Congratulations on the purchase of your state-of-the-art vehicle secu ri ty system. This system has been designed to provide years
of trouble-free op er a tion. Due to the complexity of this system, it
must be installed by an authorized dealer only. Installation of this
product by anyone other than an authorized dealer voids the warranty. All dealers are provided with preprinted dealer cer tifi cates
to verify that they are au tho rized.
This owner’s guide should help you to get the most out of your
system. Please take the time to read it prior to using the system.
➢ System maintenance
The system requires no specific maintenance. Your remote control
is pow ered by 2 small, lightweight CR2016 batteries. When the
batteries weakens, operating range will be reduced and the LED
on the remote will dim.
Your warranty registration must be returned and the bar code serial number must not be removed. If the warranty registration is
not returned, you do not have a warranty. It is also necessary to
keep your proof of purchase, which reflects that the product was
installed by an au tho rized dealer. Make sure that you receive the
warranty registration from your dealer.
➢ FCC/ID notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two con di tions: (1) This device may not
cause harmful interference, and (2) This device must accept any
in ter fer ence re ceived, including in ter fer ence that may cause undesired op er a tion.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this device.
The system uses a computer-based learn routine to learn the transmit ter buttons. This makes it possible to assign any transmitter button
to any system function. The transmitter initially comes programmed
with Standard Configuration, but may also be customized by an
authorized dealer. The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter.
➢ Standard configuration
Button
The arming function is controlled by pressing this button for one
second.
Button
The disarming function is controlled by pressing this button for
one second.
Button
Silent Mode™ and an optional auxiliary function are controlled
by pressing this button. (Silent Mode works by pressing this button
for less than one second before arming or disarming. An optional
auxiliary function, such as trunk release, can be controlled by
pressing this button for 1.5 seconds.)
The auxiliary output controls __________________________.
Button
The panic feature is controlled by pressing this button for two
seconds.
and
Buttons
An optional auxiliary convenience or expansion function that you
have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls_________________________.
➢Three-button configuration
(Available with optional three-button transmitter.)
Button
The arming and disarming functions are controlled by pressing
this button for one second.
Button
Silent Mode™ and an optional auxiliary function are controlled
by pressing this button. (Silent Mode works by pressing this button
for less than one second before arming or disarming. An optional
auxiliary function, such as trunk release, can be controlled by
pressing this button for 1.5 seconds.)
The auxiliary output controls __________________________.
Button
The panic feature is controlled by pressing this button for two
seconds.
The buttons used in the instructions in this manual correspond to
the standard con fig u ra tion. Remember, this is not the only way
your trans mit ter may be set up. It can be custom configured to
meet your needs.
➢ Active arming
You can activate, or arm, the system by pressing
transmitter for one second. When the system arms, you will hear
a short siren sound, or chirp, and the parking lights will flash
once. If the vehicle’s power door locks have been connected to
the system, the doors will lock.
While the system is armed, the status LED will flash approximately
once per second, indicating that the system is actively protecting
your vehicle. If you hear a second chirp after arming, and see the
status LED flashing in groups, refer to the Diagnostics section of this
guide. This extra chirp is called Bypass No ti fi ca tion.
➢ Passive arming
The system also can be programmed to arm itself automatically
(called passive arming). If the system is programmed for passive
arming, it will automatically arm 30 seconds after the ignition is
turned off and the system “sees” you leave the vehicle by opening and closing a door. Whenever the system is in its 30-second
passive-arming countdown, the status LED will flash twice as fast
as it does when the system is armed. The siren will chirp one time
20 seconds after the last door has been closed. The system is
not actually armed at that point. The system arms and the doors
lock (if connected and programmed for passive locking) at the 30
second mark, but the siren will not chirp. The early chirp provides
you with a 10-second warning prior to arming.
If any protected entry point (such as a door or a switch-protected
trunk or hood) is open, the system will not passively arm (unless
forced passive arming is programmed on). See Pro gram ming Options section of this guide. Additionally, each time a protected
entry is triggered during the arming countdown, the 30-second
countdown starts over.
When armed, your vehicle is protected as follows:
Light impacts will trigger the Warn Away
®
signal. When triggered, the siren will chirp and the parking lights will flash for a
few seconds.
Heavy impacts will trigger the system. The triggered sequence is
between 1-180 seconds of constant siren and flashing parking
lights.
If a door is opened, the system will immediately start chirping the
siren and flashing the parking lights. Three seconds later, the siren
output changes to a con tin u ous blast. This pro gres sive re sponse
gives you time to dis arm the sys tem with your transmitter if you
inadvertently open the door while the sys tem is armed, while still
providing an instant response (even if the door is im me di ate ly
closed).
Turning on the ignition key will trip the same two-stage response
as opening a door.
The optional starter kill prevents the vehicle’s starter from cranking.
The Multi-Level Security Arming feature is available with the fourbutton transmitter only.
Multi-Level Security Arming allows you to select which of the security system’s inputs or sensors are to be active and which are to
be bypassed, when arming the system. (See the Table of Zones
section of this guide.)
Pressing
again within five seconds of arming the security
system will activate the Multi-Level Security Arming feature.
Each time
is pressed again, a different security level is se-
lected. The different security levels can be selected as follows:
Press •
once: The siren chirps once. The system is
armed.
Press •
twice within five seconds: The siren chirps twice
followed by a long chirp. Zone 2 is now bypassed.
Press •
three times, within five seconds the siren chirps
three times followed by a long chirp. Zone 4 is now bypassed.
Press •
a fourth time within five seconds: The siren chirps
four times followed by a long chirp. Zones 2 and 4 are now
bypassed.
Press •
a fifth time within five seconds: The siren chirps five
times followed by a long chirp. All input zones, except the