Page 1
MODEL # MB39CV
SERIAL #
VA41128
HAMILTON,MI 49419
VIPER NORTH AMERICA
[866] 41-VIPER
[866] 418-4737
P.O. BOX 104
Rev.00(08-08)
VIPER...exceptional
value
Page 2
CONGRATULATIONS on your purchase of a Viper product,
and welcome to the V.I.P. family. We appreciate your
business and will do everything in our power to keep you
happy with your purchase for many years to come.
As part of the V.I.P. family, you are entitled to the best
protection by one of the most comprehensive warranties in the
industry.
Thank-you for purchasing Viper products!
Tom Vander Bie, CEO
TABLE OF CONTENTS
Safety Precautions 3
Machine Operation 4
Machine Maintenance & Storage 4
Parts Lists 5-9
Wiring Diagram 10
Page 3
SAFETY PRECAUTIONS
!!! This machine must be grounded!
Grounding provides a path of least
resistance for electrical current. To
reduce the risk of electrical shock
should the machine malfunction, the
machine has a special grounding plug.
Do not remove the ground pin under any
circumstances!
This machine is intended for
Commercial use. It is constructed for use in an
indoor environment and is not intended for any
other use. Use only recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:
1] Do not operate machine:
- Unless trained and authorized.
- Unless you have read and understand
operators manual.
- In flammable or explosive areas.
- With a damaged cord or plug.
- If not in proper operating condition.
- In outdoor areas.
- In standing water.
- Without bag/filters in place
- With the use of extension cords.
2] Before operating machine:
- Make sure all safety devices are
in place and operate properly.
3] When using machine:
- Do not run machine over cord.
- Do not pull machine by cord
or plug.
- Do not pull cord around sharp
edges or corners.
- Do not unplug by pulling on the
cord.
- Do not stretch cord.
- Do not handle plug with wet
hands.
- Keep cord away from heated
surfaces.
- Do not pick up burning or smoking
debris such as cigarettes,
matches or hot ashes.
- Report machine damage of faulty
operation immediately.
4] Before leaving or servicing machine:
- Turn off machine.
- Unplug cord from outlet.
5] When servicing machine:
- Unplug cord from outlet.
- Use manufacturer supplied or
approved replacements parts.
To avoid electrical shock, please
replace the power cord immediately
if any damage is being detected,
The replacement must be performed
only by an authorized person or by
our customer service centor.
Page 4
Operation of the Canister Vacuum
* Read operators manual thoroughly
prior to operating or servicing this
machine.
DRY PICKUP
1] Remove The vac head of machine and
confirm that there is either a cloth of
paper filter in place.
2] Replace & the latch vac head.
* Be sure the machine is not plugged
into an outlet.
3] Connect vacuum hose to inlet on the
machine body.
4] Remove tool storage lid on top of
machine and unwind power cord..
5] Choose appropriate tool, and attach it
to the free end of the hose .
6] Plug power cord into grounded
outlet.
* Do not use an extension cord in
conjunction with the standard power
cord.
7] To start the machine, push on the
red power button located above the
left rear wheel.
8] Check the filter bag periodically to see
if it is full. For optimal performance,
replace the bag when it is 3/4 full.
9] This machine is designed to be pulled
around by the vacuum hose, so pull the
hose, and the vacuum will follow.
10] To stop the machine at any time,
simply press the red power switch &
the machine will stop automatically.
MAINTENANCE
To keep the machine performing well for
many years, please follow the following
maintenance procedures.
* Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1] Unplug machine as soon as you are
done using it.
2] Rewind the power cord into the tool
storage area..
3] Replace the tool into the tool storage
area.
4] Check power cord for any damage. If
any damage is detected, replace the
cord immediately.
5] Lubricate wheels & casters with a
water resistant lubricant every month.
6] Check machine for loose or missing
nuts and bolts, and replace as
necessary.
7] Check the motor cover / filter, and
clean it after each use.
8] Remove the vacuum hose and check it
for any holes and clogs.
