Viper DR1500H Owner's Manual

VF41529

REV.05(12-08)

VIPER ...exceptional

value

www.usviper.com

VIPER NORTH AMERICA

[phone]

P.O. BOX 104

HAMILTON, MI 49419

(866) 41 - VIPER

IMPORTANT: READ OWNERS MANUAL CAREFULLY

DRAGON SERIES

SERIAL#

MODEL#

DR1500H

Please fill out & return your warranty card!

OWNERS MANUAL

VIPER

HIGH SPEEDS

https://harrissupplyind.com - To Order Parts Call 608-268-8080

CONGRATULATIONS on your purchase of a Viper
product, and welcome to the V.I.P. family. We
appreciate your business and will do everything in our
power to keep you happy with your purchase for many
years to come.

As part of the V.I.P. family, you are entitled to the best
protection by one of the most comprehensive warranties
in
the industry.

Thank-you for purchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS

Safety Precautions 3
Machine Operation 4
Machine Maintenance & Storage 4
Parts Lists 5-10
Wiring Diagram 11

https://harrissupplyind.com - To Order Parts Call 608-268-8080

https://harrissupplyind.com - To Order Parts Call 608-268-8080

SAFETY PRECAUTIONS

!!! This machine must be grounded!
Grounding provides the path of least
resistance for electrical current. To
reduce the risk of electrical shock
should the machine malfunction, the
machine has a special grounding plug.
Do not remove the ground pin under
any circumstances!

This machine is intended for commercial
use. It is constructed for use in an
indoor environment and is not intended
for any other use. Use only
recommended accessories.

All operators shall read, understand
and exercise the following safety
precautions:

1) Do not operate machine:

- Unless trained and authorized

- Unless you have read and
understand operators manual

- In flammable or explosive areas.

- With damaged cord or plug.

- If not in proper operating condition.

- In outdoor areas.

- In standing water.

- With the use of extension cords.

2) Before operating machine:

- Make sure all safety devices are
in place and operate properly.

3) When using machine:

- Do not run machine over cord.

- Do not pull machine by cord or
plug.

- Do not pull cord around sharp
edges or corners.

- Turn power switch to “off “ prior
to unplugging machine.

- Do not unplug by pulling on the
cord.

- Do not stretch cord.

- Do not handle plug with wet
hands.

- Keep cord away from heated
surfaces.

- Do not pick up burning or
smoking debris such as
cigarettes, matches or hot
ashes.

- Report machine damage or
faulty operation immediately.

4) Before leaving or servicing machine:

- Turn off machine.

- Unplug cord from outlet.

5) When servicing machine:

- Unplug cord from outlet.

- Use manufacturer supplied or
approved replacement parts.

3

Operation of High Speed Floor Machine

* Read operators manual thoroughly prior

to operating or servicing this machine.

GENERAL USE

1] Remove any obstructions or other

obstacles in the area which is to be
cleaned.

2] Place handle in upright position and tilt

machine back until handle rests on the
floor.

* Be sure the machine is not plugged into
an outlet.

3] Remove the pad center gripping device

by unscrewing the thumbscrews.

4] Place appropriate burnishing pad on

pad driver and re-attach the center
gripping device.

5] Place machine back into its upright

position.

6] Plug power cord into grounded outlet.

* Do not use an extension cord in
conjunction with the standard power cord.

7] Adjust the handle height to a

comfortable operating position.

8] To start the machine, push on the Red

safety button on the top of the upper
switch housing, and then squeeze either
of the switch levers.

9] When the machine is in operation, both

hands should be placed on the handle
(switch housing).

10] To stop the machine at any time,

simply release the switch lever, and the
machine will stop automatically.

MAINTENANCE

To keep the machine performing well for

many years, please follow the following

maintenance procedures.

* Always confirm that the machine is

unplugged prior to performing any

maintenance or repairs.

1] Unplug machine as soon as you are not

using it.

2] Clean the outside of the machine with a

mild cleaner.

3] Check power cord for any damage. If any

damage is detected, replace the cord
immediately.

4] Lubricate wheels with a water resistant

lubricant every month.

5] Check machine for loose or missing nuts

and bolts, and replace as necessary.

6] If the machine is used in a dusty

environment, you may remove the

motor cover and blow the motor clean

with compressed air. This will allow for
good ventilation and help the motor run

cooler.

STORAGE

1] Unplug machine from power source.

2] Store in upright position in a dry area.

4

https://harrissupplyind.com - To Order Parts Call 608-268-8080