Vintage Cellars VintageView Magnum Wall Mounted 18 Bottle Rack User Manual

MAG1 and MAG2 Wall Mount

Wine storage system

Wine Master Cellars •10645 E 47th Ave, Denver, CO 80239 • phone: [phone] • fax: [phone]

Please feel free to contact us regarding the assembly of this product.

Wine Rack Instructions

MAG1 or MAG2 contains:

• 1 Neck Strip

Before starting, open all Packaging for the MAG1 or MAG2 and take inventory to make sure you have everything.

• 1 Spirit Level

• 1 Marking Pen or Pencil

There are three pre-drilled mounting holes in each strip, six total per rack. Appropriate fasteners must be utilized in every

mounting hole for proper installation. Fasteners are not included with your MAG1 or MAG2. However, we recommend the

• Wood Surface: #8 x 1-1/4” wood screw

• Drywall/Wallboard Surface: #8 x 1-1/4” screw with spiral inserts for the bottom two holes in each strip (4 total) and

an expanding hollow wall anchor such as a toggle bolt for the top hole in each strip (2 total)

• Concrete, Brick or Stucco: 3/16” x 1 ¾” masonry screw or #8 x 1 ¼” screw with appropriate size expanding anchor

• 1 Base Strip

following fasteners for these surfaces:

• 2 Plastic Couplers

Tools Needed:

• 1 Tape Measure

• 1 Screwdriver

Fasteners:

• 6 Rubber Mounting Hole Caps

• Drill and Drill Bits (Necessary in Some Cases)

NOTE: If you are attaching the MAG1 or MAG2 to a VintageView® Floor to Ceiling Frame (FCF) you will attach the

units to the FCF using the self-drilling screws included in the FCF packaging.

MAG1 and MAG2 Installation Instructions

1 - Determine which direction the bottle necks
should point.

1.1. If the bottle necks are to point to the right, the base

strip must be installed to the left of the neck strip.

1.2. If the bottle necks are to point to the left, the base

strip must be installed to the right of the neck strip.

2 - Lay out the wall. (Fig. 1)

2.1. The centerline of the rst strip (either base or neck

depending on bottle neck direction) should be at least 3-1/4”

from adjacent walls or obstructions. This allows for the bottle

to overhang the rack.

2.2. From centerline of the rst strip, measure 8-1/2” to the

centerline of the next strip.

Note: This dimension may be altered for specic bottle sizes.

If using the MAG1 or MAG2 racks for sparkling wines/Cham-

pagne, we recommend using 7-1/2” as a centerline-to-cen-

terline measurement between the neck and the base strips.

2.3. (For multiple columns) locate the centerline of the next

strip 6” away from the prior strip.

2.4. (For multiple columns) continue marking the centerlines,

alternating between 8-1/2” (or 7-1/2” for sparkling wines/

Champagne) and 6” increments.

3 1/4"

"

/2

1

"

8

2

/
1

"

6

/2

1

8

Fig. 1

3 - Determine appropriate fasteners for the wall

ACK

surface and fasten the strips to the wall.

3.1. Reference the Fasteners section for recom-

mended fastener types.

3.2. Using a level, ensure that each strip is

plumb prior to securing it to the wall.

3.3. Note that the tops of the strips should be

even. (Bottles resting on the rack will have a

slight neck-down tilt).

3.4. Secure the rack to the wall, using the

appropriate fasteners, through the pre-drilled

mounting holes.

4 - Insert the Mounting Hole Caps.

4.1.Remove the round rubber mounting hole

caps from the bag and snap them into place in

the back strip.

5 - Stacking racks (Optional). (Fig. 2)

5.1. When stacking racks, carefully remove the

black plastic end caps from the top of the lower

strips and from the bottom of the upper strips.

5.2. Fasten the lower strips to the wall per the

above directions, insert the provided black

plastic couplers in the bottom of the upper

strips and slide the strip into place such that the

bottom of the coupler slides into the lower strip.

5.3. Fasten the upper strip in place per the

instructions in step 3.

Fig. 2

SLIDE UPPER R
INTO PLACE & SECURE
W/ APPROPRIATE FASTENERS

LOWER RACKS

ALREADY ATTACHED

S

COUPLER

Warranty

Wine Master Cellars (“WMC”) warrants to the original consumer-purchaser that this product shall be free from defects

in workmanship and materials under normal and reasonable use for the lifetime of the product.

WMC will, at its option, renish or replace any product or part found to be defective during the warranty period and

excludes installation charges, shipping charges, and cost of removal and reinstallation. WMC may require you to return

the part(s) claimed to be defective, for its inspection - freight or postage prepaid.

This warranty does not include the cost of any inconvenience or property damage due to the failure of the product and

does not cover damage due to misuse, abuse, accident, or damage arising out of transportation of this product. THIS

WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER OBLIGATIONS, LIABILITIES OR WARRANTIES. In no event shall

WMC be liable or responsible for INCIDENTAL OR CONSEQUENTIAL DAMAGES or for any other direct or indirect damage,

loss, cost, expense or fee. Neither the WMC distributor nor the retail establishment selling this product has any authority

to make any warranties or to promise remedies in addition to or inconsistent with those stated above. WMC’s maximum

liability, in any event, shall not exceed the purchase price of the product paid by the original consumer-purchaser. Some

states do not allow the exclusion or limitation of incidental or consequential damages. In such a case, the above limita-

tions or exclusions may not be applicable.

This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.