Vintage Cellars WS-9066U-IT-CBP User Manual

1

LCD

Display

Function keys

2

Stand

Function keys

Battery
compartment

Hanging
hole

3

Remote transmission of outdoor

4

WS-9066U-IT

WEATHER STATION

INTRODUCTION:

Congratulations on purchasing this state-of-the­art weather station as an example of innovative
design and quality piece of engineering.
Provides time, calendar, weather forecast, moon
phase, indoor and outdoor temperature, indoor
and outdoor relative humidity. This unit will
never keep you guessing on current and future
weather conditions. Operation of this product is
simple and straightforward. By reading this
operating manual, the user will receive a better
understanding of the Weather Station.

FEATURES:

The Weather Station

Instruction Manual

x 12/24 hour time display
x Calendar display (year only in setting

mode)

x Display 8 Moon phases throughout the

year

x Temperature display in ºC/ ºF
x Indoor and outdoor temperature display

with MIN/MAX records

x Indoor and outdoor humidity display
x Humidity data display as RH%
x Low battery indicator
x Table standing or wall mounting

Thermo-Hygro Transmitter

temperature and humidity to
weather station by 915MHz

x Wall mount bracket
x Mounting at a sheltered place.
x Avoid direct rain and sunshine

DO NOT MIX OLD AND NEW BATTERIES.

DO NOT MIX ALKALINE, STANDARD, OR
RECHARGEABLE BATTERIES

TO INSTALL AND REPLACE BATTERIES
IN THE THERMO-HYGRO TRANSMITTER

The outdoor thermo-hygro transmitter uses 2 x
AAA, IEC LR3, 1.5V batteries. To install and
replace the batteries, please follow the steps
below:

to be reset by following the setting up
procedures. This is due to a random security

1. Remove the battery cover.

2. Insert the batteries,
observing the correct polarity (see
battery compartment marking).

3. Replace the battery cover

on the unit.

Note:

In the event of changing batteries
in any of the units, all units need

code assigned by the transmitter at start-up.
This code must be received and stored by the
weather station in the first 3 minutes of power
being supplied to the transmitter.

TO INSTALL AND REPLACE BATTERIES
IN THE WEATHER STATION

The weather station uses 2 x AAA, IEC LR3,

1.5V batteries. To install and replace the
batteries, please follow the steps below:

3. Replace compartment cover.

BATTERY CHANGE:

It is recommended to replace the batteries in all
units on an annual basis to ensure optimum
accuracy of these units.

Please participate in the
preservation of the environment.
Return used batteries to an
authorized depot.

1. Insert finger or
other solid object in
the space at the
bottom center of the
battery compartment
and lift up to remove
the cover.

2. Insert batteries

observing the correct
polarity (see marks).

5

6

+ key

MIN/MAX

key

SET key

7

Moon

phase

icon

Calendar

Indoor
relative
humidity
in RH%

Indoor

temperature

in ºC/ºF

Outdoor data signal

reception indicator*

Outdoor

temperature

in ºC/ºF

Outdoor
relative
humidity
in RH%

Low battery
indicator
(weather
station)

in R

H

Low battery

indicator
(transmitter)

Time

8

flashing

SET UP

1. First, insert the batteries in the transmitter

(see “To install and replace batteries in
the thermo-hygro transmitter” above).

Keep 5-10 feet from the display for 15
minutes during set up.

2. Within 2 minutes of powering up the
transmitter, insert the batteries in the

Temperature Station (see “To install and
replace batteries in the weather
station” above). Once the batteries are in

place, all segments of the LCD will light up
briefly. Following, the indoor
temperature/humidity and the time, as
12:00 will be displayed. If this information
is not displayed on the LCD after 60
seconds, remove the batteries and wait
for at least 60 seconds before reinserting
them. Once the indoor data is displayed
user may proceed to the next step.

3. After the batteries are inserted, the
weather station will start receiving data
signal from the transmitter. The outdoor
temperature and humidity data should be
displayed on the weather station. If this
does not happen after 2 minutes, the
batteries will need to be removed from
both units and reset from step 1.

4. In order to ensure sufficient 915 MHz
transmission however, the distance
between the Weather Station and the
transmitter should not be more than 330
feet (100 meters) (see notes on

“Positioning” & “915 MHz reception”).

Note:

When changing batteries in the units, ensure the
batteries do not spring free from the contacts.
Always wait at least 15 minutes after removing
the batteries before reinserting, otherwise start
up and transmission problems may occur.

FUNCTION KEYS:

Weather Station:

The Weather Station has 3 easy to use function
keys: 1 key on the front, and 2 keys on the back

SET key

x Press and hold the key to enter manual

setting modes: manual time setting, and
calendar

+ key

x Increase, change, toggle all values in

manual set mode

MIN/MAX key

x Press shortly to toggle between indoor

and outdoor MAX/MIN temperature and
current temperature

LCD SCREEN

The LCD screen is split into 4 sections
displaying the information for time/calendar,
moon phase, indoor data, and outdoor data.

* When the signal is successfully received by the
weather station, the outdoor transmission icon

will be switched on. (If not successful, the icon
will not be shown on LCD). The user can then
easily see whether the last reception was
successful (icon on) or not (icon off).

MANUAL SETTINGS:

The following manual settings can be changed
when pressing the SET key for:

x 12/24 time display setting
x Manual time setting
x Calendar setting
x ºF/ºC temperature display setting

12/24 HOUR TIME DISPLAY SETTING

To set the time format in 12h or 24h display:

1. “12h” or “24h” will flash. (default 12h)

2. Press the + key to select the “12h” or

“24h” display mode.

3. Confirm with the SET key and enter the

“Manual time setting”.

Note:

When 12h mode display is selected, the
calendar format will be "Month. Day" display.
When 24h mode display is selected, the
calendar format will be "Day. Month" display.