Viper BARRACUDA CUDA26 Owner's Manual

VA51063

REV.02(08-07)

VIPER ...exceptional

value

www.usviper.com

VIPER NORTH AMERICA

[phone]

P.O. BOX 104

HAMILTON, MI 49419

(866) 41 - VIPER

IMPORTANT: READ OWNERS MANUAL CAREFULLY

BARRACUDA

SERIAL#

MODEL#

CUDA26

Please fill out & return your warranty card!

OWNERS MANUAL

DUAL MOTOR VACUUM

CONGRATULATIONS on your purchase of a Viper product,
and welcome to the V.I.P. family. We appreciate your
business and will do everything in our power to keep you
happy with your purchase for many years to come.

As part of the V.I.P. family, you are entitled to the best
protection by one of the most comprehensive warranties in
the industry.

Thank-you for purchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS

Safety Precautions 1

Machine Components 2

Machine Operation 3-4

Machine Maintenance & Storage 4

Troubleshooting 5

Parts Breakdown 6

Parts Lists 7-8

Accessories 9

Wiring Diagram 10

SAFETY PRECAUTIONS

GROUNDING INSTRUCTIONS
General – This carpet vacuum shall be
grounded while in use to protect the
operator from electric shock. The
machine is provided with a three-contact
grounding type attachment plug to fit the
proper grounding type receptacle. The
green (or green & yellow) conductor in
the cord is the grounding wire. Never
connect this wire to other than the
grounding pin of the attachment plug.

This machine is for use on a nominal
120-volt circuit and has a grounding plug
that resembles the plug illustrated in
figure below. Make sure that the
machine is connected to an outlet having
the same configuration as the plug. No
adapter should be used with this machine.

This machine is intended for commercial
use. It is constructed for use in an indoor
environment and is not intended for any
other use. Use only recommended
accessories.

All operators shall read, understand and
exercise the following safety precautions:

1) Do not operate machine:

- Unless trained and authorized

- Unless you have read and
understand operators manual

- In flammable or explosive areas.

- With damaged or modified cord or
plug.

- If not in proper operating condition.

- In outdoor areas.

- In standing water.

- Without bag / filters in place.

- With the use of unapproved
extension cords.

2) Before operating machine:

- Make sure all safety devices are in
place and operate properly.

3) When using machine:

- Do not run machine over cord.

- Do not pull machine by cord or
plug.

- Do not pull cord around sharp
edges or corners.

- Do not unplug by pulling on the
cord.

- Do not stretch cord.

- Do not handle plug with wet hands.

- Keep cord away from heated
surfaces.

- Do not pick up flammable
materials or reactive metals.

- Report machine damage or faulty
operation immediately.

- Do not allow children to operate
machine.

4) Before leaving or servicing machine:

- Turn off machine.

- Unplug power cord from outlet.

5) When servicing machine:

- Unplug cord from outlet.

- Use manufacturer supplied or
approved replacement parts.

- Avoid moving parts. Do not wear
loose clothing.

1

1) Handle

2) Power cord

3) Door latch

4) Power switch

5) Attachment tool intake & cord wrap

6) Vacuum hose

7) Brush housing

8) Brush height adjustment

9) Rear wheels

10) Exhaust vent

11) Handle height adjustment

12) Brush circuit breaker (bottom side)

13) Brush assembly (bottom side)

14) Rear door

MACHINE COMPONENTS

1

2 3

4 5 6

7 8

9

10

11 14

12 13

2

MACHINE OPERATION

PRIOR TO VACUUMING CARPETS

1) Inspect power cable and extension

cable for damage. Replace cable if
damage is found.

2) Ensure filter bag is properly installed

NOTE: Never operate machine
without filter bag installed. This
could cause damage to the vacuum
motor.

3) Set proper height adjustment for

carpet being cleaned.

CARPET VACUUMING

1) Depress foot pedal and lower vacuum

head to floor.

2) Turn on power switch.

3) Operate by using standard vacuuming

procedures.

4) Check bag periodically to see if it is

full. Replace if necessary.

5) To clean under desks or other tight

areas, depress the foot pedal an
additional time to lower the handle
even further.

OPERATING HINTS

1) Overlap cleaning path by approx. 2

inches

2) Work away from power outlet and

power cable in order to avoid damage
to the power cable.

3) Occasionally check the bag for

fullness & replace as necessary.

4) If brush stops spinning, there may be

an obstruction in the brush. Unplug
the power cable, raise the brush off
the floor and check for an obstruction.
Check & reset the brush circuit
breaker located on the bottom of the
brush housing.

USE OF ACCESSORY TOOLS

NOTE: Accessory tools are available as
an option. Kit VA51061 includes:
Dusting brush, crevice tool, upholstery
tool, 8’ vacuum hose, etc.