9] Clean the outside of the machine with
a mild cleaner.
STORAGE
1] Unplug machine from power source.
2] Properly store power cord and tools in
the on-board storage compartment.
3] Store in upright position in a dry area.
Page 5
PARTS LIST
Page 6
DIA
NO
PART
NUMBER
DESCRIPTION
NO
REQ'D
1VF47035ALOGO1
2VA41012ATOP COVER1
3VA41048BUTTON1
4VA41045LATCH1
5VA41047SPRING1
6VA14216PIN Ø3X301
7VA41044HOUSING,LATCH1
8VA13469SELF-TAPPING SCREW,ST3X124
9VA13487SELF-TAPPING SCREW,ST3X124
10VA41043SHIELD1
11VA41046BLOCK,LATCH1
12VA14007PIN Ø4X122
13VA41010ABASE,TOP COVER1
14VA41021SPRING2
15VA41009PUSH BUTTON1
16VA41008COVER,UPPER HANDLE1
17VA14487SELF-TAPPING,SCREW,ST3X166
18VA41011GASKET,BASE,TOP COVER2
19VA41013FOAM FILTER,TOP COVER1
20VA41026FILTER,TOP COVER1
21VA41006AFILTER HOLDER1
22GT13001SELF-TAPPING,SCREW,ST5X126
23VA13492SCREW,M5X126
24VA41041HOLDER1
25VA41029INTAKE1
26VA14006ASCREW,M3X68
27VA41007COVER,LOWER HANDLE1
28VA41004-3STRIKE,PUSH BUTTOM1
29VA41004LOWER HANDLE1
30VA41005TANK1
31VV20509SCREW M5X103
32VV13662WASHER,PLAIN Ø5XØ12X12
33VA65002CORD1
34VA41034GASKET,BASE,TOP COVER1
35VA41019GROMMET1
36VA13488AWASHER,LOCK2
37VA41042SEAL1
38VF14004LOCK2
39VA41014AXEL1
40VA13474SCREW,M5X168
PARTS LIST
Page 7
DIA
NO
PART
NUMBER
DESCRIPTION
NO
REQ'D
PARTS LIST
41VA41003ATANK SEAT1
42VA41036VAC MOTOR, 110V1
43VA41032GASKET1
44VA41015AMOTOR SEAT1
45GT13004SELF-TAPPING,ST5X168
46VA41031FOAM FILTER,MOTOR1
47VA21544ASERIAL TAG1
48VF40994READ MANUAL1
49VF47027WASHER,LOCK2
50VF47055REAR WHEEL2
51VA96851CAP,AXEL2
52VA41017PUSH SWITCH BUTTON1
53VA20209-16SPRING,SWITCH BUTTON1
54VA41018ASEAT,SWITCH1
55VA41024ASWITCH(HP12AS2HOOO)1
56VA41030ABRACKET,SWITCH1
57VV13640SELF-TAPPING SCREW ST4X162
58VA21517CLAMP BLOCK,CABLE1
59VA13470SELF-TAPPING,ST3X162
60VA41016FOAM FILTER,STRIP1
61VA41001BOTTOM COVER1
62VA41002BUMPER1
63VA91345CASTER1
64GT13002SELF-TAPPING,ST5X246
Page 8
ACCESSORIES
Page 9
DIA
NO
PART
NUMBER
DESCRIPTION
NO
REQ'D
1VA41130HOSE ASSY1
2VA41023PAPER BAG1
3VA20205TUBE2
4VA41027VACUUM BAG,CLOTCH1
5GT0012BCOMBINATION TOOL1
6VA20804DUSTING TOOL1
7VA20805CREVICE TOOL1
8VA20802-1UPHOLSTERY TOOL1
PARTS LIST
Page 10
Motor
Cord
Supply
Power
SJTW 16/3C
Supply
Cord
Power
MB39CV
Wiring Diagram
120V
SINGLE
SUPPLY
PHASE
60HZ
SWITCH
BLACK
WHITE
G/Y
BLACK
G/Y
BLACK
Loading...