We will not take any responsibility for damages caused by a badly
installed unit.

Power Supply and Signal Cable Connection

1. Mains Power connection

The exclusive plug should be used between the connection of unit and power. Please ensure that the rated voltage
and frequency are accordance with the power supply. The required input voltage and frequency are: 100-240Vac –
50-60Hz
We suggest that every light has an independent switch so that you can turn on or turn off the light randomly. Note:
the ground wire (yellow/green double-colour wire) must be safely connected, the electrical installation must be in
accordance with the related standards
CAUTION: When installing the device, make sure there is no highly inflammable material within a distance of min.5m!

2. Connection of Signal Cable

You can use the 3-pin XLR cable to connect the output socket of the master and the input socket of the slave light.
Connect the DIGITAL OUT socket of the master and the IN socket of the slave light, then, connect the OUT socket
to the IN socket of the next light. Ordinal to connect all the lights as below:

The connection between the output of master and input of product, it’s available to use the 3 pins XLR cable which

provided by the manufacturer. Signal cable from the DMX output of the controller to the input of the first master light,
and connect to the DMX input of second slave light from the DMX output of the first master light, analogously, till
connected all the slave lights, and insert the last connector to the output of the final light. (Notice: the diameter of
core of every cable should be 0.5mm at least, double core shelter cable should be used).The signal connecting must
use the attached 3 pins XLR cable. Notice, all the internal lead wire of the 3 pins XLR cable should not touch to each
other or connect to the connector.

A DMX signal terminator is recommended on the last unit of the chain. DMX terminator is a XLR connector with a
120Ω resistor between the pin 2 and pin 3 of the XLR connector

IN

OUT

IN

OUT

OUT

IN

3 1 2

MINI-BEAMWASH Page 4

DESCRIPTION MENU

To select any functions, press the MENU button until the required function is showing on the display. Select the
unction by pressing the ENTER button and the display will blink. Use the DOWN and UP button to change the mode.
Once the required mode has been selected, press the ENTER button to setup to go back to the functions without any
changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to
exit the menu mode.
The main functions are shown below:

1 ADDR

DMX Address

= A001---A512

2 CHND

DMX Mode

.=CH15

.=CH21

3 SLND

Run Mode

.=Master

.=Slave

4 SHND

Sound control

.=Sound

Auto run speed

.=sp0-sp9

5 SOUN

Sound Control switch

.=OFF

.=ON

6 SENS

Sound Control Sens

.=0

.=100

7 BLND

Standby mode

.=YES

.=NO

8 LED

Background lamp switch

.=OFF

.=ON

9 DISP

Display Reverse

.=YES

.=NO

10 PAN

X Reverse

.=YES

.=NO

11 TIL

Y Reverse

.=YES

.=NO

12 MANU

Manual test

= PAN

= TILT

= RED 1

= GREEN 1

= BLUE 1

= WHITE 1

= RED 2