1) Machine must be in upright position

whenever using attachment tools.

2) Remove vacuum hose on the vacuum

intake port on rear of machine.

3) Connect (optional) 8’vacuum hoses

to intake port & connect desired
accessory tool to end of hose.

4) Turn on vacuum switch and operate

tool using normal vacuuming
procedures.

3

VACUUM BAG INSTALLATION &

REMOVAL

1) Unlock rear door latch, and allow

door to hinge open.

2) Place paper bag / filter into tank

opening.

3) On paper bag / filter, slide rubber

vacuum collar onto vacuum intake
spout.

4) Close rear door and lock into place.

NOTE: Be sure the bag / filter is

properly placed in bag housing to
ensure proper air flow.

5) To remove bag, simply reverse steps

1-4 above.

6) Do not re-use paper bag / filter.

When full, dispose of it and replace
with a new one.

MACHINE MAINTENANCE

To keep the machine performing well
for many years, please follow the
following maintenance procedures.

!!! Always confirm that the
machine is unplugged prior to
performing any maintenance or
repairs!!!

1) Unplug machine as soon as you are

done using it.

NOTE: When unplugging machine, do
not pull cord around sharp edges or
corners & do not unplug by pulling on
the cord.

2) Clean outside of machine with a mild

cleaner.

3) Check power cord for any damage. If

any damage is detected, replace the
cord immediately.

4) Check machine for any loose or

missing nuts and bolts and replace as
necessary.

5) Check paper bag / filter for fullness.

If it is full, replace with a new one.

6) Check vacuum motor filter and

exhaust filter for debris and clean as
needed.

NOTE: Do not clean filters with water

or a cleaning solution. Clean by tapping
of debris or blowing with air.

7) Inspect brush for strands of carpet

and debris and remove as needed.

8) Inspect brush bristles for wear and

damage. Replace brush as needed.

9) Inspect gaskets and seals for air leaks

and replace as needed.

10) Check vacuum hose for clogs and

holes and replace as needed.

11) Check vacuum motor carbon brushes

every 250 hours. Replace brushes
when they are 3/8” or less in length.

NOTE: Vacuum motor damage
caused by worn brushes is not
covered by warranty.

MACHINE STORAGE

1) Prior to storing the machine, wrap up

power cord, check paper bag / filter
for fullness and replace if necessary.

2) Clean and / or replace filters.

3) Store machine in upright position in a

dry area, with the brush head off the
floor.

4

PROBLEM CAUSE SOLUTION

Machine does not work Power switch not in "on" position Turn power switch "on"

Power cord not plugged into outlet Plug power cord into outlet

Power cord is faulty Replace with approved power cord

Building circuit breaker tripped Reset circuit breaker

Faulty wiring Contact Viper Distributor

Faulty on / off switch Contact Viper Distributor

Brush does not work Brush circuit breaker tripped

Check brush and belt for obstructions and

remove as needed

Reset circuit breaker

Poor brush pickup Incorrect brush height adjustment Adjust brush height

Clogged brush Remove debris from brush

Brush is worn Contact Viper Distributor

Loose brush drive belt Inspect belt and replace as needed

Low suction Vacuum hose clogged

Remove vacuum hose and check for

obstructions

Vacuum hose faulty

Check vacuum hose for loose cuffs or holes

and replace as needed

Filters clogged

Remove vacuum filter and exhaust filter and

clean

Vacuum bag full

Check vacuum bag / filter and relplace as

needed

BASIC TROUBLESHOOTING

5

PARTS LIST

6

DIANOPART

NUMBER

DESCRIPTION

NO

REQ'D

1 VA51009 HANDLE HOUSING 1

VA51025 PAPER BAG, DUST, 10.5qt. 1

VA51067 CLOTH BAG, DUST(OPTIONAL)
3 VA51007 REAR COVER AND BAG HOLDER 1
4 GT13022 NUT, M5, NYLON INSERT 5
5 VA51034 GASKET, ADAPTER 1
6 VA51008 ELBOW ADAPTER, HOSE 1
7 VA51022 PLUG AND CORD HOOK 1
8 VV20501 SCREW, M5x14 20
9 VA13489 NUT, ACORN, M6 1

10 VA51023 HOSE, 2" 1
11 VF13533

WASHER, PLAIN, φ6

10
12 VV13635 SCREW, M5x20 3
13 VF82028 WIRE ROPE, STAY, REAR COVER 1
14 VF13495 SCREW, HEX, M6x16 5
15 VF13502 NUT, M6, NYLON INSERT 1
16 VA51065 FILTER, EXHAUST 1
17 VA51064 HOUSING, EXHAUST FILTER 1
18 VA51050 GASKET, HANDLE HOUSING, 8x13mm, SBR 1
19 VA51073 LATCH PLATE 1
20 VV13605 SCREW, FLAT, M6x16 2
21 VA51041 NYLON WASHER 4
22 VA51027 AXLE 1
23 VA51059 ECCENTRIC BUSHING 2
24 VV20509 SCREW, M5x10 17
25 VF13520

