ViSAGE VIS0481, VIS0492, VIS04921 Operating Instructions Manual

1 of 3 pages

VIS0481 LED Multipar 18 x 5 in 1 RGBAW Operation Manual

The 5IN1 LED Multipar provides an extremely powerful light source. Controlled via digital display

through the three buttons------MODE, UP, DOWN. It can function store when it is turned off, resuming this

program when turned back on. This product has a temperature protection function, turning off automatically if

the temperature exceeds 85°C.

A Specification:

1. Weight: 6.2kg

2. Size: 330 x 270 x220mm

3: Supply: AC 120V/240V, 60HZ/50HZ

4: Consumption: 165W max

5: LEDS: 18 x 10W (RGBWA 5 in 1)

6: Beam angle: 40°

7: 3PIN female XLR socket and 3PIN male XLR socket

8: Built-in microphone

9: LED digital display

10: IR remote available (VIS0499 available separately)

Operation modes are accessed via Mode button as follows (To make the display stay on constantly press the

MODE and UP buttons at the same time. To make the display turn off after 20 seconds, press the MODE and

DOWN buttons at the same time.)

1. Static colour select mode

Press“MODE ” button to select static colour program mode. The digital display reads “C.X X”. Press “UP” or

“DOWN” to select individual colours.

2. Colour snap mode

Press“MODE” button,to select colour snap change mode. The digital display reads “J.X X”. Press UP or

DOWN to select the change speed 1-99 (from slow to quick)

3. Colour fade mode

Press“MODE” button,select colour fade mode. The digital display reads “F.XX”. Press UP or DOWN to select

fade speed 1-99 (from slow to quick).

4. Auto-run mode

Press“MODE”button,to select auto mode. The digital display reads “A.- -” The colour snap change program and

colour fade program run alternatively. The UP or DOWN buttons have no effect in this mode - running speed is

determined by the current speed of colour snap and colour fade programs.

5. Sound-active mode

Press“MODE” button to select sound-active mode. The digital display reads “S.XX”. Press UP or DOWN to

select sound sensitivity from 0-31. 0 is off, 1 is the lowest sensitivity, 31 is the highest.

6. Slave mode

Press“MODE” button to select Slave mode. The digital display reads “S.L.A.”. The UP or DOWN buttons have

no effect in this mode.

7. DMX mode

Press MODE button to select DMX mode. The digital display shows DMX address“X X X”. Press UP or DOWN

to select DMX address.You can set 512pcs address. It will flicker when there is no controller signal.

2 of 3 pages

1) DMX mode

CH No. DMX VAULE FUNCTION

CH1 000~255 Red(dim→bright)

CH2 000~255 Green(dim→bright)

CH3 000~255 Blue(dim→bright)

CH4 000~255 White(dim→bright)

CH5 000~255 Amber(dim→bright)

000~189 Dimmer(dim→bright)

190~250 Flash(slow→fast)

CH6

251~255 No function

11.

Operation by IR remote:

You can also operate this product by IR remote, the maximum operating distance is 10M.

Select program Mode

Press PROG button to select static colour, snap change, colour fade or auto run mode. Each press of this button

will change to the next mode.

1. When the LED par goes into the static color select mode press “+” and “-” or button 1-9 to select the static

colours. You can also press FLASH to turn on/off flash and press “+”and “-” to adjust the flash speed.

2. When the LED par goes into the snap change mode, you can press SPEED to set the color change speed and

press “+”and “-” to adjust it. You can also press FLASH to turn on/off flash and press “+”and “-” to adjust the

flash speed.

3. When the LED par goes into the colour fade mode,you can press SPEED to set the fade speed and press “+”

and “-” to adjust it. You can also press FLASH to turn on/off flash and press “+”and “-” to adjust the flash speed.

4. When the LED par goes into auto run mode you can press FLASH to turn on/off flash and press “+”and “-”

to adjust the flash speed.

Sound Active Mode

Press SL/SA button to cycle between slave mode and sound active mode. Each press of this button will change

modes. When the the LED par goes into sound active mode, you can press “+” and “-” to adjust the sound active

sensitivity level.

M/S mode

Press SL/SA button to cycle between slave mode and sound active mode to choose slave mode. Each press of

this button will change modes.

Select light program mode

Press R/G/B/W/A to choose R/G/B/W/A colours, pressing “+” and “-” buttons to adjust the intensity of the

light. Press FLASH to turn on/off flash effect, pressing “+” and “-” buttons to adjust the flash speed.