VIP INTIPRKIT Quick Installation Manual

MODEL: INTIPRKIT

Residential IP Intercom Kit

Includes Door station and Indoor Monitor

‘QUICK INSTALLATION GUIDE’

Indoor Monitor

Door Station

- Advanced H.264 Video Compression Technology

- Advanced H.264 Video Compression Technology

- Easy to operate touch screen

- High Quality 1.3MP CMOS Image sensor

- 10/100Mbps Ethernet

- 10/100Mbps Ethernet

- Info publish, leave message, emergency calling

- Unlock Door Remotely

- 4Gb Internal Storage

- Built-in loudspeaker

- 12v DC

- 12v DC

N517

www.rhinoco.com.au

V2.0 040314

2

3

Package Contents (Before installation, please ensure you have all the parts listed below).

1 x Indoor Monitor INTIPMONB

● Advanced H.264 Video Compression Technology for High Quality Images

● Easy to Operate

● Touch Screen

● 4Gb Internal Storage (non-removable SD Card)

● 12v DC

1 x Door Station INTIPRDSV

● 1.3MP HD Image

● Easy to Operate

● Loudspeaker

● Door Release Output

● 12v DC

1 x 86 Box for Door Station

● Assist with mounting the INTIPRDSV Door Station to concrete or brick
environments

1 x Cat5e Ethernet Cable

● Pre-terminated - Allowing Simple Plug-in Connection

● 30m Ethernet Cable

2 x Switch Mode Power Supplies

● 2 x 12v DC Power Supplies for use with the Monitor and Door Station

4

Installation of an Indoor monitor

1. Use screw b to fix bracket ② onto box ④.

2. Use screw a to fix bracket ② onto wall ③.

3. Connect network cable and 12vDC power

4. Face rear installation slot to slot on bracket. Make it against wall and push lightly downward until it
fits in to slot on bracket.

5. Remove: Insert small screwdriver into hole on device ①, and push device upward until removed.

Screw Illustration

No.

Name

Illustration

Quantity

a

ST3×18 Cross recessed pan head tapping screws - white alloy

3

b

M4×30 Cross recessed pan head screws

2

c

Expansion pipe ￠6*30mm white

3

5

Installation of a Door Station

1. Mount 86 box in to wall cavity.

2. Connect network cable and 12vDC power

3. Fix Door Station onto wall:

a. Use the included M4 screws to attach Door Station onto the 86 box.
b. In order to secure the Door Station, use the ST3.0 screw included with Door Station to

affix the Door Station onto wall after attachment to the 86 box. (as b Above).

4. Attach cover ① onto Door Station ②, using screws a to affix.

Screw Note

No.

Name

Illustration

a

M3×8 Cross recessed countersunk head-black zinc

b

M4×30 Cross recessed pan head screws

c

ST3×18 Cross recessed pan head tapping screws –white alloy

d

Expansion pipe ￠6*30mm white

6

Intercom System Configuration

The process to set up your Intercom system may vary depending upon your system structure. Please
see the following examples of system structures and follow the process which best meets your
requirements.

System Structure A – Standalone 1 to 1 by direct connection

This configuration has only 1 of each unit and requires a single Cat5e network cable to run directly from
the Indoor Monitor to the Door Station.

System Structure B – Standalone 1 to 1 system via a network switch

This configuration has only 1 of each unit and requires a Cat5e network cable from each Indoor Monitor
and Door Station, to the network switch.

System Structure C – Standalone 1 to 1 system via an existing computer network

This configuration still has only 1 of each unit but has a Cat5e network cable from both the Indoor
Monitor and Door Station, to your network switches and then uses the existing LAN to connect. Even
through the Intercom system will be running across your network, it will still use its Default IP address
range.

System Structure D – Multiple Door Stations to a Monitor via a network

This configuration is more complex as you can use 2 or more Door Stations with an Indoor Monitor but
you will need to change some IP addresses. You will require a Cat5e network cable from each the Indoor
Monitor and Door Station, to a network switch or to your existing LAN.

System Structure E – Single Door Stations to Multiple Monitors via a network

This configuration is more complex as you can use your Door Stations with 2 or more Indoor Monitors
but you will need to change some IP addresses. You will require a Cat5e network cable from each the
Indoor Monitor and Door Station, to a network switch or existing LAN to connect.

System Structure F – Multiple Door Stations to Multiple Monitors via a network
This configuration is the most complex as you will need to change the IP address of each Door Station
and each Indoor Monitor. It will allow you to use up to 6 Indoor Monitors and 6 Door Stations together.
You will also require a Cat5e network cable from each the Indoor Monitor and Door Station, to a network
switch or to your existing LAN.

The User Password is 123456 which may be used for basic operation of the Intercom System.
The Project Password 002236 is required only for configuration and set up of additional devices.
The Door stations own web interface of will require the Username admin and a Password of admin.

7

System Structure A – Standalone 1 to 1 by direct connection

This configuration requires only a single Cat5e network cable to run directly from the Indoor Monitor to
the Door Station.

- Very Simple System Structure

- Plug and Play, no set up required.

- Uses a default IP Address range.

- Each Indoor Monitor and Door Station will require their own 12vDC power supply.

1. Install each unit at their respective location and connect to the shared Cat5e network cable.

2. Power on the Door Station

3. Power on the Indoor Monitor

4. You have now successfully set up your VIPvision Intercom System.

8

System Structure B – Standalone 1 to 1 system via a network switch

This configuration requires a Cat5e network cable from each Indoor Monitor and Door Station, to the
network switch.

- Simple System Structure

- Plug and Play, no set up required.

- Uses a default IP Address range.

- Each Indoor Monitor and Door Station will require their own 12vDC power supply.

- Network switch required.

1. Install each unit at their respective location and connect to their Cat5e network cable.

2. Connect each Cat5e network cable to the network switch.

3. Power on the network Switch

4. Power on the Door Station

5. Power on the Indoor Monitor

6. You have now successfully set up your VIPvision Intercom System.

9

System Structure C – Standalone 1 to 1 system via an existing computer network

This configuration is very similar to B as it requires a Cat5e network cable from both the Indoor Monitor
and Door Station, to your network switches and then uses the existing LAN to connect. Even through the
Intercom system will be running across your network, it will still use its own IP addresses of 10.22.5.180
(Indoor Monitor) and 10.22.5.189 (Door Station).

You have the option of using the default IP address range 10.22.5.x (and not changing anything) or using
your own LAN IP address range (and changing the IP Address of each units). So in this example we will
be using the default IP address range 10.22.5.x and leaving it as is.

- Advanced System Structure

- Plug and Play, no set up required.

- Uses a default IP Address range.

- Each Indoor Monitor and Door Station will require their own 12vDC power supply.

- Network switch required.

1. Install each unit at their respective location and connect to their Cat5e network cable.

2. Connect each Cat5e network cable to the network switch.

3. Power on the Door Station

4. Power on the Indoor Monitor

5. You have now successfully set up your VIPvision Intercom System.