RETAINING RING, EXTERNAL, φ12

2

26 VF13538

WASHER, PLAIN, φ12xφ24x2

2
27 VF48202 WHEEL, 5" 2
28 VF13666

WASHER, PLAIN, φ12

2
29 VF44012 SCREW, M5x12.7 2
30 VA51038 SPRING, LATCH 1
31 VF14214 SCREW, M5x8 1
32 VA51039 SHOULDER BOLT, LATCH 1
33 VV67504 CIRCUIT BREAKER, 2AMP 1
34 GT13057 SCREW, SELF-TAPPING, ST5x10 14
35 VA51002 BUMPER, 26" 1
36 VF99926-1 RECTIFIER 1
37 VA51066 BLOCK, BRUSH SHAFT, LEFT 1
38 ZD57000 MOTOR, BRUSH, 115V 1
39 VA51011 MOUNT PLATE, MOTOR 1
40 VA51019 PULLEY, MOTOR 1

2

PARTS LIST

7

DIANOPART

NUMBER

DESCRIPTION

NO

REQ'D

41 VA51021 DRIVE BELT 1
42 VF14254 SCREW, HOLDING, M5x8 1
43 VA51018 PULLEY, BRUSH 1
44 VA51035 KNOB, ROLLER ADJUST 1
45 VF13508 SCREW, HOLDING, M4x8 1
46 VA51037 SPRING, ROLLER ADJUST 1
47 VA51036 LOCK PIN, ROLLER ADJUST 1
48 VA51042 ROLLER, 1.5" 2
49 VA51013 CLAMP, ROLLER BRACKET 4
50 VA51043 AXLE, ROLLER 2
51 VA14001

RETAINING RING, EXTERNAL, φ10

4
52 VA51014 ROLLER BRACKET 1
53 VA51004 BOTTOM SHOE PLATE, 26" 1
54 VA51005 BRUSH, 26" 1
55 VA51005A BRUSH, ASSEMBLY, 26" 1
56 VA51047 BRACKET, RECTIFIER 1
57 VA51003 BRUSH HOUSING, 26" 1
58 VA51006 SHAFT, BRUSH, 26" 1
59 VA51015 BEARING 2
60 VA51017 STRING GUARD, BRUSH 1
61 VA51016 BLOCK, BRUSH SHAFT, RIGHT 1
62 VV20502 SCREW, FLAT, M5x16 2
63 VA51048 LABEL, "BARRACUDA" 1
64 VA51001 BASE HOUSING, 26" 1
65 VA51071 LATCH, HANDLE 1
66 VA13476 SCREW, M5x40 1
67 VA51040 SHOULDER BOLT, PIVOT 2
68 VA51052 LABEL 1
69 VA51012 TUBE, BASE HOUSING 1
70 VV10120 CLAMP 1
71 GT13070 SCREW, SELF-TAPPING, ST4.8x25 4
72 VA51032 RETAINER RING, VACUUM MOTOR 1
73 VA51033 GASKET, VACUUM MOTOR 1
74 ZD52000A VACUUM MOTOR, 115V 1
75 VA51049 FILTER, VACUUM MOTOR 1
76 VF82082 LOGO, "VIPER" 1
77 VA65001 POWER CORD, 14/3C, SJTW, 50FT 1
78 VA51044 STRAIN RELIEF, CORD 1
79 VF83109 CATCH 1
80 VV13650 SCREW, M4x10 6
81 VA51026 PLATE, SWITCH 1
82 VF91346 SWITCH, ROCKER 1

PARTS LIST

8

ACCESSORIES

DIA

NO

PART

NUMBER

DESCRIPTION

NO

REQ'D

1 VA51061 KIT TOOLS (OPTIONAL) 1
2 VA51060 HOSE ASSY 1
3 VA20803 DUSTING TOOL 1
4 VA20806 CREVICE TOOL 1
5 VA20807 UPHOLSTERY TOOL 1
6 VA20209 WAND 1
7 VA20248 TUBE 2

ACCESSORIES PARTS LIST(OPTIONAL)

9

Green

BlackBlack

White

Green

White

Green

Black

BlackWhiteWhite

Yellow/Green

Black Black

Motor

Wiring Diagram

CUDA26

SJTW 14/3C

Cord

Supply

Power

Switch

Vacuum

White White

Green

Circuit

Breaker

Green

Motor

Brush

RedBlack

White

Black

~

~

+

Rectifier

10