Viper SL10BOX Owner's Manual

CONGRATULATIONS on your purchase of a Viper product,
and welcome to the V.I.P. family. We appreciate your
business and will do everything in our power to keep you
happy with your purchase for many years to come.

As part of the V.I.P. family, you are entitled to the best
protection by one of the most comprehensive warranties in the
industry.

Thank-you for purchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS

Machine Components 3
Safety Precautions 4
Machine Set Up 5
Machine Operation 5-6
Machine Maintenance & Storage 6-7
Troubleshooting 8
Parts Lists 9-17
Wiring Diagram 18

2

1

3

5

6

4

2

MACHINE COMPONENTS

1) Vacuum / pump on/off s witch

2) Recovery tank lid

3) Solution tank fill port

4) Pipe

5) Accessory tool solution hookup

6) Drain hose

3

SAFETY PRECAUTIONS

GROUNDING INSTRUCTIONS
General – This carped extraction machine
shall be grounded while in use to protect
the operator from electric shock. The
machine is provided with a three-contact
grounding type attachment plug to fit the
proper grounding type receptacle. The
green (or green & yellow) conductor in the
cord is the grounding wire. Never connect
this wire to other than the grounding pin of
the attachment plug.

This machine is for use on a nominal 120­volt circuit and has a grounding plug that
resembles the plug illustrated in figure
below. Make sure that the machine is
connected to an outlet having the same
configuration as the plug . No adapter
should be used with this machine.

This machine is intended for commercial
use. It is constructed for use in an indoor
environment and is not intended for any
other use. Use only recommended
accessories.

All operators shall read, understand and
exercise the following safet y pr ecautions:

1) Do not operate machine:

- Unless trained and authorized

- Unless you have read and
understand operators manual

- In flammable or explosive areas.

- With damaged or modified cord or
plug.

- If not in proper operating condition.

- In outdoor areas.

- In standing water.

- Without filters in place.

- With the use of unapproved extension
cords.

2) Before operating machine:

- Make sure all safety devices are in
place and operate properly.

3) When using machine:

- Mix and handle any chemicals
according to manufacturer’s
recommendations

- Do not run machine over cord.

- Do not pull machine by cord or plug.

- Do not pull cord around sharp edges
or corners.

- Do not unplug by pulling on the cord.

- Do not stretch cord.

- Do not handle plug with wet hands.

- Keep cord away from heated
surfaces.

- Do not pick up flammable materials
or reactive metals.

- Report machine damage or faulty
operation immediately.

4) Before leaving or servicing machine:

- Turn off machine.

- Unplug power cord from outlet.

5) When servicing machine:

- Unplug cord from outlet.

- Use manufacturer supplied or
approved replacement parts.

- Avoid moving parts. Don’t wear
loose clothing.

4

SLIDER EXTRACTOR SETUP

!!! Read operators manual thoroughly

prior to operating or servicing this

machine!!!

Carefully check the shipping carton for
signs of damage. Report any carton
damage to carrier immediately.

Check carton contents to ensure carton is
complete. Contact your Viper distributor if
anything is missing.
Contents:

• Carpet Extractor

• Short “bleeder ” vacuum hose

• 50’ extension power cable

• Vacuum and solution hoses

!!! Read operators manual

thoroughly prior to operating or

servicing this machine!!!

1) Using a hose or bucket, fill tank with a

maximum of 10 gallons of hot water.

2) Add distributor recommen de d cleaning

solution

!!! Do not use flammable liquids or

operate machine in or near

flammable liquids or vapors!!!

3) Connect the supplied extension power

cable to the machine. Plug cord into a
grounded wall outlet. (see grounding
instructions)

4) Attach vacuum and solution hoses to

appropriate connections on the

machine and your wand.. As yo u do
this, always inspect hoses for cracks or
fraying. Do not use if hose are cracked
of frayed.

MACHINE OPERATION

PRIOR TO EXTRACTING CARPETS

1) Inspect power cable and extension

cable for damage. Replace cable if
damage is found.

2) Vacuum carpet to remove debris prio r

to extracting carpet.

CARPET EXTRACTING

1) Turn on vacuum / pump switch.

2) To release spray, simply pull back on

your wand trigger.

OPERATING HINTS

1) Work away from power outlet and

power cable in order to avoid damage
to the power cable.

2) Continually check for foam buildup in

recovery tank. Use a distributor
recommended foam control solution.

NOTE: Excessive foam buildup will not
activate the float shut-off and may cause
damage to the vacuum motor.

3) Repeat extraction path on heav il y

soiled areas.

4) When recover of the dirty solution ends,

or the solution tank is empty, you must
drain the recovery tank. (se e TA NK
DRAINING)

USE OF ACCESSORY TOOLS

NOTE: Prior to cleaning upholstery, be
sure to read cleaning instructions provided
by the man u facturer .

1) Attach vacuum and solution hoses to

appropriate connections on the
machine.

2) Connect (optional) accessory tool to

solution and vacuum hoses.

5

3) Turn on vacuum / pump switch.

4) Operate accessory tools as needed.

5) When cleaning is completed, relieve

water pressure from solution lines by
turning off vacuum / pump switch and
then squeeze trigger for 4 seconds.

DRAINING TANKS

DRAINING SOLUTION TANK

1) Connect the “bleeder” vacuum hose

(included with machine) to the
vacuum inlet.

2) Remove the solution tank filter at the

fill area and place end of “bleeder”
hose into the bottom of the tank.

3) Turn on vacuum / pump switch &

vacuum out the remaining solution.

DRAINING RECOVERY TANK

1) Turn off machine, unplug and remove

power cable.

2) Unhook drain hose off the ba c k of the

machine and remove drain hose
stopper.

3) Drain dirty solution into floor drain.

4) Replace drain hose stopper and

reattach hose to back of machine.

MACHINE MAINTENANCE

To keep the machine performing well
for many years, please follow the
following maintenance procedures.

!!! Always confirm that the machine
is unplugged prior to performing
any maintenance or repairs!!!

DAILY MAINTENANCE

1) When cleaning operation is complete

for the day, drain and rinse the
recovery tank thoroughly with clean
water.

2) Remove remaining solution from

solution tank.

3) Remove float shut-off (ping pong ball

in cage) from recovery tank and clean
with water.

4) The filter located in the solution tank

need to checked and cleaned w he n
dirty in order for it to properly filte r
debris from the solutio n tank. if the
filter is missing or damaged it m ust be
replaced before the machine is used.

5) Clean machine with a nonabrasive

cleaner.

6) Inspect power cable for any damage.

Replace if necessary.

MONTHLY MAINTENANCE

1) Flush pump & plumbing with an acetic
acid solution to dissolve any chemical
buildup.
Mixing Instructions:

a) Premix 16 oz. or an acetic acid
solution with 2 gallons of water and
pour into solution tank.
b) Attach solution hose and wand
to machine.

c) Turn vacuum / pump switch on.

6